Package: linux-2.6 Version: 3.2.1-2~bpo60+1 File: /boot/vmlinuz-3.2.0-0.bpo.1-686-pae Severity: normal
I'll try to do some debugging work later, but just wanted to register
that this bug happens with the backports version of this kernel too.
This is with a Dell Latitude 2100 laptop.
-- Package-specific info:
** Kernel log: boot messages should be attached
** Model information
not available
** Network interface configuration:
auto lo
iface lo inet loopback
allow-hotplug eth0
iface eth0 inet dhcp
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation Mobile 945GME Express Memory
Controller Hub [8086:27ac] (rev 03)
Subsystem: Dell Device [1028:02d6]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: agpgart-intel
00:02.0 VGA compatible controller [0300]: Intel Corporation Mobile 945GME
Express Integrated Graphics Controller [8086:27ae] (rev 03) (prog-if 00 [VGA
controller])
Subsystem: Dell Device [1028:02d6]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f6f00000 (32-bit, non-prefetchable) [size=512K]
Region 1: I/O ports at eff8 [size=8]
Region 2: Memory at e0000000 (32-bit, prefetchable) [size=256M]
Region 3: Memory at f6ec0000 (32-bit, non-prefetchable) [size=256K]
Expansion ROM at <unassigned> [disabled]
Capabilities: <access denied>
Kernel driver in use: i915
00:02.1 Display controller [0380]: Intel Corporation Mobile 945GM/GMS/GME,
943/940GML Express Integrated Graphics Controller [8086:27a6] (rev 03)
Subsystem: Dell Device [1028:02d6]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at f6f80000 (32-bit, non-prefetchable) [size=512K]
Capabilities: <access denied>
00:1b.0 Audio device [0403]: Intel Corporation N10/ICH 7 Family High Definition
Audio Controller [8086:27d8] (rev 01)
Subsystem: Dell Device [1028:02d6]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 45
Region 0: Memory at f6ebc000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
00:1c.0 PCI bridge [0604]: Intel Corporation N10/ICH 7 Family PCI Express Port
1 [8086:27d0] (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=0b, subordinate=0b, sec-latency=0
I/O behind bridge: 00004000-00004fff
Memory behind bridge: 80400000-805fffff
Prefetchable memory behind bridge: 0000000080600000-00000000807fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.1 PCI bridge [0604]: Intel Corporation N10/ICH 7 Family PCI Express Port
2 [8086:27d2] (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=0c, subordinate=0c, sec-latency=0
I/O behind bridge: 00003000-00003fff
Memory behind bridge: f6d00000-f6dfffff
Prefetchable memory behind bridge: 0000000080200000-00000000803fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.3 PCI bridge [0604]: Intel Corporation N10/ICH 7 Family PCI Express Port
4 [8086:27d6] (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=09, subordinate=09, sec-latency=0
I/O behind bridge: 00002000-00002fff
Memory behind bridge: f6c00000-f6cfffff
Prefetchable memory behind bridge: 0000000080000000-00000000801fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1d.0 USB Controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI
Controller #1 [8086:27c8] (rev 01) (prog-if 00 [UHCI])
Subsystem: Dell Device [1028:02d6]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 4: I/O ports at bf80 [size=32]
Kernel driver in use: uhci_hcd
00:1d.1 USB Controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI
Controller #2 [8086:27c9] (rev 01) (prog-if 00 [UHCI])
Subsystem: Dell Device [1028:02d6]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at bf60 [size=32]
Kernel driver in use: uhci_hcd
00:1d.2 USB Controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI
Controller #3 [8086:27ca] (rev 01) (prog-if 00 [UHCI])
Subsystem: Dell Device [1028:02d6]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 22
Region 4: I/O ports at bf40 [size=32]
Kernel driver in use: uhci_hcd
00:1d.3 USB Controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI
Controller #4 [8086:27cb] (rev 01) (prog-if 00 [UHCI])
Subsystem: Dell Device [1028:02d6]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 23
Region 4: I/O ports at bf20 [size=32]
Kernel driver in use: uhci_hcd
00:1d.7 USB Controller [0c03]: Intel Corporation N10/ICH 7 Family USB2 EHCI
Controller [8086:27cc] (rev 01) (prog-if 20 [EHCI])
Subsystem: Dell Device [1028:02d6]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 0: Memory at fed1c000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge
[8086:2448] (rev e1) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=32
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation 82801GBM (ICH7-M) LPC Interface
Bridge [8086:27b9] (rev 01)
Subsystem: Dell Device [1028:02d6]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:1f.2 SATA controller [0106]: Intel Corporation 82801GBM/GHM (ICH7 Family)
SATA AHCI Controller [8086:27c5] (rev 01) (prog-if 01 [AHCI 1.0])
Subsystem: Dell Device [1028:02d6]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 43
Region 0: I/O ports at 6e70 [size=8]
Region 1: I/O ports at 6e78 [size=4]
Region 2: I/O ports at 6e80 [size=8]
Region 3: I/O ports at 6e88 [size=4]
Region 4: I/O ports at 6ea0 [size=32]
Region 5: Memory at fed1c800 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ahci
00:1f.3 SMBus [0c05]: Intel Corporation N10/ICH 7 Family SMBus Controller
[8086:27da] (rev 01)
Subsystem: Dell Device [1028:02d6]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at 10c0 [size=32]
Kernel driver in use: i801_smbus
09:00.0 Ethernet controller [0200]: Broadcom Corporation NetXtreme BCM5764M
Gigabit Ethernet PCIe [14e4:1684] (rev 10)
Subsystem: Dell Device [1028:02d6]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 46
Region 0: Memory at f6cf0000 (64-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
Kernel driver in use: tg3
0c:00.0 Network controller [0280]: Intel Corporation WiFi Link 5100 [8086:4232]
Subsystem: Intel Corporation WiFi Link 5100 AGN [8086:1321]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 44
Region 0: Memory at f6dfe000 (64-bit, non-prefetchable) [size=8K]
Capabilities: <access denied>
Kernel driver in use: iwlagn
** USB devices:
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 002: ID 1cb6:6680
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 003: ID 0c45:6404 Microdia
Bus 001 Device 002: ID 0bda:0158 Realtek Semiconductor Corp. USB 2.0 multicard
reader
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
-- System Information:
Debian Release: 6.0.4
APT prefers stable-updates
APT policy: (500, 'stable-updates'), (500, 'proposed-updates'), (500,
'stable'), (90, 'testing')
Architecture: i386 (i686)
Kernel: Linux 2.6.39-bpo.2-686-pae (SMP w/2 CPU cores)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-3.2.0-0.bpo.1-686-pae depends on:
ii debconf [debconf-2.0] 1.5.36.1 Debian configuration management sy
ii initramfs-tools [linux-init 0.99~bpo60+1 tools for generating an initramfs
ii linux-base 3.4~bpo60+1 Linux image base package
ii module-init-tools 3.12-2+b1 tools for managing Linux kernel mo
Versions of packages linux-image-3.2.0-0.bpo.1-686-pae recommends:
ii firmware-linux-free 2.6.32-41 Binary firmware for various driver
ii libc6-i686 2.11.3-2 Embedded GNU C Library: Shared lib
Versions of packages linux-image-3.2.0-0.bpo.1-686-pae suggests:
ii grub-pc 1.99-14 GRand Unified Bootloader, version
pn linux-doc-3.2 <none> (no description available)
Versions of packages linux-image-3.2.0-0.bpo.1-686-pae is related to:
pn firmware-atheros <none> (no description available)
pn firmware-bnx2 <none> (no description available)
pn firmware-bnx2x <none> (no description available)
pn firmware-brcm80211 <none> (no description available)
pn firmware-intelwimax <none> (no description available)
pn firmware-ipw2x00 <none> (no description available)
pn firmware-ivtv <none> (no description available)
ii firmware-iwlwifi 0.35~bpo60+1 Binary firmware for Intel Wireless
pn firmware-libertas <none> (no description available)
ii firmware-linux 0.35~bpo60+1 Binary firmware for various driver
ii firmware-linux-nonfree 0.35~bpo60+1 Binary firmware for various driver
pn firmware-myricom <none> (no description available)
pn firmware-netxen <none> (no description available)
pn firmware-qlogic <none> (no description available)
pn firmware-ralink <none> (no description available)
pn firmware-realtek <none> (no description available)
pn xen-hypervisor <none> (no description available)
-- debconf information:
linux-image-3.2.0-0.bpo.1-686-pae/postinst/depmod-error-initrd-3.2.0-0.bpo.1-686-pae:
false
linux-image-3.2.0-0.bpo.1-686-pae/postinst/missing-firmware-3.2.0-0.bpo.1-686-pae:
linux-image-3.2.0-0.bpo.1-686-pae/postinst/ignoring-ramdisk:
linux-image-3.2.0-0.bpo.1-686-pae/prerm/removing-running-kernel-3.2.0-0.bpo.1-686-pae:
true
--
Kenyon Ralph
signature.asc
Description: Digital signature
