Package: linux-2.6 Version: 3.1.1-1 Severity: critical Justification: breaks the whole system
Dear Maintainer, First of all, thanks for looking into this.. I've installed debian-stable with 2.6.32 kernel. After that, I made the upgrade to wheezy. From that moment on, the system no longer boots: http://tinypic.com/r/2u9222q/5 "BUG: soft lockup - CPU#0 stuck for 23s! [swapper:1]" This messages keeps repeating. When I boot the 2.6.32 kernel, the system works. Hardware is an old Asus A1300 laptop with SiS 630 chipset and Pentium III 1Ghz CPU. Disabling APIC (apic=off) had no effect, having cpufreqd installed or not also makes no difference. I had found these suggestions on the net for similar but different problems. -- Package-specific info: ** Kernel log: boot messages should be attached ** Model information not available ** Network interface configuration: # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface allow-hotplug eth0 iface eth0 inet dhcp ** PCI devices: 00:00.0 Host bridge [0600]: Silicon Integrated Systems [SiS] 630 Host [1039:0630] (rev 31) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 32 Region 0: Memory at d4000000 (32-bit, non-prefetchable) [size=64M] Capabilities: <access denied> Kernel driver in use: agpgart-sis 00:00.1 IDE interface [0101]: Silicon Integrated Systems [SiS] 5513 IDE Controller [1039:5513] (rev d0) (prog-if 80 [Master]) Subsystem: Silicon Integrated Systems [SiS] SiS5513 EIDE Controller (A,B step) [1039:5513] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 128 Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8] Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1] Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8] Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1] Region 4: I/O ports at d800 [size=16] Kernel driver in use: pata_sis 00:01.0 ISA bridge [0601]: Silicon Integrated Systems [SiS] SiS85C503/5513 (LPC Bridge) [1039:0018] Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 00:01.1 Ethernet controller [0200]: Silicon Integrated Systems [SiS] SiS900 PCI Fast Ethernet [1039:0900] (rev 82) Subsystem: ASUSTeK Computer Inc. Device [1043:1455] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 (13000ns min, 2750ns max) Interrupt: pin C routed to IRQ 5 Region 0: I/O ports at d400 [size=256] Region 1: Memory at d3800000 (32-bit, non-prefetchable) [size=4K] [virtual] Expansion ROM at 28000000 [disabled] [size=128K] Capabilities: <access denied> Kernel driver in use: sis900 00:01.2 USB controller [0c03]: Silicon Integrated Systems [SiS] USB 1.1 Controller [1039:7001] (rev 07) (prog-if 10 [OHCI]) Subsystem: Silicon Integrated Systems [SiS] USB 1.1 Controller [1039:7001] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 (20000ns max), Cache Line Size: 32 bytes Interrupt: pin D routed to IRQ 5 Region 0: Memory at d3000000 (32-bit, non-prefetchable) [size=4K] Kernel driver in use: ohci_hcd 00:01.3 USB controller [0c03]: Silicon Integrated Systems [SiS] USB 1.1 Controller [1039:7001] (rev 07) (prog-if 10 [OHCI]) Subsystem: Silicon Integrated Systems [SiS] Onboard USB Controller [1039:7000] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 (20000ns max), Cache Line Size: 32 bytes Interrupt: pin D routed to IRQ 5 Region 0: Memory at d2800000 (32-bit, non-prefetchable) [size=4K] Kernel driver in use: ohci_hcd 00:01.4 Multimedia audio controller [0401]: Silicon Integrated Systems [SiS] SiS PCI Audio Accelerator [1039:7018] (rev 02) Subsystem: Silicon Integrated Systems [SiS] SiS PCI Audio Accelerator [1039:7018] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 (500ns min, 6000ns max) Interrupt: pin B routed to IRQ 5 Region 0: I/O ports at d000 [size=256] Region 1: Memory at d2000000 (32-bit, non-prefetchable) [size=4K] Capabilities: <access denied> Kernel driver in use: Trident4DWaveAudio 00:01.6 Modem [0703]: Silicon Integrated Systems [SiS] AC'97 Modem Controller [1039:7013] (rev a0) (prog-if 00 [Generic]) Subsystem: ASUSTeK Computer Inc. Device [1043:1457] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 (13000ns min, 2750ns max) Interrupt: pin C routed to IRQ 5 Region 0: I/O ports at b800 [size=256] Region 1: I/O ports at b400 [size=128] Capabilities: <access denied> Kernel driver in use: Intel ICH Modem 00:02.0 PCI bridge [0604]: Silicon Integrated Systems [SiS] AGP Port (virtual PCI-to-PCI bridge) [1039:0001] (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 0000a000-0000afff Memory behind bridge: d1800000-d1ffffff Prefetchable memory behind bridge: d8000000-e7efffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- 00:0a.0 CardBus bridge [0607]: Ricoh Co Ltd RL5c476 II [1180:0476] (rev 80) Subsystem: ASUSTeK Computer Inc. Device [1043:1504] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 168 Interrupt: pin A routed to IRQ 11 Region 0: Memory at 28020000 (32-bit, non-prefetchable) [size=4K] Bus: primary=00, secondary=02, subordinate=05, sec-latency=176 Memory window 0: 18000000-1bfff000 (prefetchable) Memory window 1: 1c000000-1ffff000 I/O window 0: 00001000-000010ff I/O window 1: 00001400-000014ff BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+ 16-bit legacy interface ports at 0001 Kernel driver in use: yenta_cardbus 00:0a.1 CardBus bridge [0607]: Ricoh Co Ltd RL5c476 II [1180:0476] (rev 80) Subsystem: ASUSTeK Computer Inc. Device [1043:1504] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 168 Interrupt: pin B routed to IRQ 5 Region 0: Memory at 28021000 (32-bit, non-prefetchable) [size=4K] Bus: primary=00, secondary=06, subordinate=09, sec-latency=176 Memory window 0: 20000000-23fff000 (prefetchable) Memory window 1: 24000000-27fff000 I/O window 0: 00001800-000018ff I/O window 1: 00001c00-00001cff BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+ 16-bit legacy interface ports at 0001 Kernel driver in use: yenta_cardbus 01:00.0 VGA compatible controller [0300]: Silicon Integrated Systems [SiS] 630/730 PCI/AGP VGA Display Adapter [1039:6300] (rev 31) (prog-if 00 [VGA controller]) Subsystem: ASUSTeK Computer Inc. Device [1043:1452] Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- BIST result: 00 Region 0: Memory at d8000000 (32-bit, prefetchable) [size=128M] Region 1: Memory at d1800000 (32-bit, non-prefetchable) [size=128K] Region 2: I/O ports at a800 [size=128] Expansion ROM at <unassigned> [disabled] Capabilities: <access denied> ** USB devices: Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub -- System Information: Debian Release: wheezy/sid APT prefers testing APT policy: (500, 'testing') Architecture: i386 (i686) Kernel: Linux 2.6.32-5-686 (SMP w/1 CPU core) Locale: LANG=en_GB.UTF-8, LC_CTYPE=en_GB.UTF-8 (charmap=UTF-8) Shell: /bin/sh linked to /bin/dash Versions of packages linux-image-3.1.0-1-686-pae depends on: ii debconf [debconf-2.0] 1.5.41 ii initramfs-tools [linux-initramfs-tool] 0.99 ii linux-base 3.4 ii module-init-tools 3.16-1 Versions of packages linux-image-3.1.0-1-686-pae recommends: ii firmware-linux-free 3 ii libc6-i686 2.13-21 Versions of packages linux-image-3.1.0-1-686-pae suggests: pn grub-pc 1.99-14 pn linux-doc-3.1 <none> Versions of packages linux-image-3.1.0-1-686-pae is related to: pn firmware-bnx2 <none> pn firmware-bnx2x <none> pn firmware-ipw2x00 <none> pn firmware-ivtv <none> pn firmware-iwlwifi <none> pn firmware-linux <none> pn firmware-linux-nonfree <none> pn firmware-qlogic <none> pn firmware-ralink <none> pn xen-hypervisor <none> -- debconf information: linux-image-3.1.0-1-686-pae/prerm/removing-running-kernel-3.1.0-1-686-pae: true linux-image-3.1.0-1-686-pae/postinst/missing-firmware-3.1.0-1-686-pae: linux-image-3.1.0-1-686-pae/postinst/ignoring-ramdisk: linux-image-3.1.0-1-686-pae/postinst/depmod-error-initrd-3.1.0-1-686-pae: false -- To UNSUBSCRIBE, email to debian-kernel-requ...@lists.debian.org with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org Archive: http://lists.debian.org/20111227021622.1014.54805.report...@a1300.fritz.box
