Package: linux-2.6 Version: 2.6.32-26 Severity: normal I've downloaded around 600 GB of data round this week and ifconfig(8) was still reporting completly unrealistic figures. /proc/net/dev is consistent with ifconfig figures.
-- Package-specific info: ** Version: Linux version 2.6.32-5-686 (Debian 2.6.32-25) (da...@debian.org) (gcc version 4.3.5 (Debian 4.3.5-4) ) #1 SMP Thu Oct 14 17:15:16 UTC 2010 ** Command line: BOOT_IMAGE=/boot/vmlinuz-2.6.32-5-686 root=UUID=2e624958-cf94-4b06-8c69-69fbed9a22c4 ro quiet ** Not tainted ** Kernel log: [ 1.175672] ACPI: PCI Interrupt Link [LUSB] enabled at IRQ 10 [ 1.175687] ohci_hcd 0000:00:0f.2: PCI INT A -> Link[LUSB] -> GSI 10 (level, low) -> IRQ 10 [ 1.175714] ohci_hcd 0000:00:0f.2: OHCI Host Controller [ 1.175749] ohci_hcd 0000:00:0f.2: new USB bus registered, assigned bus number 1 [ 1.175783] ohci_hcd 0000:00:0f.2: irq 10, io mem 0xfe100000 [ 1.230037] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001 [ 1.230043] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.230046] usb usb1: Product: OHCI Host Controller [ 1.230049] usb usb1: Manufacturer: Linux 2.6.32-5-686 ohci_hcd [ 1.230052] usb usb1: SerialNumber: 0000:00:0f.2 [ 1.230251] usb usb1: configuration #1 chosen from 1 choice [ 1.230337] hub 1-0:1.0: USB hub found [ 1.230353] hub 1-0:1.0: 4 ports detected [ 1.230433] pata_sil680 0000:00:05.0: version 0.4.9 [ 1.230459] pata_sil680 0000:00:05.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 1.230481] sil680: 133MHz clock. [ 1.232723] scsi0 : pata_sil680 [ 1.233639] scsi1 : pata_sil680 [ 1.233720] ata1: PATA max UDMA/133 cmd 0xece8 ctl 0xecf4 bmdma 0xecb0 irq 23 [ 1.233726] ata2: PATA max UDMA/133 cmd 0xecd0 ctl 0xecdc bmdma 0xecb8 irq 23 [ 1.235137] scsi2 : pata_serverworks [ 1.236936] scsi3 : pata_serverworks [ 1.237020] ata3: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x8b0 irq 14 [ 1.237024] ata4: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x8b8 irq 15 [ 1.237233] sata_sil 0000:00:03.0: version 2.4 [ 1.237294] sata_sil 0000:00:03.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 1.237760] scsi4 : sata_sil [ 1.237939] scsi5 : sata_sil [ 1.237989] ata5: SATA max UDMA/100 mmio m...@0xfe102400 tf 0xfe102480 irq 17 [ 1.237994] ata6: SATA max UDMA/100 mmio m...@0xfe102400 tf 0xfe1024c0 irq 17 [ 1.408301] ata3.00: ATAPI: TEAC CD-ROM CD-224E, K.9A, max UDMA/33 [ 1.424312] ata3.00: configured for UDMA/33 [ 1.556032] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 310) [ 1.569705] scsi 2:0:0:0: CD-ROM TEAC CD-224E K.9A PQ: 0 ANSI: 5 [ 1.574782] ata5.00: ATA-8: WDC WD2001FASS-00W2B0, 01.00101, max UDMA/133 [ 1.574788] ata5.00: 3907029168 sectors, multi 16: LBA48 NCQ (depth 0/32) [ 1.581163] ata5.00: configured for UDMA/100 [ 1.735440] scsi 4:0:0:0: Direct-Access ATA WDC WD2001FASS-0 01.0 PQ: 0 ANSI: 5 [ 2.052023] ata6: SATA link down (SStatus 0 SControl 310) [ 2.075438] sd 4:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB) [ 2.075505] sd 4:0:0:0: [sda] Write Protect is off [ 2.075509] sd 4:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 2.075537] sd 4:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 2.075714] sda:sr0: scsi3-mmc drive: 24x/24x cd/rw xa/form2 cdda tray [ 2.081298] Uniform CD-ROM driver Revision: 3.20 [ 2.081804] sr 2:0:0:0: Attached scsi CD-ROM sr0 [ 2.104691] sda1 sda2 sda3 [ 2.105593] sd 4:0:0:0: [sda] Attached SCSI disk [ 2.123413] sr 2:0:0:0: Attached scsi generic sg0 type 5 [ 2.124272] sd 4:0:0:0: Attached scsi generic sg1 type 0 [ 2.307398] PM: Starting manual resume from disk [ 2.307405] PM: Resume from partition 8:3 [ 2.307407] PM: Checking hibernation image. [ 2.307631] PM: Error -22 checking image file [ 2.307634] PM: Resume from disk failed. [ 2.350903] EXT3-fs: INFO: recovery required on readonly filesystem. [ 2.350909] EXT3-fs: write access will be enabled during recovery. [ 8.616736] kjournald starting. Commit interval 5 seconds [ 8.616765] EXT3-fs: sda2: orphan cleanup on readonly fs [ 8.632820] ext3_orphan_cleanup: deleting unreferenced inode 108470387 [ 8.640802] EXT3-fs: sda2: 1 orphan inode deleted [ 8.640805] EXT3-fs: recovery complete. [ 8.658610] EXT3-fs: mounted filesystem with ordered data mode. [ 9.765861] udev: starting version 160 [ 10.107819] input: PC Speaker as /devices/platform/pcspkr/input/input1 [ 10.201499] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2 [ 10.201510] ACPI: Power Button [PWRF] [ 10.203251] processor LNXCPU:00: registered as cooling_device0 [ 10.446095] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2) [ 10.601516] piix4_smbus 0000:00:0f.0: Host SMBus controller not enabled! [ 10.735491] Error: Driver 'pcspkr' is already registered, aborting... [ 11.097524] input: PS/2 Logitech Mouse as /devices/platform/i8042/serio1/input/input3 [ 11.200806] Adding 1509656k swap on /dev/sda3. Priority:-1 extents:1 across:1509656k [ 11.339225] EXT3 FS on sda2, internal journal [ 11.463953] loop: module loaded [ 12.548482] r8169: eth0: link up [ 23.528025] eth0: no IPv6 routers present [ 1752.231699] i2c /dev entries driver [ 1992.283745] Uhhuh. NMI received for unknown reason 31 on CPU 0. [ 1992.283776] Do you have a strange power saving mode enabled? [ 1992.283800] Dazed and confused, but trying to continue [ 2316.697564] process `sysctl' is using deprecated sysctl (syscall) net.ipv6.neigh.default.retrans_time; Use net.ipv6.neigh.default.retrans_time_ms instead. [64273.679071] udev[6496]: starting version 163 [64297.495193] SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled [64297.497303] SGI XFS Quota Management subsystem [64297.506446] JFS: nTxBlock = 4020, nTxLock = 32161 [64297.535077] NTFS driver 2.1.29 [Flags: R/W MODULE]. [64297.557360] QNX4 filesystem 0.2.3 registered. [64297.587669] Btrfs loaded [79877.278405] RPC: Registered udp transport module. [79877.278410] RPC: Registered tcp transport module. [79877.278413] RPC: Registered tcp NFSv4.1 backchannel transport module. [79877.363299] Installing knfsd (copyright (C) 1996 o...@monad.swb.de). [79877.449382] svc: failed to register lockdv1 RPC service (errno 97). [79877.450712] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory [79877.450950] NFSD: starting 90-second grace period [80002.904365] nfsd: last server has exited, flushing export cache [80004.245501] svc: failed to register lockdv1 RPC service (errno 97). [80004.246819] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory [80004.247034] NFSD: starting 90-second grace period ** Model information not available ** Loaded modules: Module Size Used by nfsd 192415 11 lockd 49301 1 nfsd nfs_acl 1695 1 nfsd auth_rpcgss 25200 1 nfsd sunrpc 134116 10 nfsd,lockd,nfs_acl,auth_rpcgss exportfs 2586 1 nfsd crc32c 2172 0 ext4 257163 0 jbd2 55931 1 ext4 crc16 1027 1 ext4 ext2 46157 0 i2c_dev 3505 0 loop 9729 0 snd_pcm 47226 0 snd_timer 12258 1 snd_pcm psmouse 44621 0 i2c_piix4 7076 0 snd 34339 2 snd_pcm,snd_timer dcdbas 3860 0 i2c_core 12660 2 i2c_dev,i2c_piix4 soundcore 3450 1 snd evdev 5609 2 snd_page_alloc 4977 1 snd_pcm serio_raw 2916 0 button 3598 0 processor 26603 0 pcspkr 1207 0 ext3 93832 1 jbd 31965 1 ext3 mbcache 3762 3 ext4,ext2,ext3 sg 15936 0 sr_mod 10770 0 sd_mod 25801 3 crc_t10dif 1012 1 sd_mod cdrom 26487 1 sr_mod ata_generic 2019 0 sata_sil 5620 2 pata_serverworks 3933 0 pata_sil680 3281 0 ohci_hcd 16776 0 ehci_hcd 27615 0 libata 115517 4 ata_generic,sata_sil,pata_serverworks,pata_sil680 thermal 9206 0 usbcore 98185 3 ohci_hcd,ehci_hcd floppy 40923 0 r8169 24716 0 mii 2714 1 r8169 nls_base 4541 1 usbcore thermal_sys 9378 2 processor,thermal scsi_mod 101169 4 sg,sr_mod,sd_mod,libata ** PCI devices: 00:00.0 Host bridge [0600]: Broadcom GCNB-LE Host Bridge [1166:0017] (rev 32) Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00:00.1 Host bridge [0600]: Broadcom GCNB-LE Host Bridge [1166:0017] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00:03.0 Mass storage controller [0180]: Silicon Image, Inc. SiI 3512 [SATALink/SATARaid] Serial ATA Controller [1095:3512] (rev 01) Subsystem: Silicon Image, Inc. SiI 3512 SATALink Controller [1095:3512] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 17 Region 0: I/O ports at ecf8 [size=8] Region 1: I/O ports at ecf0 [size=4] Region 2: I/O ports at ece0 [size=8] Region 3: I/O ports at ecd8 [size=4] Region 4: I/O ports at ecc0 [size=16] Region 5: Memory at fe102400 (32-bit, non-prefetchable) [size=512] Expansion ROM at fe000000 [disabled] [size=512K] Capabilities: [60] Power Management version 2 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=2 PME- Kernel driver in use: sata_sil 00:04.0 VGA compatible controller [0300]: ATI Technologies Inc Rage XL [1002:4752] (rev 27) (prog-if 00 [VGA controller]) Subsystem: Dell Device [1028:0141] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop+ ParErr- Stepping+ SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 (2000ns min), Cache Line Size: 64 bytes Region 0: Memory at fd000000 (32-bit, non-prefetchable) [size=16M] Region 1: I/O ports at e800 [size=256] Region 2: Memory at fe101000 (32-bit, non-prefetchable) [size=4K] [virtual] Expansion ROM at 20080000 [disabled] [size=128K] Capabilities: [5c] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- 00:05.0 IDE interface [0101]: Silicon Image, Inc. PCI0680 Ultra ATA-133 Host Controller [1095:0680] (rev 02) (prog-if 85 [Master SecO PriO]) Subsystem: Dell Device [1028:0141] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32, Cache Line Size: 4 bytes Interrupt: pin A routed to IRQ 23 Region 0: I/O ports at ece8 [size=8] Region 1: I/O ports at ecf4 [size=4] Region 2: I/O ports at ecd0 [size=8] Region 3: I/O ports at ecdc [size=4] Region 4: I/O ports at ecb0 [size=16] Region 5: Memory at fe102000 (32-bit, non-prefetchable) [size=256] Expansion ROM at 20000000 [disabled] [size=512K] Capabilities: [60] Power Management version 2 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=2 PME- Kernel driver in use: pata_sil680 00:0f.0 Host bridge [0600]: Broadcom CSB6 South Bridge [1166:0203] (rev a0) Subsystem: Broadcom Device [1166:0201] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 32 00:0f.1 IDE interface [0101]: Broadcom CSB6 RAID/IDE Controller [1166:0213] (rev a0) (prog-if 8a [Master SecP PriP]) Subsystem: Dell Device [1028:0141] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 32 bytes Region 0: I/O ports at 01f0 [size=8] Region 1: I/O ports at 03f4 [size=1] Region 2: I/O ports at 0170 [size=8] Region 3: I/O ports at 0374 [size=1] Region 4: I/O ports at 08b0 [size=16] Kernel driver in use: pata_serverworks 00:0f.2 USB Controller [0c03]: Broadcom CSB6 OHCI USB Controller [1166:0221] (rev 05) (prog-if 10 [OHCI]) Subsystem: Broadcom Device [1166:0220] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 (20000ns max) Interrupt: pin A routed to IRQ 10 Region 0: Memory at fe100000 (32-bit, non-prefetchable) [size=4K] Kernel driver in use: ohci_hcd 00:0f.3 ISA bridge [0601]: Broadcom GCLE-2 Host Bridge [1166:0227] Subsystem: Broadcom Device [1166:0230] Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 00:10.0 Host bridge [0600]: Broadcom CIOB-E I/O Bridge with Gigabit Ethernet [1166:0110] (rev 12) Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR+ INTx- Capabilities: [60] PCI-X non-bridge device Command: DPERE- ERO- RBC=512 OST=8 Status: Dev=00:00.0 64bit+ 133MHz+ SCD- USC- DC=bridge DMMRBC=512 DMOST=8 DMCRS=8 RSCEM- 266MHz- 533MHz- 00:10.2 Host bridge [0600]: Broadcom CIOB-E I/O Bridge with Gigabit Ethernet [1166:0110] (rev 12) Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Capabilities: [60] PCI-X non-bridge device Command: DPERE- ERO- RBC=512 OST=8 Status: Dev=00:00.0 64bit+ 133MHz+ SCD- USC- DC=bridge DMMRBC=512 DMOST=8 DMCRS=8 RSCEM- 266MHz- 533MHz- 01:03.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL-8169 Gigabit Ethernet [10ec:8169] (rev 10) Subsystem: Realtek Semiconductor Co., Ltd. RTL-8169 Gigabit Ethernet [10ec:8169] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 (8000ns min, 16000ns max), Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 19 Region 0: I/O ports at dc00 [size=256] Region 1: Memory at fcf00000 (32-bit, non-prefetchable) [size=256] Expansion ROM at fce00000 [disabled] [size=128K] Capabilities: [dc] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: r8169 ** USB devices: Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub -- System Information: Debian Release: squeeze/sid APT prefers testing APT policy: (500, 'testing') Architecture: i386 (i686) Kernel: Linux 2.6.32-5-686 (SMP w/1 CPU core) Locale: LANG=fr_FR.UTF-8, LC_CTYPE=fr_FR.UTF-8 (charmap=UTF-8) Shell: /bin/sh linked to /bin/dash Versions of packages linux-image-2.6.32-5-686 depends on: ii debconf [debconf-2.0] 1.5.36 Debian configuration management sy ii initramfs-tools [linux-initra 0.98.5 tools for generating an initramfs ii linux-base 2.6.32-26 Linux image base package ii module-init-tools 3.12-1 tools for managing Linux kernel mo Versions of packages linux-image-2.6.32-5-686 recommends: ii firmware-linux-free 2.6.32-26 Binary firmware for various driver ii libc6-i686 2.11.2-6+squeeze1 Embedded GNU C Library: Shared lib Versions of packages linux-image-2.6.32-5-686 suggests: pn grub | lilo <none> (no description available) pn linux-doc-2.6.32 <none> (no description available) Versions of packages linux-image-2.6.32-5-686 is related to: pn firmware-bnx2 <none> (no description available) pn firmware-bnx2x <none> (no description available) pn firmware-ipw2x00 <none> (no description available) pn firmware-ivtv <none> (no description available) pn firmware-iwlwifi <none> (no description available) ii firmware-linux 0.27 Binary firmware for various driver ii firmware-linux-nonfree 0.27 Binary firmware for various driver pn firmware-qlogic <none> (no description available) pn firmware-ralink <none> (no description available) pn xen-hypervisor <none> (no description available) -- debconf information: linux-image-2.6.32-5-686/prerm/removing-running-kernel-2.6.32-5-686: true linux-image-2.6.32-5-686/postinst/depmod-error-initrd-2.6.32-5-686: false linux-image-2.6.32-5-686/postinst/ignoring-do-bootloader-2.6.32-5-686: linux-image-2.6.32-5-686/postinst/missing-firmware-2.6.32-5-686: -- To UNSUBSCRIBE, email to debian-kernel-requ...@lists.debian.org with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org Archive: http://lists.debian.org/20101028230843.11583.29799.report...@spou.parinux.org