Package: linux-image-2.6.26-1-amd64
Version: 2.6.26-13
Followup-For: Bug #501326
I am using suspend to disk.
The /sys/power/disk is set to platform and does not work when set to
shutdown either.
The PC powers off for a few seconds and then powers on again.
It does not work with 2.6.25 either. However, the problem started only
recently, suspend to disk used to work.
It is possible to power off by holding the power button or by booting
other system and powering off using that.
-- Package-specific info:
** Version:
Linux version 2.6.26-1-amd64 (Debian 2.6.26-13) (wa...@debian.org) (gcc version
4.1.3 20080704 (prerelease) (Debian 4.1.2-24)) #1 SMP Sat Jan 10 17:57:00 UTC
2009
** Command line:
BOOT_IMAGE=/boot/vmlinuz-2.6.26-1-amd64
root=UUID=ae7d5095-c8b3-4205-af0e-032b0e124ec3 ro
** Not tainted
** Kernel log:
[ 168.464445] PM: Writing back config space on device 0000:00:1b.0 at offset 1
(was 100006, writing 100002)
[ 168.464466] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 19 (level, low) ->
IRQ 19
[ 168.464473] PCI: Setting latency timer of device 0000:00:1b.0 to 64
[ 168.464542] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 168.464600] PCI: Setting latency timer of device 0000:00:1c.1 to 64
[ 168.464609] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 20 (level, low) ->
IRQ 20
[ 168.464615] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[ 168.464660] usb usb1: root hub lost power or was reset
[ 168.464678] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 17 (level, low) ->
IRQ 17
[ 168.464684] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[ 168.464734] usb usb2: root hub lost power or was reset
[ 168.464761] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) ->
IRQ 18
[ 168.464765] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[ 168.464804] usb usb3: root hub lost power or was reset
[ 168.464820] ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 19 (level, low) ->
IRQ 19
[ 168.464825] PCI: Setting latency timer of device 0000:00:1d.3 to 64
[ 168.464864] usb usb4: root hub lost power or was reset
[ 168.464889] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 20 (level, low) ->
IRQ 20
[ 168.464894] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[ 168.464931] usb usb5: root hub lost power or was reset
[ 168.468816] ehci_hcd 0000:00:1d.7: debug port 1
[ 168.468822] PCI: cache line size of 32 is not supported by device
0000:00:1d.7
[ 168.468856] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[ 168.468913] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) ->
IRQ 18
[ 168.468938] PM: Writing back config space on device 0000:00:1f.2 at offset 1
(was 2b00001, writing 2b00005)
[ 168.468951] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 17 (level, low) ->
IRQ 17
[ 168.468955] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[ 168.471738] ata2.01: _GTF evaluation failed (AE 0x1001)
[ 168.484447] PM: Writing back config space on device 0000:02:00.0 at offset 1
(was 100002, writing 100006)
[ 168.484476] ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 17 (level, low) ->
IRQ 17
[ 168.484484] PCI: Setting latency timer of device 0000:02:00.0 to 64
[ 168.492912] atl1 0000:02:00.0: eth0 link is up 100 Mbps full duplex
[ 168.561175] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[21]
MMIO=[cfeff800-cfefffff] Max Packet=[2048] IR/IT contexts=[4/8]
[ 168.568294] parport_pc 00:06: current resources: pnp_start_dev
[ 168.568297] parport_pc 00:06: irq 7 flags 0x401
[ 168.568299] parport_pc 00:06: dma 3 flags 0x800
[ 168.568301] parport_pc 00:06: io 0x378-0x37f flags 0x101
[ 168.568303] parport_pc 00:06: io 0x778-0x77f flags 0x101
[ 168.568306] parport_pc 00:06: set resources
[ 168.569714] parport_pc 00:06: encode 4 resources
[ 168.569718] parport_pc 00:06: encode irq 7 edge high exclusive (2-byte
descriptor)
[ 168.569721] parport_pc 00:06: encode dma 3 type 0x0 transfer 0x0 master 0
[ 168.569723] parport_pc 00:06: encode io 0x378-0x37f decode 0x1
[ 168.569725] parport_pc 00:06: encode io 0x778-0x77f decode 0x1
[ 168.570488] parport_pc 00:06: activated
[ 168.570495] serial 00:0d: current resources: pnp_start_dev
[ 168.570497] serial 00:0d: irq 4 flags 0x401
[ 168.570500] serial 00:0d: io 0x3f8-0x3ff flags 0x101
[ 168.570503] serial 00:0d: set resources
[ 168.571217] serial 00:0d: encode 3 resources
[ 168.571220] serial 00:0d: encode irq 4 edge high exclusive (2-byte
descriptor)
[ 168.571223] serial 00:0d: encode dma -1 type 0x0 transfer 0x0 master 0
[ 168.571225] serial 00:0d: encode io 0x3f8-0x3ff decode 0x1
[ 168.571929] serial 00:0d: activated
[ 168.643329] ata1.00: ACPI cmd ef/03:45:00:00:00:a0 filtered out
[ 168.643333] ata1.00: ACPI cmd ef/03:0c:00:00:00:a0 filtered out
[ 168.644014] ata1.00: ACPI cmd c6/00:10:00:00:00:a0 succeeded
[ 168.644014] ata1.00: ACPI cmd ef/90:06:00:00:00:00 succeeded
[ 168.658119] ata2.01: configured for UDMA/133
[ 168.658185] sd 1:0:1:0: [sdb] 156301488 512-byte hardware sectors (80026 MB)
[ 168.658209] sd 1:0:1:0: [sdb] Write Protect is off
[ 168.658213] sd 1:0:1:0: [sdb] Mode Sense: 00 3a 00 00
[ 168.658251] sd 1:0:1:0: [sdb] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 168.666807] ata1.00: configured for UDMA/133
[ 168.690772] ata1.00: configured for UDMA/133
[ 168.690775] ata1: EH complete
[ 168.690817] sd 0:0:0:0: [sda] 398297088 512-byte hardware sectors (203928 MB)
[ 168.690841] sd 0:0:0:0: [sda] Write Protect is off
[ 168.690844] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 168.690881] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 168.690916] sd 0:0:0:0: [sda] 398297088 512-byte hardware sectors (203928 MB)
[ 168.690938] sd 0:0:0:0: [sda] Write Protect is off
[ 168.690941] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 168.690978] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 169.452122] sd 0:0:0:0: [sda] Starting disk
[ 169.466005] sd 1:0:1:0: [sdb] Starting disk
[ 169.479474] hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4
[ 169.479656] hda: UDMA/66 mode selected
[ 169.479857] PCI: Setting latency timer of device 0000:00:02.0 to 64
[ 169.518667] Restarting tasks ... <6>usb 2-1: USB disconnect, address 4
[ 169.524031] done.
[ 169.856073] usb 2-1: new low speed USB device using uhci_hcd and address 5
[ 170.033258] usb 2-1: configuration #1 chosen from 1 choice
[ 170.064583] input: Tangtop Generic USBPS2 as /class/input/input10
[ 170.088156] input,hidraw0: USB HID v1.00 Keyboard [Tangtop Generic USBPS2]
on usb-0000:00:1d.1-1
[ 170.116894] input: Tangtop Generic USBPS2 as /class/input/input11
[ 170.160081] input,hidraw1: USB HID v1.00 Mouse [Tangtop Generic USBPS2] on
usb-0000:00:1d.1-1
[ 170.165312] usb 2-1: New USB device found, idVendor=0d3d, idProduct=0001
[ 170.165360] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 170.165400] usb 2-1: Product: Generic USBPS2
[ 170.165436] usb 2-1: Manufacturer: Tangtop
[ 170.165505] usb 4-2: USB disconnect, address 3
[ 170.432049] usb 4-2: new low speed USB device using uhci_hcd and address 4
[ 170.604023] usb 4-2: configuration #1 chosen from 1 choice
[ 170.624473] input: Logitech USB Trackball as /class/input/input12
[ 170.656083] input,hidraw2: USB HID v1.10 Mouse [Logitech USB Trackball] on
usb-0000:00:1d.3-2
[ 170.656326] usb 4-2: New USB device found, idVendor=046d, idProduct=c408
[ 170.656365] usb 4-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 170.656405] usb 4-2: Product: USB Trackball
[ 170.656441] usb 4-2: Manufacturer: Logitech
** Loaded modules:
Module Size Used by
i915 35072 2
drm 91488 3 i915
binfmt_misc 13580 1
ppdev 11656 0
lp 14724 0
ipv6 288328 24
reiserfs 211072 1
coretemp 11008 0
w83627ehf 26512 0
hwmon_vid 7296 1 w83627ehf
loop 19468 0
parport_pc 31016 1
parport 41776 3 ppdev,lp,parport_pc
psmouse 42268 0
serio_raw 9860 0
snd_hda_intel 434904 0
i2c_i801 13596 0
i2c_core 27936 1 i2c_i801
snd_pcm_oss 41760 0
snd_mixer_oss 18816 1 snd_pcm_oss
snd_pcm 81672 2 snd_hda_intel,snd_pcm_oss
rng_core 8968 0
iTCO_wdt 15696 0
snd_seq_dummy 7428 0
snd_seq_oss 33152 0
snd_seq_midi 11072 0
snd_rawmidi 26784 1 snd_seq_midi
snd_seq_midi_event 11904 2 snd_seq_oss,snd_seq_midi
snd_seq 54304 6
snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
snd_timer 25744 2 snd_pcm,snd_seq
snd_seq_device 11668 5
snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
snd 63688 9
snd_hda_intel,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
soundcore 12064 1 snd
snd_page_alloc 13072 2 snd_hda_intel,snd_pcm
button 11680 0
intel_agp 31728 1
joydev 14848 0
evdev 14208 5
ext3 125072 4
jbd 51240 1 ext3
mbcache 12804 1 ext3
ide_cd_mod 36360 0
cdrom 37928 1 ide_cd_mod
usbhid 45792 0
hid 41792 1 usbhid
ff_memless 9224 1 usbhid
sd_mod 29376 8
piix 12424 0 [permanent]
ide_pci_generic 9220 0 [permanent]
ide_core 128284 3 ide_cd_mod,piix,ide_pci_generic
ata_piix 22660 8
ohci1394 32564 0
ieee1394 93816 1 ohci1394
ata_generic 10116 0
libata 165472 2 ata_piix,ata_generic
scsi_mod 160760 2 sd_mod,libata
dock 14112 1 libata
ehci_hcd 36108 0
uhci_hcd 25760 0
atl1 35464 0
mii 9856 1 atl1
thermal 22688 0
processor 42304 1 thermal
fan 9352 0
thermal_sys 17728 3 thermal,processor,fan
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 82945G/GZ/P/PL Memory Controller
Hub [8086:2770] (rev 02)
Subsystem: ASUSTeK Computer Inc. Device [1043:817a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: agpgart-intel
Kernel modules: intel-agp
00:02.0 VGA compatible controller [0300]: Intel Corporation 82945G/GZ
Integrated Graphics Controller [8086:2772] (rev 02) (prog-if 00 [VGA
controller])
Subsystem: ASUSTeK Computer Inc. Device [1043:817a]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at cfd00000 (32-bit, non-prefetchable) [size=512K]
Region 1: I/O ports at 8800 [size=8]
Region 2: Memory at d0000000 (32-bit, prefetchable) [size=256M]
Region 3: Memory at cfd80000 (32-bit, non-prefetchable) [size=256K]
Capabilities: <access denied>
Kernel modules: intelfb
00:1b.0 Audio device [0403]: Intel Corporation 82801G (ICH7 Family) High
Definition Audio Controller [8086:27d8] (rev 01)
Subsystem: ASUSTeK Computer Inc. Device [1043:8249]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 16 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at cfdf8000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel
00:1c.0 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI Express
Port 1 [8086:27d0] (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 16 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:1c.1 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI Express
Port 2 [8086:27d2] (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 16 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: cff00000-cfffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:1d.0 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI
Controller #1 [8086:27c8] (rev 01) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. P5KPL-VM Motherboard [1043:8179]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 4: I/O ports at 9000 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.1 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI
Controller #2 [8086:27c9] (rev 01) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. P5KPL-VM Motherboard [1043:8179]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 4: I/O ports at 9400 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.2 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI
Controller #3 [8086:27ca] (rev 01) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. P5KPL-VM Motherboard [1043:8179]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at 9800 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.3 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI
Controller #4 [8086:27cb] (rev 01) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. P5KPL-VM Motherboard [1043:8179]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 19
Region 4: I/O ports at a000 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.7 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB2 EHCI
Controller [8086:27cc] (rev 01) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. P5KPL-VM Motherboard [1043:8179]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 0: Memory at cfdffc00 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev
e1) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: cfe00000-cfefffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation 82801GB/GR (ICH7 Family) LPC
Interface Bridge [8086:27b8] (rev 01)
Subsystem: ASUSTeK Computer Inc. P5KPL-VM Motherboard [1043:8179]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel modules: intel-rng, iTCO_wdt
00:1f.1 IDE interface [0101]: Intel Corporation 82801G (ICH7 Family) IDE
Controller [8086:27df] (rev 01) (prog-if 8a [Master SecP PriP])
Subsystem: ASUSTeK Computer Inc. P5KPL-VM Motherboard [1043:8179]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at ffa0 [size=16]
Kernel driver in use: PIIX_IDE
Kernel modules: ata_generic, ide-pci-generic, piix
00:1f.2 IDE interface [0101]: Intel Corporation 82801GB/GR/GH (ICH7 Family)
SATA IDE Controller [8086:27c0] (rev 01) (prog-if 8f [Master SecP SecO PriP
PriO])
Subsystem: ASUSTeK Computer Inc. Device [1043:2601]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 0: I/O ports at b800 [size=8]
Region 1: I/O ports at b400 [size=4]
Region 2: I/O ports at b000 [size=8]
Region 3: I/O ports at a800 [size=4]
Region 4: I/O ports at a400 [size=16]
Capabilities: <access denied>
Kernel driver in use: ata_piix
Kernel modules: ata_generic, ata_piix, ide-pci-generic
00:1f.3 SMBus [0c05]: Intel Corporation 82801G (ICH7 Family) SMBus Controller
[8086:27da] (rev 01)
Subsystem: ASUSTeK Computer Inc. P5KPL-VM Motherboard [1043:8179]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 17
Region 4: I/O ports at 0400 [size=32]
Kernel driver in use: i801_smbus
Kernel modules: i2c-i801
01:03.0 FireWire (IEEE 1394) [0c00]: VIA Technologies, Inc. VT6306 Fire II IEEE
1394 OHCI Link Layer Controller [1106:3044] (rev c0) (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:81fe]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (8000ns max), Cache Line Size: 16 bytes
Interrupt: pin A routed to IRQ 21
Region 0: Memory at cfeff800 (32-bit, non-prefetchable) [size=2K]
Region 1: I/O ports at c800 [size=128]
Capabilities: <access denied>
Kernel driver in use: ohci1394
Kernel modules: ohci1394
02:00.0 Ethernet controller [0200]: Attansic Technology Corp. L1 Gigabit
Ethernet Adapter [1969:1048] (rev b0)
Subsystem: ASUSTeK Computer Inc. Device [1043:8226]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 16 bytes
Interrupt: pin A routed to IRQ 1277
Region 0: Memory at cffc0000 (64-bit, non-prefetchable) [size=256K]
Expansion ROM at cffa0000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: atl1
Kernel modules: atl1
-- System Information:
Debian Release: 5.0
APT prefers testing
APT policy: (990, 'testing'), (500, 'unstable'), (1, 'experimental')
Architecture: amd64 (x86_64)
Kernel: Linux 2.6.26-1-amd64 (SMP w/1 CPU core)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.26-1-amd64 depends on:
ii debconf [debconf-2.0] 1.5.24 Debian configuration management sy
ii initramfs-tools [linux-initra 0.92o tools for generating an initramfs
ii module-init-tools 3.4-1 tools for managing Linux kernel mo
linux-image-2.6.26-1-amd64 recommends no packages.
Versions of packages linux-image-2.6.26-1-amd64 suggests:
ii grub-pc [grub] 1.96+20080724-12 GRand Unified Bootloader, version
pn linux-doc-2.6.26 <none> (no description available)
-- debconf-show failed
--
To UNSUBSCRIBE, email to debian-kernel-requ...@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org
