Package: linux-2.6 Version: 3.2.6-1 Severity: important After the update to kernel version 3.2.0 the system fails to detect the soundcard (snd_hda_intel) and framebuffer (i915) and X.org fails to start.
Comparing with the previous kernel version 3.1.0 I found several missing modules. But even if I load these modules (which works without errors), X.org still doesn't want to start. Any ideas, where to look for the error? I already checked syslog and dmesg and could not find anything special, besides the missing | [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0 which normally appears right after the bluetooth initialization. The X.org logfile is also not very helpful, it just says "(EE) No devices detected" after trying to load the i810 driver. The graphic hardware in question is the onboard device in a Samsung NC10 netbook. (lspci says, it is a "Intel Coprporation Mobile 945GME Express Integrated Graphics Controller (rev 03)") Find below a diff between "lsmod" output on a good (3.1.0) kernel and the bad (3.2.0) kernel. I would be glad to help finding the problem. Thanks in advance, Johannes --- erg.good.mod 2012-03-10 12:13:49.000000000 +0100 +++ erg.bad.mod 2012-03-10 12:13:39.000000000 +0100 @@ -1,87 +1,38 @@ -ac 12552 0 acpi_cpufreq 12807 1 -aes_generic 32970 1 aes_i586 -aes_i586 16608 1 -arc4 12418 2 ata_generic 12439 0 -ath 17114 1 ath5k -ath5k 115246 0 -battery 12957 0 binfmt_misc 12813 1 bnep 17288 2 -btusb 17278 1 -button 12817 1 i915 -cfg80211 113073 3 ath5k,ath,mac80211 cpufreq_conservative 12987 0 cpufreq_powersave 12422 0 cpufreq_stats 12762 0 cpufreq_userspace 12520 0 crc16 12327 1 bluetooth crc_t10dif 12332 1 sd_mod -cryptd 14125 0 -drm 129839 3 i915,drm_kms_helper -drm_kms_helper 22699 1 i915 -ecb 12649 1 ehci_hcd 35509 0 -evdev 17225 28 fan 12594 0 -i2c_algo_bit 12713 1 i915 -i2c_core 19116 6 videodev,i915,drm_kms_helper,drm,i2c_algo_bit,i2c_i801 -i2c_i801 12670 0 -i915 303824 2 -iTCO_vendor_support 12632 1 iTCO_wdt -iTCO_wdt 16945 0 -joydev 17010 0 lp 12797 0 -mac80211 166082 1 ath5k mbcache 12897 1 ext3 -media 13692 2 uvcvideo,videodev Module Size Used by mperf 12421 1 acpi_cpufreq parport 31254 3 parport_pc,ppdev,lp parport_pc 22036 0 -pcspkr 12515 0 -power_supply 13283 2 ac,battery ppdev 12651 0 -psmouse 46143 0 -rng_core 12580 0 -samsung_laptop 12660 0 sd_mod 35425 3 -serio_raw 12738 0 -snd 38551 12 snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device -snd_hda_codec 58526 2 snd_hda_codec_realtek,snd_hda_intel -snd_hda_codec_realtek 196816 1 -snd_hda_intel 21725 0 -snd_hrtimer 12540 1 -snd_hwdep 12943 1 snd_hda_codec -snd_mixer_oss 17668 1 snd_pcm_oss -snd_page_alloc 12867 2 snd_hda_intel,snd_pcm -snd_pcm 53258 3 snd_hda_intel,snd_hda_codec,snd_pcm_oss -snd_pcm_oss 36181 0 -snd_rawmidi 18376 1 snd_seq_midi -snd_seq 39487 3 snd_seq_midi,snd_seq_midi_event -snd_seq_device 13016 3 snd_seq_midi,snd_rawmidi,snd_seq -snd_seq_midi 12744 0 -snd_seq_midi_event 13124 1 snd_seq_midi -snd_timer 22356 3 snd_hrtimer,snd_pcm,snd_seq -soundcore 12921 1 snd thermal 13103 0 uhci_hcd 22337 0 -uvcvideo 56932 0 -video 17412 1 i915 -videodev 61627 1 uvcvideo -- Package-specific info: ** Version: Linux version 3.2.0-1-686-pae (Debian 3.2.6-1) (b...@decadent.org.uk) (gcc version 4.6.2 (Debian 4.6.2-14) ) #1 SMP Fri Feb 17 06:27:21 UTC 2012 ** Command line: BOOT_IMAGE=/boot/vmlinuz-3.2.0-1-686-pae root=UUID=8b6ce2c8-a8f1-44b7-bb24-0edb0d468b28 ro ** Not tainted ** Kernel log: [ 1.562191] usb usb5: Manufacturer: Linux 3.2.0-1-686-pae uhci_hcd [ 1.562280] usb usb5: SerialNumber: 0000:00:1d.3 [ 1.565962] hub 5-0:1.0: USB hub found [ 1.566066] hub 5-0:1.0: 2 ports detected [ 1.617142] SCSI subsystem initialized [ 1.637088] libata version 3.00 loaded. [ 1.638377] ata_piix 0000:00:1f.2: version 2.13 [ 1.638418] ata_piix 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 1.638525] ata_piix 0000:00:1f.2: MAP [ P0 P2 IDE IDE ] [ 1.792169] ata_piix 0000:00:1f.2: setting latency timer to 64 [ 1.793459] scsi0 : ata_piix [ 1.793885] scsi1 : ata_piix [ 1.795639] ata1: SATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0x1810 irq 14 [ 1.795727] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x1818 irq 15 [ 1.796541] ata2: port disabled--ignoring [ 1.936162] usb 1-8: new high-speed USB device number 3 using ehci_hcd [ 1.991585] ata1.00: ATA-8: WDC WD1600BEVT-22ZCT0, 11.01A11, max UDMA/133 [ 1.991691] ata1.00: 312581808 sectors, multi 16: LBA48 NCQ (depth 0/32) [ 2.005562] ata1.00: configured for UDMA/133 [ 2.006031] scsi 0:0:0:0: Direct-Access ATA WDC WD1600BEVT-2 11.0 PQ: 0 ANSI: 5 [ 2.019177] sd 0:0:0:0: [sda] 312581808 512-byte logical blocks: (160 GB/149 GiB) [ 2.019541] sd 0:0:0:0: [sda] Write Protect is off [ 2.019639] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 2.019769] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 2.046825] sda: sda1 sda2 sda3 sda4 [ 2.048323] sd 0:0:0:0: [sda] Attached SCSI disk [ 2.103285] usb 1-8: New USB device found, idVendor=174f, idProduct=5933 [ 2.103390] usb 1-8: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 2.103485] usb 1-8: Product: USB Camera Device [ 2.103570] usb 1-8: Manufacturer: Syntek [ 2.103654] usb 1-8: SerialNumber: STK00001 [ 2.376160] usb 3-2: new full-speed USB device number 2 using uhci_hcd [ 2.550818] usb 3-2: New USB device found, idVendor=0a5c, idProduct=2151 [ 2.550924] usb 3-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 2.551020] usb 3-2: Product: BCM2046 Bluetooth Device [ 2.551115] usb 3-2: Manufacturer: Broadcom Corp [ 2.551191] usb 3-2: SerialNumber: 0C6076E2140D [ 2.712412] device-mapper: uevent: version 1.0.3 [ 2.712977] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-de...@redhat.com [ 2.775531] PM: Starting manual resume from disk [ 2.775634] PM: Hibernation image partition 8:2 present [ 2.775638] PM: Looking for hibernation image. [ 2.776056] PM: Image not found (code -22) [ 2.776061] PM: Hibernation image not present or could not be loaded. [ 2.785031] PM: Marking nosave pages: 000000000009f000 - 0000000000100000 [ 2.785042] PM: Basic memory bitmaps created [ 2.797636] PM: Basic memory bitmaps freed [ 2.880789] kjournald starting. Commit interval 5 seconds [ 2.881094] EXT3-fs (sda3): mounted filesystem with ordered data mode [ 7.164399] Adding 2000088k swap on /dev/sda2. Priority:-1 extents:1 across:2000088k [ 7.501300] EXT3-fs (sda3): using internal journal [ 12.684157] fuse init (API version 7.17) [ 25.008172] Bluetooth: Core ver 2.16 [ 25.008299] NET: Registered protocol family 31 [ 25.008376] Bluetooth: HCI device and connection manager initialized [ 25.008458] Bluetooth: HCI socket layer initialized [ 25.008535] Bluetooth: L2CAP socket layer initialized [ 25.008620] Bluetooth: SCO socket layer initialized [ 25.040838] Bluetooth: RFCOMM TTY layer initialized [ 25.040932] Bluetooth: RFCOMM socket layer initialized [ 25.041011] Bluetooth: RFCOMM ver 1.11 [ 25.336690] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 25.336776] Bluetooth: BNEP filters: protocol multicast [ 33.951411] lp: driver loaded but no devices found [ 33.960756] ppdev: user-space parallel port driver [ 44.443026] inputlircd[1556]: segfault at dfacce44 ip 0804978d sp bfacca10 error 7 in inputlircd[8048000+4000] [ 150.748486] sky2 0000:03:00.0: eth0: enabling interface [ 150.749777] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 152.223037] sky2 0000:03:00.0: eth0: Link is up at 100 Mbps, full duplex, flow control both [ 152.223871] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 162.592080] eth0: no IPv6 routers present [ 673.898695] acpi device:04: registered as cooling_device3 [ 673.899046] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input1 [ 673.899162] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no) [ 673.944347] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input2 [ 673.944524] ACPI: Lid Switch [LID0] [ 673.944755] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input3 [ 673.944865] ACPI: Power Button [PWRB] [ 673.945093] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input4 [ 673.945201] ACPI: Sleep Button [SLPB] [ 673.945429] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input5 [ 673.945534] ACPI: Power Button [PWRF] [ 674.043128] [drm] Initialized drm 1.1.0 20060810 [ 674.199999] i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 674.200145] i915 0000:00:02.0: setting latency timer to 64 [ 674.277675] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010). [ 674.277776] [drm] Driver supports precise vblank timestamp query. [ 674.278097] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem [ 674.610616] [drm] initialized overlay support [ 674.633309] fbcon: inteldrmfb (fb0) is primary device [ 675.023855] Console: switching to colour frame buffer device 128x37 [ 675.041481] fb0: inteldrmfb frame buffer device [ 675.041486] drm: registered panic notifier [ 675.041767] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0 [ 714.938914] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 [ 714.942736] snd_hda_intel 0000:00:1b.0: irq 43 for MSI/MSI-X [ 714.942800] snd_hda_intel 0000:00:1b.0: setting latency timer to 64 [ 715.000701] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input6 [ 715.007799] input: HDA Intel Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input7 [ 715.011621] input: HDA Intel Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8 ** Model information not available ** Loaded modules: snd_hda_codec_realtek snd_hda_intel snd_hda_codec snd_hwdep snd_pcm_oss snd_mixer_oss snd_pcm snd_seq_midi snd_rawmidi snd_seq_midi_event snd_seq snd_timer snd_seq_device snd soundcore snd_page_alloc i915 drm_kms_helper drm i2c_algo_bit button i2c_core video acpi_cpufreq processor mperf cpufreq_conservative cpufreq_userspace cpufreq_powersave cpufreq_stats parport_pc ppdev lp parport bnep rfcomm bluetooth rfkill crc16 binfmt_misc uinput fuse ext3 jbd mbcache dm_mod sd_mod crc_t10dif ata_generic ata_piix libata scsi_mod thermal uhci_hcd fan thermal_sys sky2 ehci_hcd usbcore usb_common ** PCI devices: 00:00.0 Host bridge [0600]: Intel Corporation Mobile 945GME Express Memory Controller Hub [8086:27ac] (rev 03) Subsystem: Samsung Electronics Co Ltd Device [144d:ca00] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 0 Capabilities: <access denied> 00:02.0 VGA compatible controller [0300]: Intel Corporation Mobile 945GME Express Integrated Graphics Controller [8086:27ae] (rev 03) (prog-if 00 [VGA controller]) Subsystem: Samsung Electronics Co Ltd Device [144d:ca00] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 0: Memory at f0000000 (32-bit, non-prefetchable) [size=512K] Region 1: I/O ports at 1800 [size=8] Region 2: Memory at d0000000 (32-bit, prefetchable) [size=256M] Region 3: Memory at f0300000 (32-bit, non-prefetchable) [size=256K] Expansion ROM at <unassigned> [disabled] Capabilities: <access denied> 00:02.1 Display controller [0380]: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller [8086:27a6] (rev 03) Subsystem: Samsung Electronics Co Ltd Device [144d:ca00] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Region 0: Memory at f0080000 (32-bit, non-prefetchable) [size=512K] Capabilities: <access denied> 00:1b.0 Audio device [0403]: Intel Corporation N10/ICH 7 Family High Definition Audio Controller [8086:27d8] (rev 02) Subsystem: Samsung Electronics Co Ltd Device [144d:ca00] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 43 Region 0: Memory at f0340000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> 00:1c.0 PCI bridge [0604]: Intel Corporation N10/ICH 7 Family PCI Express Port 1 [8086:27d0] (rev 02) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 I/O behind bridge: 00003000-00003fff Memory behind bridge: f0100000-f01fffff Prefetchable memory behind bridge: 0000000040200000-00000000403fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> 00:1c.2 PCI bridge [0604]: Intel Corporation N10/ICH 7 Family PCI Express Port 3 [8086:27d4] (rev 02) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=03, subordinate=03, sec-latency=0 I/O behind bridge: 00002000-00002fff Memory behind bridge: f0200000-f02fffff Prefetchable memory behind bridge: 0000000040000000-00000000401fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> 00:1d.0 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 [8086:27c8] (rev 02) (prog-if 00 [UHCI]) Subsystem: Samsung Electronics Co Ltd Device [144d:ca00] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 23 Region 4: I/O ports at 1820 [size=32] 00:1d.1 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 [8086:27c9] (rev 02) (prog-if 00 [UHCI]) Subsystem: Samsung Electronics Co Ltd Device [144d:ca00] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 19 Region 4: I/O ports at 1840 [size=32] 00:1d.2 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 [8086:27ca] (rev 02) (prog-if 00 [UHCI]) Subsystem: Samsung Electronics Co Ltd Device [144d:ca00] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin C routed to IRQ 18 Region 4: I/O ports at 1860 [size=32] 00:1d.3 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 [8086:27cb] (rev 02) (prog-if 00 [UHCI]) Subsystem: Samsung Electronics Co Ltd Device [144d:ca00] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin D routed to IRQ 16 Region 4: I/O ports at 1880 [size=32] 00:1d.7 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller [8086:27cc] (rev 02) (prog-if 20 [EHCI]) Subsystem: Samsung Electronics Co Ltd Device [144d:ca00] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 23 Region 0: Memory at f0544000 (32-bit, non-prefetchable) [size=1K] Capabilities: <access denied> 00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev e2) (prog-if 01 [Subtractive decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Bus: primary=00, secondary=04, subordinate=04, sec-latency=0 Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> 00:1f.0 ISA bridge [0601]: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge [8086:27b9] (rev 02) Subsystem: Samsung Electronics Co Ltd Device [144d:ca00] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Capabilities: <access denied> 00:1f.2 IDE interface [0101]: Intel Corporation 82801GBM/GHM (ICH7-M Family) SATA Controller [IDE mode] [8086:27c4] (rev 02) (prog-if 80 [Master]) Subsystem: Samsung Electronics Co Ltd Device [144d:ca00] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx+ Latency: 0 Interrupt: pin B routed to IRQ 19 Region 0: I/O ports at 01f0 [size=8] Region 1: I/O ports at 03f4 Region 2: I/O ports at 0170 [size=8] Region 3: I/O ports at 0374 Region 4: I/O ports at 1810 [size=16] Capabilities: <access denied> 00:1f.3 SMBus [0c05]: Intel Corporation N10/ICH 7 Family SMBus Controller [8086:27da] (rev 02) Subsystem: Samsung Electronics Co Ltd Device [144d:ca00] Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin B routed to IRQ 5 Region 4: I/O ports at 18a0 [size=32] 02:00.0 Ethernet controller [0200]: Atheros Communications Inc. AR242x / AR542x Wireless Network Adapter (PCI-Express) [168c:001c] (rev 01) Subsystem: Askey Computer Corp. Device [144f:7131] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 11 Region 0: Memory at f0100000 (64-bit, non-prefetchable) [size=64K] Capabilities: <access denied> 03:00.0 Ethernet controller [0200]: Marvell Technology Group Ltd. 88E8040 PCI-E Fast Ethernet Controller [11ab:4354] (rev 13) Subsystem: Samsung Electronics Co Ltd Device [144d:ca00] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 42 Region 0: Memory at f0200000 (64-bit, non-prefetchable) [size=16K] Region 2: I/O ports at 2000 [size=256] Capabilities: <access denied> ** USB devices: Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 002: ID 0a5c:2151 Broadcom Corp. Bluetooth Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 003: ID 174f:5933 Syntek Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub -- System Information: Debian Release: wheezy/sid APT prefers testing APT policy: (500, 'testing'), (500, 'stable') Architecture: i386 (i686) Kernel: Linux 3.2.0-1-686-pae (SMP w/2 CPU cores) Locale: LANG=de_DE.UTF-8, LC_CTYPE=de_DE.UTF-8 (charmap=UTF-8) Shell: /bin/sh linked to /bin/dash Versions of packages linux-image-3.2.0-1-686-pae depends on: ii debconf [debconf-2.0] 1.5.41 ii initramfs-tools [linux-initramfs-tool] 0.100 ii linux-base 3.4 ii module-init-tools 3.16-1 Versions of packages linux-image-3.2.0-1-686-pae recommends: ii firmware-linux-free 3 ii libc6-i686 2.13-27 Versions of packages linux-image-3.2.0-1-686-pae suggests: pn grub-pc 1.99-14 pn linux-doc-3.2 <none> Versions of packages linux-image-3.2.0-1-686-pae is related to: pn firmware-atheros <none> pn firmware-bnx2 <none> pn firmware-bnx2x <none> pn firmware-brcm80211 <none> pn firmware-intelwimax <none> pn firmware-ipw2x00 <none> pn firmware-ivtv <none> pn firmware-iwlwifi <none> pn firmware-libertas <none> pn firmware-linux 0.35 pn firmware-linux-nonfree 0.35 pn firmware-myricom <none> pn firmware-netxen <none> pn firmware-qlogic <none> pn firmware-ralink <none> pn firmware-realtek <none> pn xen-hypervisor <none> -- debconf information: linux-image-3.2.0-1-686-pae/postinst/missing-firmware-3.2.0-1-686-pae: linux-image-3.2.0-1-686-pae/prerm/removing-running-kernel-3.2.0-1-686-pae: true linux-image-3.2.0-1-686-pae/postinst/ignoring-ramdisk: linux-image-3.2.0-1-686-pae/postinst/depmod-error-initrd-3.2.0-1-686-pae: false -- To UNSUBSCRIBE, email to debian-kernel-requ...@lists.debian.org with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org Archive: http://lists.debian.org/20120310115041.ga26...@graograman.kolb.regensburg