I had the same issue. Doing this, I have no more problems: #/etc/modprobe.d/blacklist-hp.conf blacklist hpwdt
On Thu, 14 Aug 2025 at 02:20, Thorsten Sperber <[email protected]> wrote: > Package: src:linux > Version: 6.12.38-1 > Severity: normal > X-Debbugs-Cc: [email protected] > User: [email protected] > Usertags: amd64 > > Dear Maintainer, > > after upgrading to trixie, the HP Microserver Gen8 started to crash > randomly, hard, to system error (blinking red light in the front, not > recoverable with reset but only removing power, IPMI/ILO still usable > though). > > No dmesg/stacktrace visible. > > IML (Integrated Management Log from ILO) says: > > Unrecoverable System Error (NMI) has occurred. System Firmware will log > additional details in a separate IML entry if possible > > (no additional information can be found) > > This can happen within half an hour after boot or 12 hours later, so > debugging might be a little hard. I rolled back to the bookworm kernel > and it has been running stable for 20 hours now. > > I found somewhat related bugs (#898336, #995773) with NMI stacktraces > mentioning the wdt > module - this isn't loaded in 6.1, haven't booted 6.12 again to check. > Also haven't tried fiddling with boot options, since it takes ages to > reproduce. > > I'm running iLO 4 2.82 since 2023 - which is the latest firmware to my > knowledge. > > -- Package-specific info: > ** Kernel log: boot messages should be attached > > ** Model information > sys_vendor: HP > product_name: ProLiant MicroServer Gen8 > product_version: > chassis_vendor: HP > chassis_version: > bios_vendor: HP > bios_version: J06 > > ** Configuration for modprobe: > blacklist microcode > blacklist arkfb > blacklist aty128fb > blacklist atyfb > blacklist radeonfb > blacklist cirrusfb > blacklist cyber2000fb > blacklist kyrofb > blacklist matroxfb_base > blacklist mb862xxfb > blacklist neofb > blacklist pm2fb > blacklist pm3fb > blacklist s3fb > blacklist savagefb > blacklist sisfb > blacklist tdfxfb > blacklist tridentfb > blacklist vt8623fb > blacklist microcode > options snd_pcsp index=-2 > options cx88_alsa index=-2 > options snd_atiixp_modem index=-2 > options snd_intel8x0m index=-2 > options snd_via82xx_modem index=-2 > options md_mod start_ro=1 > options bonding max_bonds=0 > options dummy numdummies=0 > options ifb numifbs=0 > > ** PCI devices: > 00:00.0 Host bridge [0600]: Intel Corporation Xeon E3-1200 v2/Ivy Bridge > DRAM Controller [8086:0158] (rev 09) > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > ParErr+ Stepping- SERR+ FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort+ >SERR- <PERR- INTx- > Latency: 0 > Capabilities: <access denied> > Kernel driver in use: ie31200_edac > Kernel modules: ie31200_edac > > 00:01.0 PCI bridge [0604]: Intel Corporation Xeon E3-1200 v2/3rd Gen Core > processor PCI Express Root Port [8086:0151] (rev 09) (prog-if 00 [Normal > decode]) > Subsystem: Hewlett-Packard Company Device [103c:330b] > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > ParErr+ Stepping- SERR+ FastB2B- DisINTx+ > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 64 bytes > Interrupt: pin A routed to IRQ 24 > Bus: primary=00, secondary=07, subordinate=07, sec-latency=0 > I/O behind bridge: [disabled] [16-bit] > Memory behind bridge: fbf00000-fbffffff [size=1M] [32-bit] > Prefetchable memory behind bridge: [disabled] [64-bit] > Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort+ <SERR- <PERR- > BridgeCtl: Parity+ SERR+ NoISA- VGA- VGA16- MAbort- >Reset- > FastB2B- > PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- > Capabilities: <access denied> > Kernel driver in use: pcieport > > 00:06.0 PCI bridge [0604]: Intel Corporation Xeon E3-1200 v2/3rd Gen Core > processor PCI Express Root Port [8086:015d] (rev 09) (prog-if 00 [Normal > decode]) > Subsystem: Hewlett-Packard Company Device [103c:330b] > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > ParErr+ Stepping- SERR+ FastB2B- DisINTx+ > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 64 bytes > Interrupt: pin A routed to IRQ 25 > Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 > I/O behind bridge: [disabled] [16-bit] > Memory behind bridge: fbd00000-fbdfffff [size=1M] [32-bit] > Prefetchable memory behind bridge: c0000000-dfffffff [size=512M] > [32-bit] > Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- <SERR- <PERR- > BridgeCtl: Parity+ SERR+ NoISA- VGA- VGA16- MAbort- >Reset- > FastB2B- > PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- > Capabilities: <access denied> > Kernel driver in use: pcieport > > 00:1a.0 USB controller [0c03]: Intel Corporation 6 Series/C200 Series > Chipset Family USB Enhanced Host Controller #2 [8086:1c2d] (rev 05) > (prog-if 20 [EHCI]) > Subsystem: Hewlett-Packard Company Device [103c:330d] > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > ParErr+ Stepping- SERR+ FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0 > Interrupt: pin A routed to IRQ 21 > Region 0: Memory at facf0000 (32-bit, non-prefetchable) [size=1K] > Capabilities: <access denied> > Kernel driver in use: ehci-pci > Kernel modules: ehci_pci > > 00:1c.0 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset > Family PCI Express Root Port 1 [8086:1c10] (rev b5) (prog-if 00 [Normal > decode]) > Subsystem: Hewlett-Packard Company Device [103c:330d] > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > ParErr+ Stepping- SERR+ FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 64 bytes > Interrupt: pin A routed to IRQ 16 > Bus: primary=00, secondary=0d, subordinate=0d, sec-latency=0 > I/O behind bridge: [disabled] [16-bit] > Memory behind bridge: [disabled] [32-bit] > Prefetchable memory behind bridge: [disabled] [64-bit] > Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort+ <SERR- <PERR- > BridgeCtl: Parity+ SERR+ NoISA- VGA- VGA16- MAbort- >Reset- > FastB2B- > PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- > Capabilities: <access denied> > Kernel driver in use: pcieport > > 00:1c.4 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset > Family PCI Express Root Port 5 [8086:1c18] (rev b5) (prog-if 00 [Normal > decode]) > Subsystem: Hewlett-Packard Company Device [103c:330d] > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > ParErr+ Stepping- SERR+ FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 64 bytes > Interrupt: pin A routed to IRQ 16 > Bus: primary=00, secondary=03, subordinate=03, sec-latency=0 > I/O behind bridge: [disabled] [16-bit] > Memory behind bridge: bc000000-bc0fffff [size=1M] [32-bit] > Prefetchable memory behind bridge: fab00000-fabfffff [size=1M] > [32-bit] > Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort+ <SERR- <PERR- > BridgeCtl: Parity+ SERR+ NoISA- VGA- VGA16- MAbort- >Reset- > FastB2B- > PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- > Capabilities: <access denied> > Kernel driver in use: pcieport > > 00:1c.6 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset > Family PCI Express Root Port 7 [8086:1c1c] (rev b5) (prog-if 00 [Normal > decode]) > Subsystem: Hewlett-Packard Company Device [103c:330d] > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > ParErr+ Stepping- SERR+ FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 64 bytes > Interrupt: pin C routed to IRQ 18 > Bus: primary=00, secondary=04, subordinate=04, sec-latency=0 > I/O behind bridge: [disabled] [16-bit] > Memory behind bridge: fbe00000-fbefffff [size=1M] [32-bit] > Prefetchable memory behind bridge: [disabled] [64-bit] > Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- <SERR- <PERR- > BridgeCtl: Parity+ SERR+ NoISA- VGA- VGA16- MAbort- >Reset- > FastB2B- > PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- > Capabilities: <access denied> > Kernel driver in use: pcieport > > 00:1c.7 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset > Family PCI Express Root Port 8 [8086:1c1e] (rev b5) (prog-if 00 [Normal > decode]) > Subsystem: Hewlett-Packard Company Device [103c:330d] > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > ParErr+ Stepping- SERR+ FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 64 bytes > Interrupt: pin D routed to IRQ 19 > Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 > I/O behind bridge: 3000-3fff [size=4K] [16-bit] > Memory behind bridge: fad00000-fbcfffff [size=16M] [32-bit] > Prefetchable memory behind bridge: bf000000-bfffffff [size=16M] > [32-bit] > Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort+ <SERR- <PERR- > BridgeCtl: Parity+ SERR+ NoISA- VGA+ VGA16- MAbort- >Reset- > FastB2B- > PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- > Capabilities: <access denied> > Kernel driver in use: pcieport > > 00:1d.0 USB controller [0c03]: Intel Corporation 6 Series/C200 Series > Chipset Family USB Enhanced Host Controller #1 [8086:1c26] (rev 05) > (prog-if 20 [EHCI]) > Subsystem: Hewlett-Packard Company Device [103c:330d] > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > ParErr+ Stepping- SERR+ FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0 > Interrupt: pin A routed to IRQ 20 > Region 0: Memory at face0000 (32-bit, non-prefetchable) [size=1K] > Capabilities: <access denied> > Kernel driver in use: ehci-pci > Kernel modules: ehci_pci > > 00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] > (rev a5) (prog-if 01 [Subtractive decode]) > Subsystem: Hewlett-Packard Company Device [103c:330d] > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > ParErr+ Stepping- SERR+ FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0 > Bus: primary=00, secondary=14, subordinate=14, sec-latency=32 > I/O behind bridge: [disabled] [16-bit] > Memory behind bridge: [disabled] [32-bit] > Prefetchable memory behind bridge: [disabled] [64-bit] > Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort+ <SERR- <PERR- > BridgeCtl: Parity+ SERR+ NoISA- VGA- VGA16- MAbort- >Reset- > FastB2B- > PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- > Capabilities: <access denied> > > 00:1f.0 ISA bridge [0601]: Intel Corporation C204 Chipset LPC Controller > [8086:1c54] (rev 05) > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > ParErr+ Stepping- SERR+ FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0 > Capabilities: <access denied> > Kernel driver in use: lpc_ich > Kernel modules: lpc_ich > > 00:1f.2 RAID bus controller [0104]: Intel Corporation 6 Series/C200 Series > Desktop SATA RAID Controller [8086:1c04] (rev 05) > Subsystem: Hewlett Packard Enterprise Device [1590:006c] > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > ParErr+ Stepping- SERR- FastB2B- DisINTx+ > Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0 > Interrupt: pin B routed to IRQ 26 > Region 0: I/O ports at 10c0 [size=8] > Region 1: I/O ports at 10c8 [size=4] > Region 2: I/O ports at 10d0 [size=8] > Region 3: I/O ports at 10d8 [size=4] > Region 4: I/O ports at 10e0 [size=32] > Region 5: Memory at facd0000 (32-bit, non-prefetchable) [size=2K] > Capabilities: <access denied> > Kernel driver in use: ahci > Kernel modules: ahci > > 01:00.0 System peripheral [0880]: Hewlett-Packard Company Integrated > Lights-Out Standard Slave Instrumentation & System Support [103c:3306] (rev > 05) > Subsystem: Hewlett-Packard Company iLO4 [103c:3381] > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > ParErr- Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 64 bytes > Interrupt: pin A routed to IRQ 10 > Region 0: I/O ports at 3000 [size=256] > Region 1: Memory at fbcf0000 (32-bit, non-prefetchable) [size=512] > Region 2: I/O ports at 3400 [size=256] > Capabilities: <access denied> > Kernel modules: hpwdt > > 01:00.1 VGA compatible controller [0300]: Matrox Electronics Systems Ltd. > MGA G200EH [102b:0533] (prog-if 00 [VGA controller]) > Subsystem: Hewlett-Packard Company iLO4 [103c:3381] > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > ParErr+ Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 64 bytes > Interrupt: pin B routed to IRQ 16 > Region 0: Memory at bf000000 (32-bit, prefetchable) [size=16M] > Region 1: Memory at fbce0000 (32-bit, non-prefetchable) [size=16K] > Region 2: Memory at fb000000 (32-bit, non-prefetchable) [size=8M] > Expansion ROM at 000c0000 [virtual] [disabled] [size=128K] > Capabilities: <access denied> > Kernel driver in use: mgag200 > Kernel modules: mgag200 > > 01:00.2 System peripheral [0880]: Hewlett-Packard Company Integrated > Lights-Out Standard Management Processor Support and Messaging [103c:3307] > (rev 05) > Subsystem: Hewlett-Packard Company iLO4 [103c:3381] > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > ParErr- Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 64 bytes > Interrupt: pin B routed to IRQ 16 > Region 0: I/O ports at 3800 [size=256] > Region 1: Memory at faff0000 (32-bit, non-prefetchable) [size=256] > Region 2: Memory at fae00000 (32-bit, non-prefetchable) [size=1M] > Region 3: Memory at fad80000 (32-bit, non-prefetchable) [size=512K] > Region 4: Memory at fad70000 (32-bit, non-prefetchable) [size=32K] > Region 5: Memory at fad60000 (32-bit, non-prefetchable) [size=32K] > Expansion ROM at fad00000 [virtual] [disabled] [size=64K] > Capabilities: <access denied> > Kernel driver in use: hpilo > Kernel modules: hpilo > > 01:00.4 USB controller [0c03]: Hewlett-Packard Company Integrated > Lights-Out Standard Virtual USB Controller [103c:3300] (rev 02) (prog-if 00 > [UHCI]) > Subsystem: Hewlett-Packard Company iLO4 [103c:3381] > Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- > ParErr+ Stepping- SERR- FastB2B- DisINTx+ > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 64 bytes > Interrupt: pin B routed to IRQ 35 > Region 4: I/O ports at 3c00 [size=32] > Capabilities: <access denied> > Kernel driver in use: uhci_hcd > Kernel modules: uhci_hcd > > 02:00.0 Memory controller [0580]: Hewlett Packard Enterprise Device > [1590:005f] > DeviceName: Memory Controller > Subsystem: Hewlett Packard Enterprise Device [1590:005f] > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > ParErr+ Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 64 bytes > Interrupt: pin A routed to IRQ 11 > Region 0: Memory at c0000000 (64-bit, prefetchable) [size=512M] > Region 2: Memory at fbdf0000 (64-bit, non-prefetchable) [size=32K] > Capabilities: <access denied> > > 03:00.0 Ethernet controller [0200]: Broadcom Inc. and subsidiaries > NetXtreme BCM5720 Gigabit Ethernet PCIe [14e4:165f] > DeviceName: NIC Port 1 > Subsystem: Hewlett-Packard Company NC332i Adapter [103c:2133] > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > ParErr+ Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 64 bytes > Interrupt: pin A routed to IRQ 16 > Region 0: Memory at fabf0000 (64-bit, prefetchable) [size=64K] > Region 2: Memory at fabe0000 (64-bit, prefetchable) [size=64K] > Region 4: Memory at fabd0000 (64-bit, prefetchable) [size=64K] > Expansion ROM at bc000000 [virtual] [disabled] [size=128K] > Capabilities: <access denied> > Kernel driver in use: tg3 > Kernel modules: tg3 > > 03:00.1 Ethernet controller [0200]: Broadcom Inc. and subsidiaries > NetXtreme BCM5720 Gigabit Ethernet PCIe [14e4:165f] > DeviceName: NIC Port 2 > Subsystem: Hewlett-Packard Company NC332i Adapter [103c:2133] > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > ParErr+ Stepping- SERR- FastB2B- DisINTx+ > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 64 bytes > Interrupt: pin B routed to IRQ 17 > Region 0: Memory at fabc0000 (64-bit, prefetchable) [size=64K] > Region 2: Memory at fabb0000 (64-bit, prefetchable) [size=64K] > Region 4: Memory at faba0000 (64-bit, prefetchable) [size=64K] > Expansion ROM at bc020000 [virtual] [disabled] [size=128K] > Capabilities: <access denied> > Kernel driver in use: tg3 > Kernel modules: tg3 > > 04:00.0 USB controller [0c03]: Renesas Electronics Corp. uPD720201 USB 3.0 > Host Controller [1912:0014] (rev 03) (prog-if 30 [XHCI]) > Subsystem: Hewlett-Packard Company Device [103c:1996] > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > ParErr+ Stepping- SERR- FastB2B- DisINTx+ > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 64 bytes > Interrupt: pin A routed to IRQ 18 > Region 0: Memory at fbef0000 (64-bit, non-prefetchable) [size=8K] > Capabilities: <access denied> > Kernel driver in use: xhci_hcd > Kernel modules: xhci_pci > > 07:00.0 USB controller [0c03]: ASMedia Technology Inc. ASM2142/ASM3142 USB > 3.1 Host Controller [1b21:2142] (prog-if 30 [XHCI]) > Subsystem: Post Impression Systems. Device [3142:1b21] > Physical Slot: 1 > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > ParErr+ Stepping- SERR- FastB2B- DisINTx+ > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 64 bytes > Interrupt: pin A routed to IRQ 16 > Region 0: Memory at fbff0000 (64-bit, non-prefetchable) [size=32K] > Capabilities: <access denied> > Kernel driver in use: xhci_hcd > Kernel modules: xhci_pci > > > ** USB devices: > Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub > Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub > Bus 001 Device 003: ID 13fe:1d00 Phison Electronics Corp. DataTraveler 2.0 > 1GB/4GB Flash Drive / Patriot Xporter 4GB Flash Drive > Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub > Bus 002 Device 002: ID 2109:2822 VIA Labs, Inc. USB2.0 Hub > Bus 003 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub > Bus 003 Device 002: ID 2109:0822 VIA Labs, Inc. USB3.1 Hub > Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub > Bus 004 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub > Bus 004 Device 003: ID 0424:2660 Microchip Technology, Inc. (formerly > SMSC) Hub > Bus 005 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub > Bus 005 Device 003: ID 0bda:5411 Realtek Semiconductor Corp. RTS5411 Hub > Bus 005 Device 004: ID 8564:1000 Transcend Information, Inc. JetFlash > Bus 005 Device 005: ID 0bda:5411 Realtek Semiconductor Corp. RTS5411 Hub > Bus 005 Device 006: ID 0bda:5411 Realtek Semiconductor Corp. RTS5411 Hub > Bus 005 Device 007: ID 1cf1:0030 Dresden Elektronik ZigBee gateway [ConBee > II] > Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub > Bus 007 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub > Bus 007 Device 002: ID 0bda:0411 Realtek Semiconductor Corp. Hub > Bus 007 Device 003: ID 0bda:0411 Realtek Semiconductor Corp. Hub > Bus 007 Device 004: ID 0bda:0411 Realtek Semiconductor Corp. Hub > > > -- System Information: > Debian Release: 13.0 > APT prefers stable-updates > APT policy: (500, 'stable-updates'), (500, 'stable-security'), (500, > 'stable'), (500, 'oldstable') > Architecture: amd64 (x86_64) > > Kernel: Linux 6.1.0-35-amd64 (SMP w/8 CPU threads; PREEMPT) > Locale: LANG=de_DE.UTF-8, LC_CTYPE=de_DE.UTF-8 (charmap=UTF-8), LANGUAGE > not set > Shell: /bin/sh linked to /usr/bin/dash > Init: systemd (via /run/systemd/system) > LSM: AppArmor: enabled > > Versions of packages linux-image-6.12.38+deb13-amd64 depends on: > ii initramfs-tools [linux-initramfs-tool] 0.148.3 > ii kmod 34.2-2 > ii linux-base 4.12 > > Versions of packages linux-image-6.12.38+deb13-amd64 recommends: > ii apparmor 4.1.0-1 > > Versions of packages linux-image-6.12.38+deb13-amd64 suggests: > pn debian-kernel-handbook <none> > ii firmware-linux-free 20241210-2 > ii grub-pc 2.12-9 > pn linux-doc-6.12 <none> > > Versions of packages linux-image-6.12.38+deb13-amd64 is related to: > ii firmware-amd-graphics 20250410-2 > pn firmware-atheros <none> > pn firmware-bnx2 <none> > pn firmware-bnx2x <none> > pn firmware-brcm80211 <none> > pn firmware-cavium <none> > pn firmware-cirrus <none> > ii firmware-intel-graphics 20250410-2 > ii firmware-intel-misc 20250410-2 > pn firmware-intel-sound <none> > pn firmware-ipw2x00 <none> > pn firmware-ivtv <none> > pn firmware-iwlwifi <none> > pn firmware-libertas <none> > pn firmware-marvell-prestera <none> > ii firmware-mediatek 20250410-2 > ii firmware-misc-nonfree 20250410-2 > pn firmware-myricom <none> > pn firmware-netronome <none> > pn firmware-netxen <none> > ii firmware-nvidia-graphics 20250410-2 > pn firmware-qcom-soc <none> > pn firmware-qlogic <none> > pn firmware-realtek <none> > pn firmware-samsung <none> > pn firmware-siano <none> > pn firmware-ti-connectivity <none> > pn xen-hypervisor <none> > > -- no debconf information > > -- Marcos R Carot
