Il 16/09/2014 19:39, tar...@aruba.it ha scritto: > Il 16/09/2014 19:36, MaX ha scritto: >> prova ad individuare quale modulo usb è il colpevole. >> Poi fai una regola in /etc/pm/.... per lo sleep, hoberante e il >> wake-up in cui rimuovi il modulo e poi al risveglio lo ricarichi di >> nuovo.
provato con rmmod -f evdev ma si riattiva lo stesso. ps la lucina rossa del sensore del mouse (ottico) resta accesa. estratto di dmesg (la versione completa a fine messaggio) [ 956.887209] PM: Preparing system for mem sleep [ 956.916090] PM: Entering mem sleep !! [ 956.922402] i8042 kbd 00:07: wake-up capability enabled by ACPI [ 957.271230] sd 0:0:0:0: [sda] Stopping disk [ 957.696082] PM: suspend of devices complete after 779.858 msecs !! [ 957.728080] ehci_hcd 0000:00:02.1: wake-up capability enabled by ACPI !! [ 957.744067] ohci_hcd 0000:00:02.0: wake-up capability enabled by ACPI [ 957.760126] PM: late suspend of devices complete after 64.037 msecs [ 957.760188] ACPI: Preparing to enter system sleep state S3 [ 958.160508] PM: Saving platform NVS memory [ 958.160774] Disabling non-boot CPUs ... [ 958.264024] CPU 1 is now offline [ 958.264508] ACPI: Low-level resume complete ... che diavolo è i8042? e perché diavolo acpi riattiva il wake-up sulle porte usb? rimosso acpi* riavvio niente. come prima. sgrunt! -- versione completa dmesg [ 955.155631] wlan0: deauthenticating from 00:0c:42:6a:b2:39 by local choice (reason=3) [ 955.166149] cfg80211: Calling CRDA to update world regulatory domain [ 955.211126] cfg80211: World regulatory domain updated: [ 955.211129] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 955.211132] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm) [ 955.211134] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm) [ 955.211136] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm) [ 955.211138] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm) [ 955.211140] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm) [ 955.211142] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm) [ 956.859419] PM: Syncing filesystems ... done. [ 956.887209] PM: Preparing system for mem sleep [ 956.887222] Freezing user space processes ... (elapsed 0.01 seconds) done. [ 956.900089] Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done. [ 956.916090] PM: Entering mem sleep [ 956.916120] Suspending console(s) (use no_console_suspend to debug) [ 956.916312] sd 2:0:0:0: [sdb] Synchronizing SCSI cache [ 956.916425] sd 0:0:0:0: [sda] Synchronizing SCSI cache [ 956.916522] sd 2:0:0:0: [sdb] Stopping disk [ 956.922206] serial 00:08: disabled [ 956.922212] serial 00:08: wake-up capability disabled by ACPI [ 956.922402] i8042 kbd 00:07: wake-up capability enabled by ACPI [ 957.271230] sd 0:0:0:0: [sda] Stopping disk [ 957.696082] PM: suspend of devices complete after 779.858 msecs [ 957.728080] ehci_hcd 0000:00:02.1: wake-up capability enabled by ACPI [ 957.744067] ohci_hcd 0000:00:02.0: wake-up capability enabled by ACPI [ 957.760126] PM: late suspend of devices complete after 64.037 msecs [ 957.760188] ACPI: Preparing to enter system sleep state S3 [ 958.160508] PM: Saving platform NVS memory [ 958.160774] Disabling non-boot CPUs ... [ 958.264024] CPU 1 is now offline [ 958.264508] ACPI: Low-level resume complete [ 958.264508] PM: Restoring platform NVS memory [ 958.264508] PCI-DMA: Resuming GART IOMMU [ 958.264508] PCI-DMA: Restoring GART aperture settings [ 958.264508] Enabling non-boot CPUs ... [ 958.264508] Booting Node 0 Processor 1 APIC 0x1 [ 958.264508] smpboot cpu 1: start_ip = 9a000 [ 958.162149] Calibrating delay loop (skipped) already calibrated this CPU [ 958.162149] [Firmware Bug]: cpu 1, try to use APIC500 (LVT offset 0) for vector 0x400, but the register is already in use for vector 0xf9 on another cpu [ 958.162149] perf: IBS APIC setup failed on cpu #1 [ 958.296745] NMI watchdog enabled, takes one hw-pmu counter. [ 958.300058] CPU1 is up [ 958.300504] ACPI: Waking up from system sleep state S3 [ 958.301173] ohci_hcd 0000:00:02.0: wake-up capability disabled by ACPI [ 958.301198] ehci_hcd 0000:00:02.1: wake-up capability disabled by ACPI [ 958.301251] pci 0000:00:00.0: Found enabled HT MSI Mapping [ 958.301310] pci 0000:00:00.0: Found enabled HT MSI Mapping [ 958.301371] pci 0000:00:00.0: Found enabled HT MSI Mapping [ 958.301430] pci 0000:00:00.0: Found enabled HT MSI Mapping [ 958.301489] pci 0000:00:00.0: Found enabled HT MSI Mapping [ 958.301558] pci 0000:00:00.0: Found enabled HT MSI Mapping [ 958.301629] pci 0000:00:00.0: Found enabled HT MSI Mapping [ 958.301703] pci 0000:00:00.0: Found enabled HT MSI Mapping [ 958.301811] PM: early resume of devices complete after 0.785 msecs [ 958.301916] ohci_hcd 0000:00:02.0: setting latency timer to 64 [ 958.301934] ehci_hcd 0000:00:02.1: setting latency timer to 64 [ 958.301971] pci 0000:00:04.0: setting latency timer to 64 [ 958.302096] snd_hda_intel 0000:00:05.0: setting latency timer to 64 [ 958.302232] sata_nv 0000:00:08.0: setting latency timer to 64 [ 958.302245] sata_nv 0000:00:08.1: setting latency timer to 64 [ 958.302548] sd 0:0:0:0: [sda] Starting disk [ 958.302576] sd 2:0:0:0: [sdb] Starting disk [ 958.303118] i8042 kbd 00:07: wake-up capability disabled by ACPI [ 958.303638] serial 00:08: activated [ 958.768083] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 958.768171] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 958.768250] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 958.776210] ata3.00: ACPI cmd ef/03:46:00:00:00:a0 (SET FEATURES) filtered out [ 958.776263] ata4.00: ACPI cmd ef/03:45:00:00:00:a0 (SET FEATURES) filtered out [ 958.792243] ata4.00: configured for UDMA/100 [ 958.792399] ata3.00: configured for UDMA/133 [ 958.800191] ata1.00: ACPI cmd ef/03:46:00:00:00:a0 (SET FEATURES) filtered out [ 958.813056] ata1.00: configured for UDMA/133 [ 958.832065] usb 2-8: reset low-speed USB device number 3 using ohci_hcd [ 959.034284] ata2: SATA link down (SStatus 0 SControl 300) [ 959.190151] PM: resume of devices complete after 888.299 msecs [ 959.190303] PM: Finishing wakeup. [ 959.190304] Restarting tasks ... done. [ 962.892325] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 962.907376] forcedeth 0000:00:07.0: irq 43 for MSI/MSI-X [ 962.907571] forcedeth 0000:00:07.0: eth0: no link during initialization [ 962.912718] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 964.652073] wlan0: authenticate with 00:0c:42:6a:b2:39 (try 1) [ 964.653558] wlan0: authenticated [ 964.653850] wlan0: associate with 00:0c:42:6a:b2:39 (try 1) [ 964.658051] wlan0: RX AssocResp from 00:0c:42:6a:b2:39 (capab=0x421 status=0 aid=2) [ 964.658054] wlan0: associated [ 964.658846] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready -- Per REVOCARE l'iscrizione alla lista, inviare un email a debian-italian-requ...@lists.debian.org con oggetto "unsubscribe". Per problemi inviare un email in INGLESE a listmas...@lists.debian.org To UNSUBSCRIBE, email to debian-italian-requ...@lists.debian.org with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org Archive: https://lists.debian.org/54193b4d.2060...@aruba.it