--- Begin Message ---
Package: linux-image-2.6.22-3-k7
Version: 2.6.22-6
Severity: important
Hello everyone,
since linux-image-2.6.22-3 I can't stop my notebook. It stops processing
at the last point "Will now halt". The only thing I can do is to press
enter and he will enter the next line, no errors / warnings or something
like that.
The problem doesn't exists for me in 2.6.22-2.
Note:
Unless my kernel is tainted or not, the problem occurs, I tested both.
-- Package-specific info:
** Version:
Linux version 2.6.22-3-k7 (Debian 2.6.22-6) ([EMAIL PROTECTED]) (gcc
version 4.1.3 20071019 (prerelease) (Debian 4.1.2-17)) #1 SMP Mon Nov 12
09:12:50 UTC 2007
** Tainted: P (1)
** Kernel log:
SB600_PATA: IDE controller at PCI slot 0000:00:14.1
ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 17
SB600_PATA: chipset revision 0
SB600_PATA: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x5040-0x5047, BIOS settings: hda:DMA, hdb:pio
Probing IDE interface ide0...
hda: HL-DT-ST DVDRAM GSA-T20L, ATAPI CD/DVD-ROM drive
hda: selected mode 0x22
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, DMA
Uniform CD-ROM driver Revision: 3.20
Attempting manual resume
swsusp: Basic memory bitmaps created
swsusp: Basic memory bitmaps freed
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Linux agpgart interface v0.102 (c) Dave Jones
Real Time Clock Driver v1.12ac
piix4_smbus 0000:00:14.0: Found 0000:00:14.0 device
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
Yenta: CardBus bridge found at 0000:02:04.0 [103c:30c2]
Yenta: ISA IRQ mask 0x0cb8, PCI irq 16
Socket status: 30000006
Yenta: Raising subordinate bus# of parent bus (#02) from #03 to #06
pcmcia: parent PCI bridge I/O window: 0x1000 - 0x1fff
cs: IO port probe 0x1000-0x1fff: clean.
pcmcia: parent PCI bridge Memory window: 0xd0100000 - 0xd01fffff
pcmcia: parent PCI bridge Memory window: 0x50000000 - 0x53ffffff
ACPI: PCI Interrupt 0000:00:14.2[A] -> GSI 16 (level, low) -> IRQ 17
cs: IO port probe 0x100-0x3af: clean.
cs: IO port probe 0x3e0-0x4ff: clean.
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: excluding 0xc00-0xc07 0xc10-0xc17
0xc50-0xc57 0xc68-0xc6f 0xcd0-0xcdf
cs: IO port probe 0xa00-0xaff: clean.
Synaptics Touchpad, model: 1, fw: 6.2, id: 0x2580b1, caps: 0xa04793/0x300000
serio: Synaptics pass-through port at isa0060/serio4/input0
input: SynPS/2 Synaptics TouchPad as /class/input/input1
si3054: cannot initialize. EXT MID = 0000
Adding 979956k swap on /dev/sda2. Priority:-1 extents:1 across:979956k
EXT3 FS on sda4, internal journal
loop: module loaded
ndiswrapper version 1.49 loaded (smp=yes, preempt=no)
ndiswrapper: driver bcmwl5 (Broadcom,10/12/2006, 4.100.15.5) loaded
ACPI: PCI Interrupt 0000:30:00.0[A] -> GSI 18 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:30:00.0 to 64
ndiswrapper: using IRQ 20
wlan0: ethernet device 00:1a:73:6f:57:8e using NDIS driver: bcmwl5,
version: 0x4640f05, NDIS version: 0x501, vendor: 'NDIS Network Adapter',
14E4:4312.5.conf
wlan0: encryption modes supported: WEP; TKIP with WPA, WPA2, WPA2PSK;
AES/CCMP with WPA, WPA2, WPA2PSK
usbcore: registered new interface driver ndiswrapper
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised:
[EMAIL PROTECTED]
fuse init (API version 7.8)
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on sda3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
PM: Writing back config space on device 0000:10:00.0 at offset c (was
cfff0000, writing 0)
powernow-k8: Found 2 AMD Turion(tm) 64 X2 Mobile Technology TL-56
processors (version 2.00.00)
powernow-k8: 0 : fid 0xa (1800 MHz), vid 0x12
powernow-k8: 1 : fid 0x8 (1600 MHz), vid 0x14
powernow-k8: 2 : fid 0x0 (800 MHz), vid 0x1e
powernow-k8: ph2 null fid transition 0xa
tg3: eth0: Link is up at 100 Mbps, full duplex.
tg3: eth0: Flow control is on for TX and on for RX.
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ACPI: Battery Slot [C1ED] (battery present)
ACPI: Battery Slot [C1EC] (battery absent)
ACPI: AC Adapter [C1EB] (off-line)
input: Power Button (FF) as /class/input/input2
ACPI: Power Button (FF) [PWRF]
input: Sleep Button (CM) as /class/input/input3
ACPI: Sleep Button (CM) [C28D]
input: Lid Switch as /class/input/input4
ACPI: Lid Switch [C265]
Clocksource tsc unstable (delta = -184497154 ns)
Bluetooth: Core ver 2.11
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
ADDRCONF(NETDEV_UP): wlan0: link is not ready
[fglrx] Maximum main memory to use for locked dma buffers: 804 MBytes.
[fglrx] ASYNCIO init succeed!
[fglrx] PAT is enabled successfully!
[fglrx] module loaded - fglrx 8.42.3 [Oct 19 2007] on minor 0
ACPI: PCI Interrupt 0000:01:05.0[B] -> GSI 19 (level, low) -> IRQ 21
[fglrx] GART Table is not in FRAME_BUFFER range
[fglrx] Reserve Block - 0 offset = 0X7ffb000 length = 0X5000
[fglrx] Reserve Block - 1 offset = 0X0 length = 0X1000000
eth0: no IPv6 routers present
APIC error on CPU0: 00(40)
APIC error on CPU1: 00(40)
** Loaded modules:
Module Size Used by
fglrx 1474412 9
rfcomm 37016 0
l2cap 23232 5 rfcomm
bluetooth 50148 4 rfcomm,l2cap
button 8208 0
ac 5508 0
battery 10308 0
ipv6 239524 12
powernow_k8 14976 1
cpufreq_userspace 4448 0
cpufreq_conservative 7176 0
cpufreq_powersave 2112 1
cpufreq_stats 5440 0
cpufreq_ondemand 8652 0
freq_table 4832 3 powernow_k8,cpufreq_stats,cpufreq_ondemand
fuse 42388 1
dm_snapshot 17252 0
dm_mirror 21376 0
dm_mod 52672 2 dm_snapshot,dm_mirror
ndiswrapper 176156 0
lm90 13604 0
loop 17412 0
joydev 9920 0
tsdev 8320 0
snd_hda_intel 239832 1
pcmcia 37548 0
firmware_class 9984 1 pcmcia
snd_pcm_oss 39904 0
snd_mixer_oss 15872 1 snd_pcm_oss
snd_pcm 72772 2 snd_hda_intel,snd_pcm_oss
snd_seq_dummy 4036 0
snd_seq_oss 29760 0
snd_seq_midi 8480 0
snd_rawmidi 23264 1 snd_seq_midi
snd_seq_midi_event 7360 2 snd_seq_oss,snd_seq_midi
snd_seq 46864 6
snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
snd_timer 21380 2 snd_pcm,snd_seq
snd_seq_device 8012 5
snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
yenta_socket 25100 1
rsrc_nonstatic 12288 1 yenta_socket
snd 48804 11
snd_hda_intel,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
pcmcia_core 37588 3 pcmcia,yenta_socket,rsrc_nonstatic
shpchp 31380 0
pci_hotplug 29568 1 shpchp
k8temp 5824 0
i2c_piix4 8844 0
rtc 13144 0
soundcore 7840 1 snd
evdev 9664 5
serio_raw 7044 0
psmouse 36432 0
i2c_core 24000 2 lm90,i2c_piix4
snd_page_alloc 10376 2 snd_hda_intel,snd_pcm
ati_agp 9036 0
agpgart 32264 2 fglrx,ati_agp
ext3 122696 3
jbd 55848 1 ext3
mbcache 8580 1 ext3
ide_cd 36896 0
cdrom 33184 1 ide_cd
generic 5124 0 [permanent]
atiixp 5968 0 [permanent]
ide_core 114436 3 ide_cd,generic,atiixp
sd_mod 27584 5
ehci_hcd 31116 0
ata_generic 7876 0
ohci_hcd 20036 0
ahci 21828 4
tg3 101124 0
usbcore 126024 4 ndiswrapper,ehci_hcd,ohci_hcd
libata 117232 2 ata_generic,ahci
scsi_mod 137356 2 sd_mod,libata
thermal 13768 0
processor 31560 2 powernow_k8,thermal
fan 5124 0
** PCI devices:
00:00.0 Host bridge [0600]: ATI Technologies Inc Unknown device [1002:7910]
Subsystem: Hewlett-Packard Company Unknown device [103c:30c2]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 64
00:01.0 PCI bridge [0604]: ATI Technologies Inc Unknown device
[1002:7912] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00004000-00004fff
Memory behind bridge: d0200000-d03fffff
Prefetchable memory behind bridge: 00000000c0000000-00000000c7ffffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
Capabilities: [44] HyperTransport: MSI Mapping
Capabilities: [b0] Subsystem: Hewlett-Packard Company Unknown device
[103c:30c2]
00:04.0 PCI bridge [0604]: ATI Technologies Inc Unknown device
[1002:7914] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=10, subordinate=10, sec-latency=0
Memory behind bridge: d0000000-d00fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag+
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 1
Link: Latency L0s <64ns, L1 <1us
Link: ASPM L1 Enabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
Slot: Number 0, PowerLimit 0.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Off, PwrInd Off, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit-
Queue=0/0 Enable-
Address: 00000000 Data: 0000
Capabilities: [b0] Subsystem: Hewlett-Packard Company Unknown device
[103c:30c2]
Capabilities: [b8] HyperTransport: MSI Mapping
Capabilities: [100] Virtual Channel
00:05.0 PCI bridge [0604]: ATI Technologies Inc Unknown device
[1002:7915] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=20, subordinate=20, sec-latency=0
I/O behind bridge: 00002000-00003fff
Memory behind bridge: cc000000-cfffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag+
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 247
Link: Latency L0s <64ns, L1 <1us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x16
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
Slot: Number 0, PowerLimit 0.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Off, PwrInd Off, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit-
Queue=0/0 Enable-
Address: 00000000 Data: 0000
Capabilities: [b0] Subsystem: Hewlett-Packard Company Unknown device
[103c:30c2]
Capabilities: [b8] HyperTransport: MSI Mapping
Capabilities: [100] Virtual Channel
00:06.0 PCI bridge [0604]: ATI Technologies Inc Unknown device
[1002:7916] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=30, subordinate=30, sec-latency=0
Memory behind bridge: c8000000-c80fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag+
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 3
Link: Latency L0s <64ns, L1 <1us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
Slot: Number 0, PowerLimit 0.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Off, PwrInd Off, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit-
Queue=0/0 Enable-
Address: 00000000 Data: 0000
Capabilities: [b0] Subsystem: Hewlett-Packard Company Unknown device
[103c:30c2]
Capabilities: [b8] HyperTransport: MSI Mapping
Capabilities: [100] Virtual Channel
00:12.0 SATA controller [0106]: ATI Technologies Inc SB600 Non-Raid-5
SATA [1002:4380] (prog-if 01 [AHCI 1.0])
Subsystem: ATI Technologies Inc SB600 Non-Raid-5 SATA [1002:4380]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at 9000 [size=8]
Region 1: I/O ports at 9008 [size=4]
Region 2: I/O ports at 9010 [size=8]
Region 3: I/O ports at 5018 [size=4]
Region 4: I/O ports at 5020 [size=16]
Region 5: Memory at d0409000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:13.0 USB Controller [0c03]: ATI Technologies Inc SB600 USB (OHCI0)
[1002:4387] (prog-if 10 [OHCI])
Subsystem: Hewlett-Packard Company Unknown device [103c:30c2]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at d0401000 (32-bit, non-prefetchable) [size=4K]
00:13.1 USB Controller [0c03]: ATI Technologies Inc SB600 USB (OHCI1)
[1002:4388] (prog-if 10 [OHCI])
Subsystem: Hewlett-Packard Company Unknown device [103c:30c2]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 19
Region 0: Memory at d0402000 (32-bit, non-prefetchable) [size=4K]
00:13.2 USB Controller [0c03]: ATI Technologies Inc SB600 USB (OHCI2)
[1002:4389] (prog-if 10 [OHCI])
Subsystem: Hewlett-Packard Company Unknown device [103c:30c2]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 19
Region 0: Memory at d0403000 (32-bit, non-prefetchable) [size=4K]
00:13.3 USB Controller [0c03]: ATI Technologies Inc SB600 USB (OHCI3)
[1002:438a] (prog-if 10 [OHCI])
Subsystem: Hewlett-Packard Company Unknown device [103c:30c2]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 19
Region 0: Memory at d0404000 (32-bit, non-prefetchable) [size=4K]
00:13.4 USB Controller [0c03]: ATI Technologies Inc SB600 USB (OHCI4)
[1002:438b] (prog-if 10 [OHCI])
Subsystem: Hewlett-Packard Company Unknown device [103c:30c2]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 19
Region 0: Memory at d0405000 (32-bit, non-prefetchable) [size=4K]
00:13.5 USB Controller [0c03]: ATI Technologies Inc SB600 USB Controller
(EHCI) [1002:4386] (prog-if 20 [EHCI])
Subsystem: Hewlett-Packard Company Unknown device [103c:30c2]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin D routed to IRQ 18
Region 0: Memory at d0406000 (32-bit, non-prefetchable) [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+
Capabilities: [e4] Debug port
00:14.0 SMBus [0c05]: ATI Technologies Inc SB600 SMBus [1002:4385] (rev 14)
Subsystem: Hewlett-Packard Company Unknown device [103c:30c2]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Region 0: I/O ports at 8200 [size=16]
Capabilities: [b0] HyperTransport: MSI Mapping
00:14.1 IDE interface [0101]: ATI Technologies Inc SB600 IDE [1002:438c]
(prog-if 82 [Master PriP])
Subsystem: Hewlett-Packard Company Unknown device [103c:30c2]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at 5040 [size=16]
00:14.2 Audio device [0403]: ATI Technologies Inc SB600 Azalia [1002:4383]
Subsystem: Hewlett-Packard Company Unknown device [103c:30c2]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin ? routed to IRQ 17
Region 0: Memory at 54000000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:14.3 ISA bridge [0601]: ATI Technologies Inc SB600 PCI to LPC Bridge
[1002:438d]
Subsystem: Hewlett-Packard Company Unknown device [103c:30c2]
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:14.4 PCI bridge [0604]: ATI Technologies Inc SB600 PCI to PCI Bridge
[1002:4384] (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop+ ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=02, subordinate=06, sec-latency=64
I/O behind bridge: 00001000-00001fff
Memory behind bridge: d0100000-d01fffff
Prefetchable memory behind bridge: 50000000-53ffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] K8
[Athlon64/Opteron] HyperTransport Technology Configuration [1022:1100]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Capabilities: [80] HyperTransport: Host or Secondary Interface
!!! Possibly incomplete decoding
Command: WarmRst+ DblEnd-
Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=8
Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
Revision ID: 1.02
00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] K8
[Athlon64/Opteron] Address Map [1022:1101]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] K8
[Athlon64/Opteron] DRAM Controller [1022:1102]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] K8
[Athlon64/Opteron] Miscellaneous Control [1022:1103]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Capabilities: [f0] #0f [0010]
01:05.0 VGA compatible controller [0300]: ATI Technologies Inc Unknown
device [1002:791f] (prog-if 00 [VGA])
Subsystem: Hewlett-Packard Company Unknown device [103c:30c2]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 21
Region 0: Memory at c0000000 (64-bit, prefetchable) [size=128M]
Region 2: Memory at d0200000 (64-bit, non-prefetchable) [size=64K]
Region 4: I/O ports at 4000 [size=256]
Region 5: Memory at d0300000 (32-bit, non-prefetchable) [size=1M]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit+
Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
02:04.0 CardBus bridge [0607]: Ricoh Co Ltd RL5c476 II [1180:0476] (rev b6)
Subsystem: Hewlett-Packard Company Unknown device [103c:30c2]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 168
Interrupt: pin A routed to IRQ 16
Region 0: Memory at d0100000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=02, secondary=03, subordinate=06, sec-latency=176
Memory window 0: 50000000-53fff000 (prefetchable)
Memory window 1: 58000000-5bfff000
I/O window 0: 00001000-000010ff
I/O window 1: 00001400-000014ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
10:00.0 Ethernet controller [0200]: Broadcom Corporation Unknown device
[14e4:1713] (rev 02)
Subsystem: Hewlett-Packard Company Unknown device [103c:30c2]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at d0000000 (64-bit, non-prefetchable) [size=64K]
Capabilities: [48] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Vital Product Data
Capabilities: [58] Vendor Specific Information
Capabilities: [e8] Message Signalled Interrupts: Mask- 64bit+
Queue=0/0 Enable-
Address: cfffeff7cfffeff4 Data: efd7
Capabilities: [d0] Express Endpoint IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag+
Device: Latency L0s <4us, L1 unlimited
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 4096 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 0
Link: Latency L0s <4us, L1 <64us
Link: ASPM L1 Enabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Capabilities: [100] Advanced Error Reporting
Capabilities: [13c] Virtual Channel
Capabilities: [160] Device Serial Number 53-54-5d-fe-ff-4b-1a-00
30:00.0 Network controller [0280]: Broadcom Corporation BCM4310 UART
[14e4:4312] (rev 02)
Subsystem: Hewlett-Packard Company Unknown device [103c:1371]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 20
Region 0: Memory at c8000000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
Capabilities: [58] Vendor Specific Information
Capabilities: [e8] Message Signalled Interrupts: Mask- 64bit+
Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [d0] Express Endpoint IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag+
Device: Latency L0s <4us, L1 unlimited
Device: AtnBtn+ AtnInd+ PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s, Port 0
Link: Latency L0s <4us, L1 <64us
Link: ASPM L0s L1 Enabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Capabilities: [100] Advanced Error Reporting
Capabilities: [13c] Virtual Channel
Capabilities: [160] Device Serial Number 1a-00-6f-ff-ff-73-8e-57
Capabilities: [16c] Power Budgeting
-- System Information:
Debian Release: lenny/sid
APT prefers unstable
APT policy: (500, 'unstable'), (500, 'testing')
Architecture: i386 (i686)
Kernel: Linux 2.6.22-3-k7 (SMP w/2 CPU cores)
Locale: LANG=de_DE.UTF-8, LC_CTYPE=de_DE.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.22-3-k7 depends on:
ii initramfs-tools [linux-initr 0.91b tools for generating an
initramfs
ii module-init-tools 3.3-pre11-4 tools for managing Linux
kernel mo
Versions of packages linux-image-2.6.22-3-k7 recommends:
ii libc6-i686 2.6.1-6 GNU C Library: Shared
libraries [i
-- debconf information:
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.22-3-k7/preinst/failed-to-move-modules-2.6.22-3-k7:
linux-image-2.6.22-3-k7/postinst/depmod-error-2.6.22-3-k7: false
linux-image-2.6.22-3-k7/preinst/lilo-has-ramdisk:
linux-image-2.6.22-3-k7/prerm/removing-running-kernel-2.6.22-3-k7: true
* linux-image-2.6.22-3-k7/preinst/already-running-this-2.6.22-3-k7:
linux-image-2.6.22-3-k7/prerm/would-invalidate-boot-loader-2.6.22-3-k7: true
linux-image-2.6.22-3-k7/postinst/old-system-map-link-2.6.22-3-k7: true
linux-image-2.6.22-3-k7/postinst/old-dir-initrd-link-2.6.22-3-k7: true
linux-image-2.6.22-3-k7/postinst/kimage-is-a-directory:
linux-image-2.6.22-3-k7/preinst/overwriting-modules-2.6.22-3-k7: true
linux-image-2.6.22-3-k7/postinst/create-kimage-link-2.6.22-3-k7: true
linux-image-2.6.22-3-k7/preinst/initrd-2.6.22-3-k7:
linux-image-2.6.22-3-k7/preinst/abort-install-2.6.22-3-k7:
linux-image-2.6.22-3-k7/preinst/lilo-initrd-2.6.22-3-k7: true
linux-image-2.6.22-3-k7/postinst/depmod-error-initrd-2.6.22-3-k7: false
linux-image-2.6.22-3-k7/postinst/old-initrd-link-2.6.22-3-k7: true
linux-image-2.6.22-3-k7/preinst/elilo-initrd-2.6.22-3-k7: true
linux-image-2.6.22-3-k7/postinst/bootloader-error-2.6.22-3-k7:
linux-image-2.6.22-3-k7/preinst/abort-overwrite-2.6.22-3-k7:
linux-image-2.6.22-3-k7/postinst/bootloader-test-error-2.6.22-3-k7:
linux-image-2.6.22-3-k7/preinst/bootloader-initrd-2.6.22-3-k7: true
--
Mit freundlichem Gruß / With kind regards,
Patrick Matthäi
E-Mail: [EMAIL PROTECTED]
Homepage: http://www.Linux-Dev.org/
--- End Message ---