Package: linux-image-2.6.22-3-686
Version: 2.6.22-6
Severity: normal
Hi,
After upgrading to linux-image-2.6.22-3, networking no longer works. In
fact, lspci does no longer show the network card at all.
linux-image-2.6.20-1 (version 2.6.20-3) works fine. dmesg and lspci for
both versions are below; I think the most significant part is this
change in dmesg:
PCI: Bridge: 0000:00:1e.0
- IO window: d000-dfff
- MEM window: fea00000-feafffff
+ IO window: disabled.
+ MEM window: disabled.
PREFETCH window: disabled.
The network card (driven by 8139too) is behind that bridge...
The MB is an Asus P4P800S/SE.
Gabor
lspci -vvnn with 2.6.20-3:
==========================
00:00.0 Host bridge [0600]: Intel Corporation 82865G/PE/P DRAM
Controller/Host-Hub Interface [8086:2570] (rev 02)
Subsystem: ASUSTeK Computer Inc. Unknown device [1043:8110]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR-
Latency: 0
Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M]
Capabilities: [e4] Vendor Specific Information
Capabilities: [a0] AGP version 3.0
Status: RQ=32 Iso- ArqSz=2 Cal=2 SBA+ ITACoh- GART64- HTrans-
64bit- FW+ AGP3+ Rate=x4,x8
Command: RQ=1 ArqSz=0 Cal=2 SBA+ AGP- GART64- 64bit- FW-
Rate=<none>
00:01.0 PCI bridge [0604]: Intel Corporation 82865G/PE/P PCI to AGP Controller
[8086:2571] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
Memory behind bridge: fc900000-fe9fffff
Prefetchable memory behind bridge: e7f00000-f7efffff
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
00:1d.0 USB Controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB
UHCI Controller #1 [8086:24d2] (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. P5P800-MX Mainboard [1043:80a6]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 17
Region 4: I/O ports at ef00 [size=32]
00:1d.1 USB Controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB
UHCI Controller #2 [8086:24d4] (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. P5P800-MX Mainboard [1043:80a6]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 18
Region 4: I/O ports at ef20 [size=32]
00:1d.2 USB Controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB
UHCI Controller #3 [8086:24d7] (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. P5P800-MX Mainboard [1043:80a6]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 19
Region 4: I/O ports at ef40 [size=32]
00:1d.3 USB Controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB
UHCI Controller #4 [8086:24de] (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. P5P800-MX Mainboard [1043:80a6]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 17
Region 4: I/O ports at ef80 [size=32]
00:1d.7 USB Controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB2
EHCI Controller [8086:24dd] (rev 02) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. P5P800-MX Mainboard [1043:80a6]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 20
Region 0: Memory at febffc00 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev
c2) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=64
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fea00000-feafffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
00:1f.0 ISA bridge [0601]: Intel Corporation 82801EB/ER (ICH5/ICH5R) LPC
Interface Bridge [8086:24d0] (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:1f.1 IDE interface [0101]: Intel Corporation 82801EB/ER (ICH5/ICH5R) IDE
Controller [8086:24db] (rev 02) (prog-if 8a [Master SecP PriP])
Subsystem: ASUSTeK Computer Inc. P5P800-MX Mainboard [1043:80a6]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 19
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at fc00 [size=16]
Region 5: Memory at 30000000 (32-bit, non-prefetchable) [size=1K]
00:1f.3 SMBus [0c05]: Intel Corporation 82801EB/ER (ICH5/ICH5R) SMBus
Controller [8086:24d3] (rev 02)
Subsystem: ASUSTeK Computer Inc. P4P800 Mainboard [1043:80a6]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at 0400 [size=32]
00:1f.5 Multimedia audio controller [0401]: Intel Corporation 82801EB/ER
(ICH5/ICH5R) AC'97 Audio Controller [8086:24d5] (rev 02)
Subsystem: ASUSTeK Computer Inc. Unknown device [1043:810d]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 21
Region 0: I/O ports at e800 [size=256]
Region 1: I/O ports at ee80 [size=64]
Region 2: Memory at febff800 (32-bit, non-prefetchable) [size=512]
Region 3: Memory at febff400 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:00.0 VGA compatible controller [0300]: nVidia Corporation NV34 [GeForce FX
5200] [10de:0322] (rev a1) (prog-if 00 [VGA])
Subsystem: ASUSTeK Computer Inc. Unknown device [1043:80cf]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (1250ns min, 250ns max)
Interrupt: pin A routed to IRQ 10
Region 0: Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at e8000000 (32-bit, prefetchable) [size=128M]
Expansion ROM at fe9e0000 [disabled] [size=128K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [44] AGP version 3.0
Status: RQ=32 Iso- ArqSz=0 Cal=3 SBA+ ITACoh- GART64- HTrans-
64bit- FW+ AGP3+ Rate=x4,x8
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW-
Rate=<none>
02:05.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd.
RTL-8139/8139C/8139C+ [10ec:8139] (rev 10)
Subsystem: ASUSTeK Computer Inc. P5P800-MX Mainboard [1043:8109]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at d800 [size=256]
Region 1: Memory at feaffc00 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
lspci -vvnn with 2.6.22-3:
==========================
00:00.0 Host bridge [0600]: Intel Corporation 82865G/PE/P DRAM
Controller/Host-Hub Interface [8086:2570] (rev 02)
Subsystem: ASUSTeK Computer Inc. Unknown device [1043:8110]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR-
Latency: 0
Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M]
Capabilities: [e4] Vendor Specific Information
Capabilities: [a0] AGP version 3.0
Status: RQ=32 Iso- ArqSz=2 Cal=2 SBA+ ITACoh- GART64- HTrans-
64bit- FW+ AGP3+ Rate=x4,x8
Command: RQ=1 ArqSz=0 Cal=2 SBA+ AGP- GART64- 64bit- FW-
Rate=<none>
00:01.0 PCI bridge [0604]: Intel Corporation 82865G/PE/P PCI to AGP Controller
[8086:2571] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
Memory behind bridge: fca00000-feafffff
Prefetchable memory behind bridge: e7f00000-f7efffff
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
00:1d.0 USB Controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB
UHCI Controller #1 [8086:24d2] (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. P5P800-MX Mainboard [1043:80a6]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at ef00 [size=32]
00:1d.1 USB Controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB
UHCI Controller #2 [8086:24d4] (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. P5P800-MX Mainboard [1043:80a6]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 4: I/O ports at ef20 [size=32]
00:1d.2 USB Controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB
UHCI Controller #3 [8086:24d7] (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. P5P800-MX Mainboard [1043:80a6]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at ef40 [size=32]
00:1d.3 USB Controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB
UHCI Controller #4 [8086:24de] (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. P5P800-MX Mainboard [1043:80a6]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at ef80 [size=32]
00:1d.7 USB Controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB2
EHCI Controller [8086:24dd] (rev 02) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. P5P800-MX Mainboard [1043:80a6]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 19
Region 0: Memory at febffc00 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev
c2) (prog-if 00 [Normal decode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=64
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
00:1f.0 ISA bridge [0601]: Intel Corporation 82801EB/ER (ICH5/ICH5R) LPC
Interface Bridge [8086:24d0] (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:1f.1 IDE interface [0101]: Intel Corporation 82801EB/ER (ICH5/ICH5R) IDE
Controller [8086:24db] (rev 02) (prog-if 8a [Master SecP PriP])
Subsystem: ASUSTeK Computer Inc. P5P800-MX Mainboard [1043:80a6]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at fc00 [size=16]
Region 5: Memory at 30000000 (32-bit, non-prefetchable) [size=1K]
00:1f.3 SMBus [0c05]: Intel Corporation 82801EB/ER (ICH5/ICH5R) SMBus
Controller [8086:24d3] (rev 02)
Subsystem: ASUSTeK Computer Inc. P4P800 Mainboard [1043:80a6]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 20
Region 4: I/O ports at 0400 [size=32]
00:1f.5 Multimedia audio controller [0401]: Intel Corporation 82801EB/ER
(ICH5/ICH5R) AC'97 Audio Controller [8086:24d5] (rev 02)
Subsystem: ASUSTeK Computer Inc. Unknown device [1043:810d]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 20
Region 0: I/O ports at e800 [size=256]
Region 1: I/O ports at ee80 [size=64]
Region 2: Memory at febff800 (32-bit, non-prefetchable) [size=512]
Region 3: Memory at febff400 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:00.0 VGA compatible controller [0300]: nVidia Corporation NV34 [GeForce FX
5200] [10de:0322] (rev a1) (prog-if 00 [VGA])
Subsystem: ASUSTeK Computer Inc. Unknown device [1043:80cf]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (1250ns min, 250ns max)
Interrupt: pin A routed to IRQ 10
Region 0: Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at e8000000 (32-bit, prefetchable) [size=128M]
Expansion ROM at feae0000 [disabled] [size=128K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [44] AGP version 3.0
Status: RQ=32 Iso- ArqSz=0 Cal=3 SBA+ ITACoh- GART64- HTrans-
64bit- FW+ AGP3+ Rate=x4,x8
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW-
Rate=<none>
dmesg of 2.6.20-1:
==================
Linux version 2.6.20-1-686 (Debian 2.6.20-3) ([EMAIL PROTECTED]) (gcc version
4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #1 SMP Tue Apr 24 21:52:11 UTC
2007
BIOS-provided physical RAM map:
sanitize start
sanitize end
copy_e820_map() start: 0000000000000000 size: 000000000009fc00 end:
000000000009fc00 type: 1
copy_e820_map() type is E820_RAM
copy_e820_map() start: 000000000009fc00 size: 0000000000000400 end:
00000000000a0000 type: 2
copy_e820_map() start: 00000000000e8000 size: 0000000000018000 end:
0000000000100000 type: 2
copy_e820_map() start: 0000000000100000 size: 000000001fe30000 end:
000000001ff30000 type: 1
copy_e820_map() type is E820_RAM
copy_e820_map() start: 000000001ff30000 size: 0000000000010000 end:
000000001ff40000 type: 3
copy_e820_map() start: 000000001ff40000 size: 00000000000b0000 end:
000000001fff0000 type: 4
copy_e820_map() start: 000000001fff0000 size: 0000000000010000 end:
0000000020000000 type: 2
copy_e820_map() start: 00000000ffba0000 size: 0000000000460000 end:
0000000100000000 type: 2
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e8000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001ff30000 (usable)
BIOS-e820: 000000001ff30000 - 000000001ff40000 (ACPI data)
BIOS-e820: 000000001ff40000 - 000000001fff0000 (ACPI NVS)
BIOS-e820: 000000001fff0000 - 0000000020000000 (reserved)
BIOS-e820: 00000000ffba0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
511MB LOWMEM available.
found SMP MP-table at 000ff780
Entering add_active_range(0, 0, 130864) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 130864
HighMem 130864 -> 130864
early_node_map[1] active PFN ranges
0: 0 -> 130864
On node 0 totalpages: 130864
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 990 pages used for memmap
Normal zone: 125778 pages, LIFO batch:31
HighMem zone: 0 pages used for memmap
DMI 2.3 present.
ACPI: RSDP (v000 ACPIAM ) @ 0x000f9e70
ACPI: RSDT (v001 A M I OEMRSDT 0x02000424 MSFT 0x00000097) @ 0x1ff30000
ACPI: FADT (v002 A M I OEMFACP 0x02000424 MSFT 0x00000097) @ 0x1ff30200
ACPI: MADT (v001 A M I OEMAPIC 0x02000424 MSFT 0x00000097) @ 0x1ff30390
ACPI: OEMB (v001 A M I OEMBIOS 0x02000424 MSFT 0x00000097) @ 0x1ff40040
ACPI: DSDT (v001 P4PSS P4PSS023 0x00000023 INTL 0x02002026) @ 0x00000000
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:2 APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1 15:2 APIC version 20
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 30000000 (gap: 20000000:dfba0000)
Detected 2793.168 MHz processor.
Built 1 zonelists. Total pages: 129842
Kernel command line: root=/dev/hda7 ro
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 8192 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 508844k/523456k available (1641k kernel code, 14008k reserved, 619k
data, 208k init, 0k highmem)
virtual kernel memory layout:
fixmap : 0xfff4f000 - 0xfffff000 ( 704 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xe0800000 - 0xff7fe000 ( 495 MB)
lowmem : 0xc0000000 - 0xdff30000 ( 511 MB)
.init : 0xc033b000 - 0xc036f000 ( 208 kB)
.data : 0xc029a5e5 - 0xc03353b4 ( 619 kB)
.text : 0xc0100000 - 0xc029a5e5 (1641 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 5590.38 BogoMIPS (lpj=11180772)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400
00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
CPU: After all inits, caps: bfebfbff 00000000 00000000 00003080 00004400
00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU0: Thermal monitoring enabled
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
ACPI: Core revision 20060707
CPU0: Intel(R) Pentium(R) 4 CPU 2.80GHz stepping 09
SMP alternatives: switching to SMP code
Booting processor 1/1 eip 3000
Initializing CPU#1
Calibrating delay using timer specific routine.. 5586.38 BogoMIPS (lpj=11172775)
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400
00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
CPU: After all inits, caps: bfebfbff 00000000 00000000 00003080 00004400
00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel P4/Xeon Extended MCE MSRs (12) available
CPU1: Thermal monitoring enabled
CPU1: Intel(R) Pentium(R) 4 CPU 2.80GHz stepping 09
Total of 2 processors activated (11176.77 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
checking TSC synchronization across 2 CPUs: passed.
Brought up 2 CPUs
migration_cost=216
Booting paravirtualized kernel on bare hardware
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=2
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI quirk: region 0800-087f claimed by ICH4 ACPI/GPIO/TCO
PCI quirk: region 0480-04bf claimed by ICH4 GPIO
0000:00:1f.1: trying to change BAR0 from 0000 to 01F0
0000:00:1f.1: trying to change BAR1 from 0000 to 03F4
0000:00:1f.1: trying to change BAR2 from 0000 to 0170
0000:00:1f.1: trying to change BAR3 from 0000 to 0374
Boot video device is 0000:01:00.0
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs *3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 *11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 14 devices
ASUS P4P800 detected. Disabling PnPBIOS
PnPBIOS: Disabled
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
NET: Registered protocol family 8
NET: Registered protocol family 20
pnp: 00:0a: ioport range 0x680-0x6ff has been reserved
pnp: 00:0a: ioport range 0x290-0x297 has been reserved
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: fc900000-fe9fffff
PREFETCH window: e7f00000-f7efffff
PCI: Bridge: 0000:00:1e.0
IO window: d000-dfff
MEM window: fea00000-feafffff
PREFETCH window: disabled.
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 8192)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 6664k freed
audit: initializing netlink socket (disabled)
audit(1009843209.156:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
input: AT Translated Set 2 keyboard as /class/input/input0
Starting balanced_irq
Using IPI No-Shortcut mode
ACPI: (supports S0 S1 S3 S4 S5)
Freeing unused kernel memory: 208k freed
Time: tsc clocksource has been installed.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
8139cp 0000:02:05.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip
8139cp 0000:02:05.0: Try the "8139too" driver instead.
8139too Fast Ethernet driver 0.9.28
ACPI: PCI Interrupt 0000:02:05.0[A] -> GSI 22 (level, low) -> IRQ 16
eth0: RealTek RTL8139 at 0xd800, 00:0e:a6:d1:70:5d, IRQ 16
eth0: Identified 8139 chip type 'RTL-8100B/8139D'
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 17, io base 0x0000ef00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Floppy drive(s): fd0 is 1.44M
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 18, io base 0x0000ef20
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
FDC 0 is a post-1991 82077
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 19, io base 0x0000ef40
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.3[A] -> GSI 16 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: irq 17, io base 0x0000ef80
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 20, io mem 0xfebffc00
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
ICH5: IDE controller at PCI slot 0000:00:1f.1
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 19
ICH5: chipset revision 2
ICH5: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hda: SAMSUNG SP0802N, ATA DISK drive
hda: hw_config=600b
hda: hw_config=600b
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: HL-DT-ST DVDRAM GSA-4082B, ATAPI CD/DVD-ROM drive
hdd: HL-DT-ST GCE-8525B, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
SCSI subsystem initialized
libata version 2.00 loaded.
hda: max request size: 512KiB
hdc: ATAPI 32X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
hda: 156368016 sectors (80060 MB) w/2048KiB Cache, CHS=16383/255/63<6>hda:
hw_config=600b
, UDMA(100)
hda: cache flushes supported
hda:<6>hdd: ATAPI 52X CD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
hda1 hda2 < hda5 hda6 hda7 hda8 >
md: linear personality registered for level -1
md: multipath personality registered for level -4
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
raid5: automatically using best checksumming function: pIII_sse
pIII_sse : 3514.000 MB/sec
raid5: using function: pIII_sse (3514.000 MB/sec)
raid6: int32x1 828 MB/s
raid6: int32x2 849 MB/s
raid6: int32x4 753 MB/s
raid6: int32x8 519 MB/s
raid6: mmxx1 2241 MB/s
raid6: mmxx2 2436 MB/s
raid6: sse1x1 1151 MB/s
raid6: sse1x2 1958 MB/s
raid6: sse2x1 2130 MB/s
raid6: sse2x2 2810 MB/s
raid6: using algorithm sse2x2 (2810 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
md: raid10 personality registered for level 10
Attempting manual resume
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
input: PC Speaker as /class/input/input1
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
Real Time Clock Driver v1.12ac
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.01 (11-Nov-2006)
iTCO_wdt: Found a ICH5 or ICH5R TCO device (Version=1, TCOBASE=0x0860)
iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 3
[PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel 865 Chipset.
agpgart: AGP aperture is 64M @ 0xf8000000
ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 17 (level, low) -> IRQ 21
intel_rng: FWH not detected
parport0: Printer, HEWLETT-PACKARD DESKJET 710C
ACPI: PCI Interrupt 0000:00:1f.5[B] -> GSI 17 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:00:1f.5 to 64
intel8x0_measure_ac97_clock: measured 56110 usecs
intel8x0: clocking to 48000
input: ImExPS/2 Generic Explorer Mouse as /class/input/input2
Adding 1028120k swap on /dev/hda8. Priority:-1 extents:1 across:1028120k
EXT3 FS on hda7, internal journal
lp0: using parport0 (interrupt-driven).
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: [EMAIL PROTECTED]
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
dmesg of 2.6.22-3:
===================
Linux version 2.6.22-3-686 (Debian 2.6.22-6) ([EMAIL PROTECTED]) (gcc version
4.1.3 20071019 (prerelease) (Debian 4.1.2-17)) #1 SMP Mon Nov 12 08:32:57 UTC
2007
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e8000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001ff30000 (usable)
BIOS-e820: 000000001ff30000 - 000000001ff40000 (ACPI data)
BIOS-e820: 000000001ff40000 - 000000001fff0000 (ACPI NVS)
BIOS-e820: 000000001fff0000 - 0000000020000000 (reserved)
BIOS-e820: 00000000ffba0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
511MB LOWMEM available.
found SMP MP-table at 000ff780
Entering add_active_range(0, 0, 130864) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 130864
HighMem 130864 -> 130864
early_node_map[1] active PFN ranges
0: 0 -> 130864
On node 0 totalpages: 130864
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 990 pages used for memmap
Normal zone: 125778 pages, LIFO batch:31
HighMem zone: 0 pages used for memmap
DMI 2.3 present.
ACPI: RSDP 000F9E70, 0014 (r0 ACPIAM)
ACPI: RSDT 1FF30000, 0030 (r1 A M I OEMRSDT 2000424 MSFT 97)
ACPI: FACP 1FF30200, 0081 (r2 A M I OEMFACP 2000424 MSFT 97)
ACPI: DSDT 1FF303F0, 3779 (r1 P4PSS P4PSS023 23 INTL 2002026)
ACPI: FACS 1FF40000, 0040
ACPI: APIC 1FF30390, 005C (r1 A M I OEMAPIC 2000424 MSFT 97)
ACPI: OEMB 1FF40040, 003F (r1 A M I OEMBIOS 2000424 MSFT 97)
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:2 APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1 15:2 APIC version 20
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 30000000 (gap: 20000000:dfba0000)
Built 1 zonelists. Total pages: 129842
Kernel command line: root=/dev/hda7 ro
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 8192 bytes)
Detected 2793.191 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 508688k/523456k available (1687k kernel code, 14260k reserved, 646k
data, 244k init, 0k highmem)
virtual kernel memory layout:
fixmap : 0xfff4e000 - 0xfffff000 ( 708 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xe0800000 - 0xff7fe000 ( 495 MB)
lowmem : 0xc0000000 - 0xdff30000 ( 511 MB)
.init : 0xc034d000 - 0xc038a000 ( 244 kB)
.data : 0xc02a5f17 - 0xc03477e4 ( 646 kB)
.text : 0xc0100000 - 0xc02a5f17 (1687 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 5590.50 BogoMIPS (lpj=11181016)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400
00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
CPU: After all inits, caps: bfebfbff 00000000 00000000 0000b080 00004400
00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU0: Thermal monitoring enabled
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
ACPI: Core revision 20070126
CPU0: Intel(R) Pentium(R) 4 CPU 2.80GHz stepping 09
SMP alternatives: switching to SMP code
Booting processor 1/1 eip 3000
Initializing CPU#1
Calibrating delay using timer specific routine.. 5586.37 BogoMIPS (lpj=11172757)
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400
00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
CPU: After all inits, caps: bfebfbff 00000000 00000000 0000b080 00004400
00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel P4/Xeon Extended MCE MSRs (12) available
CPU1: Thermal monitoring enabled
CPU1: Intel(R) Pentium(R) 4 CPU 2.80GHz stepping 09
Total of 2 processors activated (11176.88 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Brought up 2 CPUs
migration_cost=142
Booting paravirtualized kernel on bare hardware
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=2
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI quirk: region 0800-087f claimed by ICH4 ACPI/GPIO/TCO
PCI quirk: region 0480-04bf claimed by ICH4 GPIO
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs *3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 *11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 14 devices
ACPI: ACPI bus type pnp unregistered
ASUS P4P800 detected. Disabling PnPBIOS
PnPBIOS: Disabled
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
NET: Registered protocol family 8
NET: Registered protocol family 20
ACPI: RTC can wake from S4
pnp: 00:0a: ioport range 0x680-0x6ff has been reserved
pnp: 00:0a: ioport range 0x290-0x297 has been reserved
pnp: 00:0b: iomem range 0xfed20000-0xfed8ffff has been reserved
pnp: 00:0b: iomem range 0xffb00000-0xffbfffff could not be reserved
pnp: 00:0c: iomem range 0xfec00000-0xfec00fff has been reserved
pnp: 00:0c: iomem range 0xfee00000-0xfee00fff has been reserved
pnp: 00:0d: iomem range 0x0-0x9ffff could not be reserved
pnp: 00:0d: iomem range 0xc0000-0xdffff could not be reserved
pnp: 00:0d: iomem range 0xe0000-0xfffff could not be reserved
pnp: 00:0d: iomem range 0x100000-0x1ffeffff could not be reserved
Time: tsc clocksource has been installed.
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: fca00000-feafffff
PREFETCH window: e7f00000-f7efffff
PCI: Bridge: 0000:00:1e.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 196608 bytes)
TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
checking if image is initramfs... it is
Switched to high resolution mode on CPU 0
Switched to high resolution mode on CPU 1
Freeing initrd memory: 6748k freed
audit: initializing netlink socket (disabled)
audit(1009843216.848:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Boot video device is 0000:01:00.0
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI No-Shortcut mode
Freeing unused kernel memory: 244k freed
input: AT Translated Set 2 keyboard as /class/input/input0
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 16, io base 0x0000ef00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Floppy drive(s): fd0 is 1.44M
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
FDC 0 is a post-1991 82077
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 17, io base 0x0000ef20
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000ef40
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.3[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000ef80
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 19, io mem 0xfebffc00
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
ICH5: IDE controller at PCI slot 0000:00:1f.1
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 18
ICH5: chipset revision 2
ICH5: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hda: SAMSUNG SP0802N, ATA DISK drive
hda: selected mode 0x45
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: HL-DT-ST DVDRAM GSA-4082B, ATAPI CD/DVD-ROM drive
hdd: HL-DT-ST GCE-8525B, ATAPI CD/DVD-ROM drive
hdc: selected mode 0x42
hdd: selected mode 0x42
ide1 at 0x170-0x177,0x376 on irq 15
SCSI subsystem initialized
libata version 2.21 loaded.
hdc: ATAPI 32X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
hda: max request size: 512KiB
hda: 156368016 sectors (80060 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(100)
hda: cache flushes supported
hda:<6>hdd: ATAPI 52X CD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
hda1 hda2 < hda5 hda6 hda7 hda8 >
md: linear personality registered for level -1
md: multipath personality registered for level -4
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
raid5: automatically using best checksumming function: pIII_sse
pIII_sse : 3500.000 MB/sec
raid5: using function: pIII_sse (3500.000 MB/sec)
raid6: int32x1 793 MB/s
raid6: int32x2 822 MB/s
raid6: int32x4 657 MB/s
raid6: int32x8 530 MB/s
raid6: mmxx1 2166 MB/s
raid6: mmxx2 2708 MB/s
raid6: sse1x1 1105 MB/s
raid6: sse1x2 2235 MB/s
raid6: sse2x1 1837 MB/s
raid6: sse2x2 3013 MB/s
raid6: using algorithm sse2x2 (3013 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
md: raid10 personality registered for level 10
Attempting manual resume
swsusp: Basic memory bitmaps created
swsusp: Basic memory bitmaps freed
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Real Time Clock Driver v1.12ac
input: PC Speaker as /class/input/input1
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.01 (21-Jan-2007)
iTCO_wdt: Found a ICH5 or ICH5R TCO device (Version=1, TCOBASE=0x0860)
iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
intel_rng: FWH not detected
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 17 (level, low) -> IRQ 20
Linux agpgart interface v0.102 (c) Dave Jones
agpgart: Detected an Intel 865 Chipset.
agpgart: AGP aperture is 64M @ 0xf8000000
parport_pc 00:09: reported by Plug and Play ACPI
parport0: PC-style at 0x378 (0x778), irq 7, dma 3
[PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
parport0: Printer, HEWLETT-PACKARD DESKJET 710C
ACPI: PCI Interrupt 0000:00:1f.5[B] -> GSI 17 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:1f.5 to 64
intel8x0_measure_ac97_clock: measured 52121 usecs
intel8x0: clocking to 48000
input: ImExPS/2 Generic Explorer Mouse as /class/input/input2
Adding 1028120k swap on /dev/hda8. Priority:-1 extents:1 across:1028120k
EXT3 FS on hda7, internal journal
lp0: using parport0 (interrupt-driven).
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: [EMAIL PROTECTED]
-- Package-specific info:
-- System Information:
Debian Release: lenny/sid
APT prefers unstable
APT policy: (500, 'unstable'), (500, 'stable'), (101, 'experimental')
Architecture: i386 (i686)
Kernel: Linux 2.6.20-1-686 (SMP w/2 CPU cores)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.22-3-686 depends on:
ii initramfs-tools [linux-initr 0.91c tools for generating an initramfs
ii module-init-tools 3.3-pre11-4 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.22-3-686 recommends:
ii libc6-i686 2.7-3 GNU C Library: Shared libraries [i
-- debconf information:
linux-image-2.6.22-3-686/postinst/bootloader-test-error-2.6.22-3-686:
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.22-3-686/preinst/lilo-initrd-2.6.22-3-686: true
linux-image-2.6.22-3-686/prerm/would-invalidate-boot-loader-2.6.22-3-686: true
linux-image-2.6.22-3-686/preinst/overwriting-modules-2.6.22-3-686: true
linux-image-2.6.22-3-686/preinst/elilo-initrd-2.6.22-3-686: true
linux-image-2.6.22-3-686/postinst/kimage-is-a-directory:
linux-image-2.6.22-3-686/preinst/lilo-has-ramdisk:
linux-image-2.6.22-3-686/preinst/initrd-2.6.22-3-686:
linux-image-2.6.22-3-686/postinst/old-initrd-link-2.6.22-3-686: true
linux-image-2.6.22-3-686/postinst/old-system-map-link-2.6.22-3-686: true
linux-image-2.6.22-3-686/preinst/already-running-this-2.6.22-3-686:
linux-image-2.6.22-3-686/postinst/depmod-error-2.6.22-3-686: false
linux-image-2.6.22-3-686/postinst/bootloader-error-2.6.22-3-686:
linux-image-2.6.22-3-686/preinst/failed-to-move-modules-2.6.22-3-686:
linux-image-2.6.22-3-686/postinst/old-dir-initrd-link-2.6.22-3-686: true
linux-image-2.6.22-3-686/preinst/abort-install-2.6.22-3-686:
linux-image-2.6.22-3-686/preinst/abort-overwrite-2.6.22-3-686:
linux-image-2.6.22-3-686/postinst/depmod-error-initrd-2.6.22-3-686: false
linux-image-2.6.22-3-686/preinst/bootloader-initrd-2.6.22-3-686: true
linux-image-2.6.22-3-686/prerm/removing-running-kernel-2.6.22-3-686: true
linux-image-2.6.22-3-686/postinst/create-kimage-link-2.6.22-3-686: true
--
To UNSUBSCRIBE, email to [EMAIL PROTECTED]
with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
