I've been given a HP 9000/D390. It's huge. I've burnt an Etch install
CD (just CD 1 of the official images), but I'm not having a lot of luck
getting it booted with either the 32 or 64 bit kernels. They fail in
different ways and I've attached boot logs of both - a 64 bit boot
fails with a repeating sequence of FLT codes just after "Enumerating
the EISA bus" while a 32 bit kernel prints "Freeing unused kernel
memory: 328k freed" and then just sits there until I press a key at
which point it prints "FLT 0000Kernel panic - not syncing: Kernel
Fault".
This is all over the serial console - there's no graphics card in the
machine. I've ensured the machine is running the latest firmware (42.10)
as I saw some suggestions that could cause issue, but it makes no
difference compared to the revision that was on the machine beforehand
(38.39).
Any suggestions appreciated; equally confirmation that I /should/
expect Etch to run on the D390 would be nice.
J.
--
] http://www.earth.li/~noodles/ [] noodles is destroying the [
] PGP/GPG Key @ the.earth.li [] attractive shape in which they are [
] via keyserver, web or email. [] usually [
] RSA: 4DC4E7FD / DSA: 5B430367 [] [
Firmware Version 42.10
Duplex Console IO Dependent Code (IODC) revision 4
------------------------------------------------------------------------------
(c) Copyright 1995-1998, Hewlett-Packard Company, All rights reserved
------------------------------------------------------------------------------
Processor Speed State Coprocessor State Cache Size
--------- -------- --------------------- ----------------- ----------
0 240 MHz Active Functional 2 MB
Central Bus Speed (in MHz) : 120
Model: D390/1
Available memory (bytes) : 1073741824
Good memory required (bytes): 91570176
Primary boot path: 8/4.5 (dec)
Alternate boot path: 8/16/5.0 (dec)
Console path: 8/0/0.0 (dec)
Keyboard path: 8/16/7.0 (dec)
Processor is booting from first available device.
To discontinue, press any key within 10 seconds.
10 seconds expired.
Proceeding...
Trying Primary Boot Path
------------------------
Booting...
Boot IO Dependent Code (IODC) revision 152
WARN C5F2
IPL error: bad LIF magic.
WARN C5F0 .... FAILED.
Trying Alternate Boot Path
------------------------------------
WARN 80F9
Cannot find ENTRY_TEST.
Failed to initialize.
ENTRY_INIT
Status = -4
0F000080 00000002 00000000 00000000 00000000 00000000 00000000 00000000
00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
00003508 0000001B E80A13A6 01000084 800100DC 00000000 0025F000 00000000
98080000 00019A24 00019A24 00000000 00000002 00000002 0000003A 00000000
WARN 80F5
Failed to initialize.
WARN A70F .... FAILED.
WARN A008
Terminating selection process.
No boot device found.
------- Main Menu -------------------------------------------------------------
Command Description
------- -----------
BOot [PRI|ALT|<path>] Boot from specified path
PAth [PRI|ALT|CON|KEY] [<path>] Display or modify a path
SEArch [DIsplay|IPL] [<path>] Search for boot devices
COnfiguration [<command>] Access Configuration menu/commands
INformation [<command>] Access Information menu/commands
SERvice [<command>] Access Service menu/commands
DIsplay Redisplay the current menu
HElp [<menu>|<command>] Display help for menu or command
RESET Restart the system
-------
Main Menu: Enter command > sea ipl
Searching for device(s) with bootable media...
This may take several minutes.
To discontinue search, press any key (termination may not be immediate).
Path Number Device Path (dec) Device Type and Utilities
----------- ----------------- -------------------------
P0 8/16/5.2 Random access media
IPL
P1 8/16/6.0 LAN Module
Main Menu: Enter command > boot p0
Interact with IPL (Y, N, or Cancel)?> n
Booting...
Boot IO Dependent Code (IODC) revision 1
HARD Booted.
palo ipl 1.14 [EMAIL PROTECTED] Sat Apr 8 16:08:16 EDT 2006
Boot image contains:
0/vmlinux32 4190085 bytes @ 0x33a0000
0/vmlinux64 5796516 bytes @ 0x2e18800
0/ramdisk 4468640 bytes @ 0x29cc800
Information: No console specified on kernel command line. This is normal.
PALO will choose the console currently used by firmware (serial).
Command line for kernel: 'root=/dev/ram ramdisk_size=12580' console=ttyB0
TERM=vt102 palo_kernel=0'0/vmlinux'
Selected kernel: '0/vmlinux from partition 0
Selected ramdisk: /ramdisk from partition 0
Warning: kernel name doesn't end with 32 or 64 -- Guessing...
This box can boot either 32 or 64-bit kernels...Both kernels available,
choosing 32-bit kernelELF32 executable
Entry 00100000 first 00100000 n 3
Segment 0 load 00100000 size 2392744 mediaptr 0x1000
Segment 1 load 00349000 size 499712 mediaptr 0x24a000
Segment 2 load 00400000 size 381060 mediaptr 0x2c4000
Loading ramdisk 4468640 bytes @ 3fbac000...
Branching to kernel entry point 0x00100000. If this is the last
message you see, you may need to switch your console. This is
a common symptom -- search the FAQ and mailing list at parisc-linux.org
Linux version 2.6.18-4-parisc (Debian 2.6.18.dfsg.1-11) ([EMAIL PROTECTED])
(gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #1 Wed Feb 21
07:41:17 MST 2007
FP[0] enabled: Rev 0 Model 14
The 32-bit Kernel has started...
Initialized PDC Console for debugging.
Determining PDC firmware type: System Map.
model 00005b90 00000481 00000000 00000002 77fd44df 100000f0 00000008 000000b2
000000b2
vers 00000501
CPUID vers 14 rev 23 (0x000001d7)
capabilities 0x3
model 9000/800/D390
Total Memory: 1024 MB
initrd: 4fbac000-4ffeefa0
initrd: reserving 3fbac000-3ffeefa0 (mem_max 40000000)
Built 1 zonelists. Total pages: 262144
Kernel command line: root=/dev/ram ramdisk_size=12580' console=ttyB0 TERM=vt102
palo_kernel=0'0/vmlinux
PID hash table entries: 4096 (order: 12, 16384 bytes)
start_kernel(): bug: interrupts were enabled early
Console: colour dummy device 160x64
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1048576k available
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
checking if image is initramfs... it is
Freeing initrd memory: 4363k freed
NET: Registered protocol family 16
EISA bus registered
Searching for devices...
Found devices:
1. U2-IOA BC Runway Port at 0xfff88000 [8] { 12, 0xf, 0x580, 0x0000b }
2. UL 550 Lasi Core BA at 0xffd00000 [8/16] { 11, 0x0, 0x02f, 0x00081 },
additional addresses: 0xffd0c000 0xffc00000
3. UL 550 Core SCSI at 0xffd06000 [8/16/5] { 10, 0x0, 0x02f, 0x00082 }
4. UL 350 Core LAN (802.3) at 0xffd07000 [8/16/6] { 10, 0x0, 0x02f, 0x0008a }
5. UL 550 Core Centronics at 0xffd02000 [8/16/0] { 10, 0x0, 0x02f, 0x00074 },
additional addresses: 0xffd01000 0xffd03000
6. UL 550 Core PS/2 Port at 0xffd08000 [8/16/7] { 10, 0x0, 0x02f, 0x00084 }
7. UL 550 Core PS/2 Port at 0xffd08100 [8/16/8] { 10, 0x0, 0x02f, 0x00084 }
8. UL 550 Core Wax BA at 0xffe00000 [8/20] { 11, 0x0, 0x031, 0x0008e }
9. UL 550 Wax EISA BA at 0xfc000000 [8/20/5] { 11, 0x0, 0x031, 0x00090 },
additional addresses: 0xffc88000
10. UL 550 Wax Core RS-232 at 0xffe02000 [8/20/2] { 10, 0x0, 0x031, 0x0008c }
11. Gecko BOA BC GSC+ Port at 0xf1000000 [8/0] { 7, 0x0, 0x500, 0x0000c }
12. UltraLight CAP/MUX at 0xf1100000 [8/0/0] { 5, 0x0, 0x010, 0x0000d }
13. Gecko BOA BC HP-PB Port at 0xf113c000 [8/0/60] { 7, 0x0, 0x103, 0x0000c }
14. Bluefish Add-on FW-SCSI at 0xf1004000 [8/4] { 4, 0x1, 0x013, 0x00089 }
15. Bluefish Add-on FW-SCSI at 0xf1008000 [8/8] { 4, 0x1, 0x013, 0x00089 }
16. U2-IOA BC GSC+ Port at 0xf103f000 [8/63] { 7, 0x1, 0x501, 0x0000c }
17. U2-IOA BC Runway Port at 0xfff8a000 [10] { 12, 0xf, 0x580, 0x0000b }
18. U2-IOA BC GSC+ Port at 0xf183f000 [10/63] { 7, 0x1, 0x501, 0x0000c }
19. UL 1w U+/240 (350/550) at 0xfffa0000 [32] { 0, 0x0, 0x5b9, 0x00004 }
20. Memory at 0xfffb1000 [49] { 1, 0x0, 0x07d, 0x00009 }
Enabling regular chassis codes support v0.05
CPU(s): 1 x PA8200 (PCX-U+) at 240.000000 MHz
Setting cache flush threshold to f20 (1 CPUs online)
Found U2 at 0xfff88000
Found U2 at 0xfff8a000
Lasi version 0 at 0xffd00000 found.
LED display at ffd0c000 registered
wax at 0xffe00000 found.
Wax EISA Adapter found at 0xfc000000
Enumerating EISA bus
EISA: Probing bus 0 at 8:20:5
EISA: Mainboard HWPC051 detected.
EISA: Detected 0 cards.
Found GeckoBoa at 0xf1000000
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 7, 524288 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
Enabling PDC chassis warnings support v0.05
unwind_init: start = 0x1034acc0, end = 0x1036f7b0, entries = 9391
audit: initializing netlink socket (disabled)
audit(1179682606.384:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
EISA EEPROM at 0x0000c000
PDC Stable Storage facility v0.30
Soft power switch enabled, polling @ 0xf0140000.
STI GSC/PCI core graphics driver Version 0.9a
Generic RTC Driver v1.07
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
8:20:2: ttyS0 at MMIO 0xffe02800 (irq = 22) is a 16550A
Serial mux driver (8 ports) Revision: 0.3
ttyB0 at MMIO 0xf1100800 (polled) is a Mux
ttyB1 at MMIO 0xf1100880 (polled) is a Mux
ttyB2 at MMIO 0xf1100900 (polled) is a Mux
ttyB3 at MMIO 0xf1100980 (polled) is a Mux
ttyB4 at MMIO 0xf1100a00 (polled) is a Mux
ttyB5 at MMIO 0xf1100a80 (polled) is a Mux
ttyB6 at MMIO 0xf1100b00 (polled) is a Mux
ttyB7 at MMIO 0xf1100b80 (polled) is a Mux
RAMDISK driver initialized: 16 RAM disks of 12580K size 1024 blocksize
serio: GSC PS/2 keyboard port at 0x0002e000 irq 19 @ 8:16:7
serio: GSC PS/2 mouse port at 0x00030100 irq 19 @ 8:16:8
mice: PS/2 mouse device common for all mice
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Freeing unused kernel memory: 328k freed
FLT 0000Kernel panic - not syncing: Kernel Fault
Firmware Version 42.10
Duplex Console IO Dependent Code (IODC) revision 4
------------------------------------------------------------------------------
(c) Copyright 1995-1998, Hewlett-Packard Company, All rights reserved
------------------------------------------------------------------------------
Processor Speed State Coprocessor State Cache Size
--------- -------- --------------------- ----------------- ----------
0 240 MHz Active Functional 2 MB
Central Bus Speed (in MHz) : 120
Model: D390/1
Available memory (bytes) : 1073741824
Good memory required (bytes): 91570176
Primary boot path: 8/4.5 (dec)
Alternate boot path: 8/16/5.0 (dec)
Console path: 8/0/0.0 (dec)
Keyboard path: 8/16/7.0 (dec)
Processor is booting from first available device.
To discontinue, press any key within 10 seconds.
10 seconds expired.
Proceeding...
Trying Primary Boot Path
------------------------
Booting...
Boot IO Dependent Code (IODC) revision 152
WARN C5F2
IPL error: bad LIF magic.
WARN C5F0 .... FAILED.
Trying Alternate Boot Path
------------------------------------
WARN 80F9
Cannot find ENTRY_TEST.
Failed to initialize.
ENTRY_INIT
Status = -4
0F000080 00000002 00000000 00000000 00000000 00000000 00000000 00000000
00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
00003508 0000001B E80A13A6 01000084 800100DC 00000000 0025F000 00000000
98080000 00019A24 00019A24 00000000 00000002 00000002 0000003A 00000000
WARN 80F5
Failed to initialize.
WARN A70F .... FAILED.
WARN A008
Terminating selection process.
No boot device found.
------- Main Menu -------------------------------------------------------------
Command Description
------- -----------
BOot [PRI|ALT|<path>] Boot from specified path
PAth [PRI|ALT|CON|KEY] [<path>] Display or modify a path
SEArch [DIsplay|IPL] [<path>] Search for boot devices
COnfiguration [<command>] Access Configuration menu/commands
INformation [<command>] Access Information menu/commands
SERvice [<command>] Access Service menu/commands
DIsplay Redisplay the current menu
HElp [<menu>|<command>] Display help for menu or command
RESET Restart the system
-------
Main Menu: Enter command > sea ipl
Searching for device(s) with bootable media...
This may take several minutes.
To discontinue search, press any key (termination may not be immediate).
Path Number Device Path (dec) Device Type and Utilities
----------- ----------------- -------------------------
P0 8/16/5.2 Random access media
IPL
P1 8/16/6.0 LAN Module
Main Menu: Enter command > boot 09p0
Interact with IPL (Y, N, or Cancel)?> y
Booting...
Boot IO Dependent Code (IODC) revision 1
HARD Booted.
palo ipl 1.14 [EMAIL PROTECTED] Sat Apr 8 16:08:16 EDT 2006
Boot image contains:
0/vmlinux32 4190085 bytes @ 0x33a0000
0/vmlinux64 5796516 bytes @ 0x2e18800
0/ramdisk 4468640 bytes @ 0x29cc800
Information: No console specified on kernel command line. This is normal.
PALO will choose the console currently used by firmware (serial).Current
command line:
'0/vmlinux root=/dev/ram initrd=0/ramdisk ramdisk_size=12580' console=ttyB0
TERM=vt102
0: '0/vmlinux
1: root=/dev/ram
2: initrd=0/ramdisk
3: ramdisk_size=12580'
4: console=ttyB0
5: TERM=vt102
<#> edit the numbered field
'b' boot with this command line
'r' restore command line
'l' list dir
? 0
'0/vmlinux64
Current command line:
'0/vmlinux64 root=/dev/ram initrd=0/ramdisk ramdisk_size=12580' console=ttyB0
TERM=vt102
0: '0/vmlinux64
1: root=/dev/ram
2: initrd=0/ramdisk
3: ramdisk_size=12580'
4: console=ttyB0
5: TERM=vt102
<#> edit the numbered field
'b' boot with this command line
'r' restore command line
'l' list dir
? 0 b
Command line for kernel: 'root=/dev/ram ramdisk_size=12580' console=ttyB0
TERM=vt102 palo_kernel=0'0/vmlinux64'
Selected kernel: '0/vmlinux64 from partition 0
Selected ramdisk: /ramdisk from partition 0
ELF64 executable
Entry 00100000 first 00100000 n 3
Segment 0 load 00100000 size 3850240 mediaptr 0x1000
Segment 1 load 00504000 size 383288 mediaptr 0x3ad000
Segment 2 load 00564000 size 381062 mediaptr 0x40b000
Loading ramdisk 4468640 bytes @ 3fbac000...
Branching to kernel entry point 0x00100000. If this is the last
message you see, you may need to switch your console. This is
a common symptom -- search the FAQ and mailing list at parisc-linux.org
Linux version 2.6.18-4-parisc64 (Debian 2.6.18.dfsg.1-11) ([EMAIL PROTECTED])
(gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #1 Wed Feb 21
10:20:02 MST 2007
FP[0] enabled: Rev 0 Model 14
The 64-bit Kernel has started...
Initialized PDC Console for debugging.
Determining PDC firmware type: System Map.
model 00005b90 00000481 00000000 00000002 77fd44df 100000f0 00000008 000000b2
000000b2
vers 00000501
CPUID vers 14 rev 23 (0x000001d7)
capabilities 0x3
model 9000/800/D390
Total Memory: 1024 MB
initrd: 4fbac000-4ffeefa0
initrd: reserving 3fbac000-3ffeefa0 (mem_max 40000000)
Built 1 zonelists. Total pages: 262144
Kernel command line: root=/dev/ram ramdisk_size=12580' console=ttyB0 TERM=vt102
palo_kernel=0'0/vmlinux64
PID hash table entries: 4096 (order: 12, 32768 bytes)
start_kernel(): bug: interrupts were enabled early
Console: colour dummy device 160x64
Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
Memory: 1048576k available
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 256
checking if image is initramfs... it is
Freeing initrd memory: 4363k freed
NET: Registered protocol family 16
EISA bus registered
Searching for devices...
Found devices:
1. U2-IOA BC Runway Port at 0xfffffffffff88000 [8] { 12, 0xf, 0x580, 0x0000b }
2. UL 550 Lasi Core BA at 0xffffffffffd00000 [8/16] { 11, 0x0, 0x02f, 0x00081
}, additional addresses: 0xffffffffffd0c000 0xffffffffffc00000
3. UL 550 Core SCSI at 0xffffffffffd06000 [8/16/5] { 10, 0x0, 0x02f, 0x00082 }
4. UL 350 Core LAN (802.3) at 0xffffffffffd07000 [8/16/6] { 10, 0x0, 0x02f,
0x0008a }
5. UL 550 Core Centronics at 0xffffffffffd02000 [8/16/0] { 10, 0x0, 0x02f,
0x00074 }, additional addresses: 0xffffffffffd01000 0xffffffffffd03000
6. UL 550 Core PS/2 Port at 0xffffffffffd08000 [8/16/7] { 10, 0x0, 0x02f,
0x00084 }
7. UL 550 Core PS/2 Port at 0xffffffffffd08100 [8/16/8] { 10, 0x0, 0x02f,
0x00084 }
8. UL 550 Core Wax BA at 0xffffffffffe00000 [8/20] { 11, 0x0, 0x031, 0x0008e }
9. UL 550 Wax EISA BA at 0xfffffffffc000000 [8/20/5] { 11, 0x0, 0x031, 0x00090
}, additional addresses: 0xffffffffffc88000
10. UL 550 Wax Core RS-232 at 0xffffffffffe02000 [8/20/2] { 10, 0x0, 0x031,
0x0008c }
11. Gecko BOA BC GSC+ Port at 0xfffffffff1000000 [8/0] { 7, 0x0, 0x500, 0x0000c
}
12. UltraLight CAP/MUX at 0xfffffffff1100000 [8/0/0] { 5, 0x0, 0x010, 0x0000d }
13. Gecko BOA BC HP-PB Port at 0xfffffffff113c000 [8/0/60] { 7, 0x0, 0x103,
0x0000c }
14. Bluefish Add-on FW-SCSI at 0xfffffffff1004000 [8/4] { 4, 0x1, 0x013,
0x00089 }
15. Bluefish Add-on FW-SCSI at 0xfffffffff1008000 [8/8] { 4, 0x1, 0x013,
0x00089 }
16. U2-IOA BC GSC+ Port at 0xfffffffff103f000 [8/63] { 7, 0x1, 0x501, 0x0000c }
17. U2-IOA BC Runway Port at 0xfffffffffff8a000 [10] { 12, 0xf, 0x580, 0x0000b }
18. U2-IOA BC GSC+ Port at 0xfffffffff183f000 [10/63] { 7, 0x1, 0x501, 0x0000c }
19. UL 1w U+/240 (350/550) at 0xfffffffffffa0000 [32] { 0, 0x0, 0x5b9, 0x00004 }
20. Memory at 0xfffffffffffb1000 [49] { 1, 0x0, 0x07d, 0x00009 }
Enabling regular chassis codes support v0.05
CPU(s): 1 x PA8200 (PCX-U+) at 240.000000 MHz
Setting cache flush threshold to 240080 (1 CPUs online)
Found U2 at 0xfffffffffff88000
Found U2 at 0xfffffffffff8a000
Lasi version 0 at 0xffffffffffd00000 found.
LED display at ffffffffffd0c000 registered
wax at 0xffffffffffe00000 found.
Wax EISA Adapter found at 0xfffffffffc000000
Enumerating EISA bus
FLT CBF0FLT 5002FLT 7D03FLT 5408FLT 5508FLT CBF4FLT CBFCFLT CBF0FLT
5002FLT 7D03FLT 5408FLT 5508FLT CBF4FLT CBFCFLT CBF0FLT 5002FLT 7D03FLT
5408FLT 5508FLT CBF4FLT CBFCFLT CBF0FLT 5002FLT 7D03FLT 5408FLT
5508FLT CBF4FLT CBFCFLT CBF0FLT 5002FLT 7D03FLT 5408FLT 5508FLT CBF4FLT
CBFCFLT CBF0FLT 5002FLT 7D03
