Package: linux-image-2.6.29-1-686
Version: 2.6.29-3
Severity: normal
As the drivers-ata-ata_piix-postpone-pata.patch removes the ability to
hot-swap a CD-ROM from a laptop media bay for several chipsets, please
consider building a flavour of the linux kernel that does not include that
patch, so that those of us with this problem can make the choice to install
a functional kernel, while not breaking operation for other users. Or,
perhaps create a package with only a functional ata_piix module that then
creates a diversion for those of us that wish it.
-- Package-specific info:
** Version:
Linux version 2.6.29-1-686 (Debian 2.6.29-3) (m...@debian.org) (gcc version
4.3.3 (Debian 4.3.3-3) ) #1 SMP Fri May 1 16:55:14 MDT 2009
** Command line:
root=/dev/sda2 ro
** Not tainted
** Kernel log:
[ 131.158904] tg3 0000:09:00.0: PME# disabled
[ 131.159061] tg3 0000:09:00.0: irq 29 for MSI/MSI-X
[ 131.220093] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 131.676985] iwlagn 0000:0c:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 131.677170] iwlagn 0000:0c:00.0: restoring config space at offset 0x1 (was
0x100102, writing 0x100106)
[ 131.677349] iwlagn 0000:0c:00.0: irq 30 for MSI/MSI-X
[ 131.677466] iwlagn 0000:0c:00.0: firmware: requesting iwlwifi-4965-2.ucode
[ 131.722237] iwlagn loaded firmware version 228.57.2.23
[ 131.928281] Registered led device: iwl-phy0:radio
[ 131.928322] Registered led device: iwl-phy0:assoc
[ 131.928363] Registered led device: iwl-phy0:RX
[ 131.928397] Registered led device: iwl-phy0:TX
[ 131.975445] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 132.797707] tg3: eth0: Link is up at 100 Mbps, full duplex.
[ 132.797716] tg3: eth0: Flow control is on for TX and on for RX.
[ 132.798178] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 134.317998] Ethernet Channel Bonding Driver: v3.5.0 (November 4, 2008)
[ 134.318009] bonding: Warning: either miimon or arp_interval and
arp_ip_target module parameters must be specified, otherwise bonding will not
detect link failures! see bonding.txt for details.
[ 134.405547] tg3 0000:09:00.0: PME# enabled
[ 134.422824] bonding: bond0: doing slave updates when interface is down.
[ 134.422835] bonding: bond0: Adding slave eth0.
[ 134.422842] bonding bond0: master_dev is not up in bond_enslave
[ 134.432279] tg3 0000:09:00.0: PME# disabled
[ 134.452311] tg3 0000:09:00.0: irq 29 for MSI/MSI-X
[ 134.513330] bonding: bond0: enslaving eth0 as an active interface with an up
link.
[ 134.607904] iwlagn 0000:0c:00.0: PCI INT A disabled
[ 134.615728] bonding: bond0: doing slave updates when interface is down.
[ 134.615739] bonding: bond0: Adding slave wlan0.
[ 134.615746] bonding bond0: master_dev is not up in bond_enslave
[ 134.629235] iwlagn 0000:0c:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 134.629381] iwlagn 0000:0c:00.0: restoring config space at offset 0x1 (was
0x100102, writing 0x100106)
[ 134.629555] iwlagn 0000:0c:00.0: irq 30 for MSI/MSI-X
[ 134.831809] Registered led device: iwl-phy0:radio
[ 134.831851] Registered led device: iwl-phy0:assoc
[ 134.831885] Registered led device: iwl-phy0:RX
[ 134.831922] Registered led device: iwl-phy0:TX
[ 134.868001] bonding: bond0: Warning: failed to get speed and duplex from
wlan0, assumed to be 100Mb/sec and Full.
[ 134.868038] bonding: bond0: enslaving wlan0 as an active interface with an
up link.
[ 134.868540] bonding: bond0: setting mode to active-backup (1).
[ 134.868731] bonding: bond0: Setting MII monitoring interval to 100.
[ 134.872326] bonding: bond0: Setting eth0 as primary slave.
[ 135.181128] tun: Universal TUN/TAP device driver, 1.6
[ 135.181136] tun: (C) 1999-2004 Max Krasnyansky <m...@qualcomm.com>
[ 135.475624] Bridge firewalling registered
[ 135.502099] device bond0 entered promiscuous mode
[ 135.508513] bonding: bond0: link status definitely down for interface eth0,
disabling it
[ 135.508522] bonding: bond0: link status definitely down for interface wlan0,
disabling it
[ 135.518072] device tap0 entered promiscuous mode
[ 135.524841] br0: port 2(tap0) entering learning state
[ 136.070066] tg3: eth0: Link is up at 100 Mbps, full duplex.
[ 136.070074] tg3: eth0: Flow control is on for TX and on for RX.
[ 136.108167] bonding: bond0: link status definitely up for interface eth0.
[ 136.108178] bonding: bond0: making interface eth0 the new active one.
[ 136.108184] device eth0 entered promiscuous mode
[ 136.108267] bonding: bond0: first active interface up!
[ 136.320612] br0: port 1(bond0) entering learning state
[ 138.139846] wlan0: authenticate with AP 00:1c:10:41:cd:9e
[ 138.142005] wlan0: authenticated
[ 138.142014] wlan0: associate with AP 00:1c:10:41:cd:9e
[ 138.145821] wlan0: RX AssocResp from 00:1c:10:41:cd:9e (capab=0x431 status=0
aid=1)
[ 138.145828] wlan0: associated
[ 138.208173] bonding: bond0: link status definitely up for interface wlan0.
[ 145.556152] br0: no IPv6 routers present
[ 145.592142] bond0: no IPv6 routers present
[ 145.661139] tap0: no IPv6 routers present
[ 150.524145] br0: topology change detected, propagating
[ 150.524157] br0: port 2(tap0) entering forwarding state
[ 151.320151] br0: topology change detected, propagating
[ 151.320164] br0: port 1(bond0) entering forwarding state
[ 2001.520092] CE: hpet increasing min_delta_ns to 15000 nsec
[35895.832172] CE: hpet increasing min_delta_ns to 22500 nsec
[37603.793451] usb 1-3.1.3: new high speed USB device using ehci_hcd and
address 7
[37603.901361] usb 1-3.1.3: New USB device found, idVendor=054c, idProduct=035b
[37603.901371] usb 1-3.1.3: New USB device strings: Mfr=1, Product=2,
SerialNumber=3
[37603.901377] usb 1-3.1.3: Product: WALKMAN
[37603.901381] usb 1-3.1.3: Manufacturer: Sony
[37603.901386] usb 1-3.1.3: SerialNumber: 10F9EE75026599
[37603.901582] usb 1-3.1.3: configuration #1 chosen from 1 choice
[37604.801423] Initializing USB Mass Storage driver...
[37604.801746] scsi5 : SCSI emulation for USB Mass Storage devices
[37604.801929] usbcore: registered new interface driver usb-storage
[37604.801932] USB Mass Storage support registered.
[37604.802263] usb-storage: device found at 7
[37604.802266] usb-storage: waiting for device to settle before scanning
[37609.801395] usb-storage: device scan complete
[37609.805487] scsi 5:0:0:0: Direct-Access SONY WALKMAN 1.10
PQ: 0 ANSI: 0 CCS
[37610.824529] ready
[37610.825022] sd 5:0:0:0: [sdb] 7737344 2048-byte hardware sectors: (15.8
GB/14.7 GiB)
[37610.826262] sd 5:0:0:0: [sdb] Write Protect is off
[37610.826269] sd 5:0:0:0: [sdb] Mode Sense: 00 3e 00 00
[37610.826274] sd 5:0:0:0: [sdb] Assuming drive cache: write through
[37610.828992] sd 5:0:0:0: [sdb] 7737344 2048-byte hardware sectors: (15.8
GB/14.7 GiB)
[37610.939642] sd 5:0:0:0: [sdb] Write Protect is off
[37610.939653] sd 5:0:0:0: [sdb] Mode Sense: 00 3e 00 00
[37610.939658] sd 5:0:0:0: [sdb] Assuming drive cache: write through
[37610.939667] sdb: sdb1
[37610.941449] sdb: p1 size 4294967292 limited to end of disk
[37610.947093] sd 5:0:0:0: [sdb] Attached SCSI removable disk
[37610.947247] sd 5:0:0:0: Attached scsi generic sg2 type 0
[84628.361975] FAT: utf8 is not a recommended IO charset for FAT filesystems,
filesystem will be case sensitive!
** Loaded modules:
Module Size Used by
nls_utf8 1472 1
nls_cp437 5304 1
vfat 8640 1
fat 41560 1 vfat
nls_base 6508 4 nls_utf8,nls_cp437,vfat,fat
usb_storage 83384 1
bridge 39732 0
stp 2092 1 bridge
tun 9620 1
bonding 74524 0
i915 129232 2
drm 133072 3 i915
i2c_algo_bit 4888 1 i915
rfcomm 29576 0
hidp 12064 2
l2cap 17076 10 rfcomm,hidp
vboxnetflt 69472 0
vboxdrv 94088 1 vboxnetflt
ipv6 231868 21 bonding
ppdev 6224 0
lp 7876 0
binfmt_misc 7136 1
acpi_cpufreq 6868 0
cpufreq_conservative 5456 0
cpufreq_stats 3588 0
cpufreq_powersave 1276 0
kvm_intel 38760 0
kvm 130584 1 kvm_intel
cpufreq_userspace 2716 0
fuse 48132 3
i8k 5320 0
loop 12952 0
snd_hda_codec_idt 48776 1
snd_hda_intel 22096 5
snd_hda_codec 58812 2 snd_hda_codec_idt,snd_hda_intel
snd_hwdep 6000 1 snd_hda_codec
snd_pcm_oss 31720 0
snd_mixer_oss 12000 3 snd_pcm_oss
snd_pcm 62712 3 snd_hda_intel,snd_hda_codec,snd_pcm_oss
snd_seq_dummy 2372 0
snd_seq_oss 24692 0
snd_seq_midi 5448 0
snd_rawmidi 18544 1 snd_seq_midi
hid_gaff 2900 0
hid_pl 2996 0
hid_cypress 2340 0
hid_zpff 2652 0
hid_gyration 2196 0
hid_sony 2568 0
hid_ntrig 1744 0
arc4 1544 2
snd_seq_midi_event 6072 2 snd_seq_oss,snd_seq_midi
ecb 2352 2
hid_samsung 2112 0
hid_microsoft 3200 0
hid_tmff 3460 0
hid_monterey 2132 0
snd_seq 41992 6
snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
joydev 8560 0
hid_ezkey 1832 0
iwlagn 70436 0
snd_timer 17776 2 snd_pcm,snd_seq
hid_apple 5704 0
iwlcore 76528 1 iwlagn
snd_seq_device 6108 5
snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
hid_a4tech 2500 0
hid_logitech 6624 0
ff_memless 4264 5 hid_gaff,hid_pl,hid_zpff,hid_tmff,hid_logitech
hid_cherry 2100 0
hid_sunplus 1972 0
led_class 3668 1 iwlcore
pcmcia 23320 0
mac80211 134572 2 iwlagn,iwlcore
dell_laptop 3148 0
rfkill 9544 5 iwlcore,dell_laptop
snd 48396 18
snd_hda_codec_idt,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
hid_petalynx 2468 0
hid_belkin 2284 0
hid_chicony 2004 0
usbhid 29036 5 hid_gaff,hid_pl,hid_zpff,hid_tmff,hid_logitech
btusb 10156 2
i2c_i801 8104 0
soundcore 6204 3 snd
psmouse 36596 0
hid 34192 22
hidp,hid_gaff,hid_pl,hid_cypress,hid_zpff,hid_gyration,hid_sony,hid_ntrig,hid_samsung,hid_microsoft,hid_tmff,hid_monterey,hid_ezkey,hid_apple,hid_a4tech,hid_logitech,hid_cherry,hid_sunplus,hid_petalynx,hid_belkin,hid_chicony,usbhid
bluetooth 46020 8 rfcomm,hidp,l2cap,btusb
cfg80211 32768 3 iwlagn,iwlcore,mac80211
i2c_core 20796 4 i915,drm,i2c_algo_bit,i2c_i801
yenta_socket 21244 1
rsrc_nonstatic 9424 1 yenta_socket
pcmcia_core 30756 3 pcmcia,yenta_socket,rsrc_nonstatic
snd_page_alloc 7976 2 snd_hda_intel,snd_pcm
dcdbas 6696 1 dell_laptop
pcspkr 2092 0
video 16356 0
output 2504 1 video
evdev 8164 15
serio_raw 4544 0
wmi 6332 0
parport_pc 22024 1
parport 30836 3 ppdev,lp,parport_pc
button 5672 0
battery 5832 0
ac 2872 0
ext3 106852 2
jbd 42280 1 ext3
mbcache 7184 1 ext3
sg 19504 0
sr_mod 12840 0
cdrom 29804 1 sr_mod
ide_pci_generic 3408 0
ide_core 91528 1 ide_pci_generic
ata_generic 4316 0
sd_mod 28188 6
crc_t10dif 1616 1 sd_mod
ata_piix 21280 0
firewire_ohci 18588 0
firewire_core 33332 1 firewire_ohci
crc_itu_t 1796 1 firewire_core
ahci 27540 3
libata 148672 3 ata_generic,ata_piix,ahci
scsi_mod 131852 5 usb_storage,sg,sr_mod,sd_mod,libata
uhci_hcd 19328 0
tg3 90916 0
libphy 19388 1 tg3
ehci_hcd 29708 0
usbcore 124716 7
usb_storage,hid_sony,usbhid,btusb,uhci_hcd,ehci_hcd
intel_agp 22548 1
agpgart 30624 3 drm,intel_agp
thermal 15064 0
processor 39476 4 acpi_cpufreq,thermal
fan 4104 0
thermal_sys 10272 4 video,thermal,processor,fan
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation Mobile PM965/GM965/GL960 Memory
Controller Hub [8086:2a00] (rev 0c)
Subsystem: Dell Device [1028:01f9]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: agpgart-intel
00:02.0 VGA compatible controller [0300]: Intel Corporation Mobile GM965/GL960
Integrated Graphics Controller [8086:2a02] (rev 0c) (prog-if 00 [VGA
controller])
Subsystem: Dell Latitude D630 [1028:01f9]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 28
Region 0: Memory at f6e00000 (64-bit, non-prefetchable) [size=1M]
Region 2: Memory at e0000000 (64-bit, prefetchable) [size=256M]
Region 4: I/O ports at eff8 [size=8]
Expansion ROM at <unassigned> [disabled]
Capabilities: <access denied>
00:02.1 Display controller [0380]: Intel Corporation Mobile GM965/GL960
Integrated Graphics Controller [8086:2a03] (rev 0c)
Subsystem: Dell Device [1028:01f9]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at f6f00000 (64-bit, non-prefetchable) [size=1M]
Capabilities: <access denied>
00:1a.0 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI
Controller #4 [8086:2834] (rev 02) (prog-if 00 [UHCI])
Subsystem: Dell Device [1028:01f9]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 4: I/O ports at 6f20 [size=32]
Kernel driver in use: uhci_hcd
00:1a.1 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI
Controller #5 [8086:2835] (rev 02) (prog-if 00 [UHCI])
Subsystem: Dell Device [1028:01f9]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at 6f00 [size=32]
Kernel driver in use: uhci_hcd
00:1a.7 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB2 EHCI
Controller #2 [8086:283a] (rev 02) (prog-if 20 [EHCI])
Subsystem: Dell Device [1028:01f9]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 22
Region 0: Memory at fed1c400 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1b.0 Audio device [0403]: Intel Corporation 82801H (ICH8 Family) HD Audio
Controller [8086:284b] (rev 02)
Subsystem: Dell Dell Latitude D630 [1028:01f9]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 21
Region 0: Memory at f6dfc000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
00:1c.0 PCI bridge [0604]: Intel Corporation 82801H (ICH8 Family) PCI Express
Port 1 [8086:283f] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=0b, subordinate=0b, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
00:1c.1 PCI bridge [0604]: Intel Corporation 82801H (ICH8 Family) PCI Express
Port 2 [8086:2841] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=0c, subordinate=0c, sec-latency=0
Memory behind bridge: f6c00000-f6cfffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
00:1c.5 PCI bridge [0604]: Intel Corporation 82801H (ICH8 Family) PCI Express
Port 6 [8086:2849] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=09, subordinate=09, sec-latency=0
Memory behind bridge: f6b00000-f6bfffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
00:1d.0 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI
Controller #1 [8086:2830] (rev 02) (prog-if 00 [UHCI])
Subsystem: Dell Device [1028:01f9]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 4: I/O ports at 6f80 [size=32]
Kernel driver in use: uhci_hcd
00:1d.1 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI
Controller #2 [8086:2831] (rev 02) (prog-if 00 [UHCI])
Subsystem: Dell Device [1028:01f9]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at 6f60 [size=32]
Kernel driver in use: uhci_hcd
00:1d.2 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI
Controller #3 [8086:2832] (rev 02) (prog-if 00 [UHCI])
Subsystem: Dell Device [1028:01f9]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 22
Region 4: I/O ports at 6f40 [size=32]
Kernel driver in use: uhci_hcd
00:1d.7 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB2 EHCI
Controller #1 [8086:2836] (rev 02) (prog-if 20 [EHCI])
Subsystem: Dell Device [1028:01f9]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 0: Memory at fed1c000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge
[8086:2448] (rev f2) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=03, subordinate=07, sec-latency=32
I/O behind bridge: 00002000-00002fff
Memory behind bridge: f6a00000-f6afffff
Prefetchable memory behind bridge: 0000000088000000-000000008bffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR+
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation 82801HEM (ICH8M) LPC Interface
Controller [8086:2815] (rev 02)
Subsystem: Dell Device [1028:01f9]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:1f.1 IDE interface [0101]: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E)
IDE Controller [8086:2850] (rev 02) (prog-if 8a [Master SecP PriP])
Subsystem: Dell Device [1028:01f9]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at 6fa0 [size=16]
Kernel driver in use: ata_piix
00:1f.2 SATA controller [0106]: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E)
SATA AHCI Controller [8086:2829] (rev 02) (prog-if 01 [AHCI 1.0])
Subsystem: Dell Device [1028:01f9]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 27
Region 0: I/O ports at 6eb0 [size=8]
Region 1: I/O ports at 6eb8 [size=4]
Region 2: I/O ports at 6ec0 [size=8]
Region 3: I/O ports at 6ec8 [size=4]
Region 4: I/O ports at 6ee0 [size=32]
Region 5: Memory at f6dfb800 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: ahci
00:1f.3 SMBus [0c05]: Intel Corporation 82801H (ICH8 Family) SMBus Controller
[8086:283e] (rev 02)
Subsystem: Dell Device [1028:01f9]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 17
Region 0: Memory at f6dfb700 (32-bit, non-prefetchable) [size=256]
Region 4: I/O ports at 10c0 [size=32]
Kernel driver in use: i801_smbus
03:01.0 CardBus bridge [0607]: O2 Micro, Inc. Cardbus bridge [1217:7135] (rev
21)
Subsystem: Dell Device [1028:01f9]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 168
Interrupt: pin A routed to IRQ 19
Region 0: Memory at f6a00000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=03, secondary=04, subordinate=07, sec-latency=176
Memory window 0: 88000000-8bfff000 (prefetchable)
Memory window 1: 8c000000-8ffff000
I/O window 0: 00002000-000020ff
I/O window 1: 00002400-000024ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
Kernel driver in use: yenta_cardbus
03:01.4 FireWire (IEEE 1394) [0c00]: O2 Micro, Inc. Firewire (IEEE 1394)
[1217:00f7] (rev 02) (prog-if 10 [OHCI])
Subsystem: Dell Device [1028:01f9]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx+
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at f6aff000 (32-bit, non-prefetchable) [size=4K]
Region 1: Memory at f6afe800 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: firewire_ohci
09:00.0 Ethernet controller [0200]: Broadcom Corporation NetXtreme BCM5755M
Gigabit Ethernet PCI Express [14e4:1673] (rev 02)
Subsystem: Dell Device [1028:01f9]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 29
Region 0: Memory at f6bf0000 (64-bit, non-prefetchable) [size=64K]
Expansion ROM at <ignored> [disabled]
Capabilities: <access denied>
Kernel driver in use: tg3
0c:00.0 Network controller [0280]: Intel Corporation PRO/Wireless 4965 AG or
AGN [Kedron] Network Connection [8086:4229] (rev 61)
Subsystem: Intel Corporation Device [8086:1120]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 30
Region 0: Memory at f6cfe000 (64-bit, non-prefetchable) [size=8K]
Capabilities: <access denied>
Kernel driver in use: iwlagn
-- System Information:
Debian Release: squeeze/sid
APT prefers testing
APT policy: (500, 'testing'), (500, 'stable')
Architecture: i386 (i686)
Kernel: Linux 2.6.29-1-686 (SMP w/2 CPU cores)
Locale: LANG=C, LC_CTYPE=en_CA.iso8859-1 (charmap=ISO-8859-1)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.29-1-686 depends on:
ii debconf [debconf-2.0] 1.5.26 Debian configuration management sy
ii initramfs-tools [linux-initra 0.93.2 tools for generating an initramfs
ii module-init-tools 3.7-pre9-1 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.29-1-686 recommends:
ii libc6-i686 2.9-4 GNU C Library: Shared libraries [i
Versions of packages linux-image-2.6.29-1-686 suggests:
ii grub 0.97-53 GRand Unified Bootloader (Legacy v
pn linux-doc-2.6.29 <none> (no description available)
-- debconf information:
linux-image-2.6.29-1-686/preinst/abort-overwrite-2.6.29-1-686:
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.29-1-686/preinst/overwriting-modules-2.6.29-1-686: true
linux-image-2.6.29-1-686/preinst/elilo-initrd-2.6.29-1-686: true
linux-image-2.6.29-1-686/preinst/initrd-2.6.29-1-686:
linux-image-2.6.29-1-686/preinst/bootloader-initrd-2.6.29-1-686: true
linux-image-2.6.29-1-686/postinst/bootloader-test-error-2.6.29-1-686:
linux-image-2.6.29-1-686/postinst/depmod-error-initrd-2.6.29-1-686: false
linux-image-2.6.29-1-686/prerm/removing-running-kernel-2.6.29-1-686: true
linux-image-2.6.29-1-686/preinst/lilo-has-ramdisk:
linux-image-2.6.29-1-686/postinst/old-system-map-link-2.6.29-1-686: true
linux-image-2.6.29-1-686/postinst/kimage-is-a-directory:
linux-image-2.6.29-1-686/postinst/old-dir-initrd-link-2.6.29-1-686: true
linux-image-2.6.29-1-686/preinst/lilo-initrd-2.6.29-1-686: true
linux-image-2.6.29-1-686/postinst/depmod-error-2.6.29-1-686: false
linux-image-2.6.29-1-686/postinst/bootloader-error-2.6.29-1-686:
linux-image-2.6.29-1-686/preinst/failed-to-move-modules-2.6.29-1-686:
linux-image-2.6.29-1-686/postinst/create-kimage-link-2.6.29-1-686: true
linux-image-2.6.29-1-686/prerm/would-invalidate-boot-loader-2.6.29-1-686: true
linux-image-2.6.29-1-686/preinst/abort-install-2.6.29-1-686:
linux-image-2.6.29-1-686/postinst/old-initrd-link-2.6.29-1-686: true
--
To UNSUBSCRIBE, email to debian-kernel-requ...@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org
