Package: src:linux Version: 3.2.41-2 Severity: grave Justification: renders package unusable
---------- I have upgraded today from Squeeze to Debian-7.0. However, while booting in the last 3 occasions, the machine hanged twice with kernel Panic. In both the occasions, the kernel waited unusually long to load the initrd, and then complained about it and then asked to touch any key to continue. Once I touched something, it panicked. What surprises me is that if it is a initrd problem, why did it boot in 2 other occasions ? Moreover, I have been using 'vmlinuz-3.2.0-0.bpo.2-amd64' taken from backport while using Squeeze, and the machine never hanged in the last 6 months. The messages were captured with a camera and I am writing down most of it as was visible in the last screen. ----------- No filesystem could mount root. tried: Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0, 0) Pid: 1, comm: swapper/0 Not tainted 3.2.0-4-amd64 #1 Debian 3.2.41-2 Call Trace: ....................... ? panic+0x95/0x1a2 ....................... ....................... ....................... ? gs_change+0x13/0x13 -- Package-specific info: ** Version: Linux version 3.2.0-4-amd64 (debian-kernel@lists.debian.org) (gcc version 4.6.3 (Debian 4.6.3-15) ) #1 SMP Debian 3.2.41-2 ** Command line: BOOT_IMAGE=/boot/vmlinuz-3.2.0-4-amd64 root=UUID=56da2c0c-5a03-4b11-b6f3-6e15ebcb7782 ro verbose resume=/dev/sda4 ** Not tainted ** Kernel log: [ 1.885842] usb 2-1.5: Manufacturer: Logitech [ 2.200896] ata5: SATA link down (SStatus 0 SControl 300) [ 2.520295] ata6: SATA link down (SStatus 0 SControl 300) [ 2.523950] sd 0:0:0:0: [sda] 78242976 512-byte logical blocks: (40.0 GB/37.3 GiB) [ 2.524064] sd 0:0:0:0: [sda] Write Protect is off [ 2.524128] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 2.524146] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 2.524629] input: Logitech USB Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.5/2-1.5:1.0/input/input1 [ 2.524836] generic-usb 0003:046D:C06A.0001: input,hidraw0: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-0000:00:1d.0-1.5/input0 [ 2.524936] usbcore: registered new interface driver usbhid [ 2.525001] usbhid: USB HID core driver [ 2.530135] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray [ 2.530227] cdrom: Uniform CD-ROM driver Revision: 3.20 [ 2.530429] sr 1:0:0:0: Attached scsi CD-ROM sr0 [ 2.564825] sda: sda1 sda2 sda3 sda4 [ 2.565453] sd 0:0:0:0: [sda] Attached SCSI disk [ 2.567646] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 2.567772] sr 1:0:0:0: Attached scsi generic sg1 type 5 [ 3.364096] Btrfs loaded [ 3.488917] PM: Starting manual resume from disk [ 3.488982] PM: Hibernation image partition 8:4 present [ 3.488984] PM: Looking for hibernation image. [ 3.504857] PM: Image not found (code -22) [ 3.504859] PM: Hibernation image not present or could not be loaded. [ 3.544870] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null) [ 5.666963] udevd[358]: starting version 175 [ 6.078839] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input2 [ 6.078927] ACPI: Power Button [PWRB] [ 6.079040] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3 [ 6.079119] ACPI: Power Button [PWRF] [ 6.266960] ACPI: Requesting acpi_cpufreq [ 6.376480] input: PC Speaker as /devices/platform/pcspkr/input/input4 [ 6.535696] parport_pc 00:08: reported by Plug and Play ACPI [ 6.535812] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE] [ 6.699277] iTCO_vendor_support: vendor-support=0 [ 6.719670] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.07 [ 6.719797] iTCO_wdt: unable to reset NO_REBOOT flag, device disabled by hardware/BIOS [ 6.873779] [drm] Initialized drm 1.1.0 20060810 [ 6.960195] i915 0000:00:02.0: setting latency timer to 64 [ 6.979763] mtrr: type mismatch for e0000000,10000000 old: write-back new: write-combining [ 6.979845] [drm] MTRR allocation failed. Graphics performance may suffer. [ 6.980052] i915 0000:00:02.0: irq 41 for MSI/MSI-X [ 6.980057] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010). [ 6.980122] [drm] Driver supports precise vblank timestamp query. [ 6.980215] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem [ 7.029261] [drm] Enabling RC6 states: RC6 on, RC6p off, RC6pp off [ 7.353414] fbcon: inteldrmfb (fb0) is primary device [ 7.475416] udevd[506]: renamed network interface eth0 to eth5 [ 7.646037] Console: switching to colour frame buffer device 240x67 [ 7.653630] fb0: inteldrmfb frame buffer device [ 7.653657] drm: registered panic notifier [ 7.653718] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0 [ 7.653859] snd_hda_intel 0000:00:1b.0: irq 42 for MSI/MSI-X [ 7.653882] snd_hda_intel 0000:00:1b.0: setting latency timer to 64 [ 8.265600] HDMI status: Codec=3 Pin=7 Presence_Detect=1 ELD_Valid=1 [ 8.265606] HDMI hot plug event: Codec=3 Pin=7 Presence_Detect=1 ELD_Valid=1 [ 8.265700] HDMI status: Codec=3 Pin=7 Presence_Detect=1 ELD_Valid=1 [ 8.272566] HDMI: detected monitor 2353 at connection type HDMI [ 8.272603] HDMI: available speakers: FL/FR [ 8.272633] HDMI: supports coding type LPCM: channels = 2, rates = 32000 44100 48000, bits = 16 [ 8.272779] HDMI: detected monitor 2353 at connection type HDMI [ 8.272815] HDMI: available speakers: FL/FR [ 8.272842] HDMI: supports coding type LPCM: channels = 2, rates = 32000 44100 48000, bits = 16 [ 8.272930] input: HDA Intel PCH HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1b.0/sound/card0/input5 [ 8.272995] HDMI hot plug event: Codec=3 Pin=7 Presence_Detect=1 ELD_Valid=1 [ 8.273068] HDMI status: Codec=3 Pin=7 Presence_Detect=1 ELD_Valid=1 [ 8.278793] HDMI: detected monitor 2353 at connection type HDMI [ 8.278834] HDMI: available speakers: FL/FR [ 8.278862] HDMI: supports coding type LPCM: channels = 2, rates = 32000 44100 48000, bits = 16 [ 9.315943] Adding 1773152k swap on /dev/sda4. Priority:-1 extents:1 across:1773152k [ 9.333623] EXT4-fs (sda2): re-mounted. Opts: (null) [ 9.595027] EXT4-fs (sda2): re-mounted. Opts: barrier=1,errors=remount-ro [ 10.178816] device-mapper: uevent: version 1.0.3 [ 10.178914] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-de...@redhat.com [ 10.387760] it87: Found IT8728F chip at 0x290, revision 1 [ 10.390277] it87: Beeping is supported [ 11.095373] EXT4-fs (sda3): mounted filesystem with ordered data mode. Opts: barrier=1 [ 12.383426] RPC: Registered named UNIX socket transport module. [ 12.385550] RPC: Registered udp transport module. [ 12.387671] RPC: Registered tcp transport module. [ 12.389760] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 12.448656] FS-Cache: Loaded [ 12.514715] FS-Cache: Netfs 'nfs' registered for caching [ 12.541032] Installing knfsd (copyright (C) 1996 o...@monad.swb.de). [ 12.871999] fuse init (API version 7.17) [ 13.619923] ttyS0: LSR safety check engaged! [ 13.622265] ttyS0: LSR safety check engaged! [ 14.396465] NET: Registered protocol family 15 [ 14.417814] alg: No test for cipher_null (cipher_null-generic) [ 14.419765] alg: No test for ecb(cipher_null) (ecb-cipher_null) [ 14.422838] alg: No test for digest_null (digest_null-generic) [ 14.424767] alg: No test for compress_null (compress_null-generic) [ 14.479099] sha1_ssse3: Using SSSE3 optimized SHA-1 implementation [ 16.209900] input: ACPI Virtual Keyboard Device as /devices/virtual/input/input6 [ 85.355762] atl1c 0000:04:00.0: irq 43 for MSI/MSI-X [ 85.355883] atl1c 0000:04:00.0: atl1c: eth5 NIC Link is Up<100 Mbps Full Duplex> [ 95.578966] eth5: no IPv6 routers present [ 194.783406] atl1c 0000:04:00.0: irq 43 for MSI/MSI-X [ 194.783490] atl1c 0000:04:00.0: atl1c: eth0 NIC Link is Up<100 Mbps Full Duplex> [ 204.948648] eth0: no IPv6 routers present ** Model information sys_vendor: Gigabyte Technology Co., Ltd. product_name: H61M-D2H product_version: chassis_vendor: Gigabyte Technology Co., Ltd. chassis_version: bios_vendor: Award Software International, Inc. bios_version: F2 board_vendor: Gigabyte Technology Co., Ltd. board_name: H61M-D2H board_version: ** Loaded modules: acpi_cpufreq cpufreq_conservative cpufreq_userspace cpufreq_stats cpufreq_powersave uinput deflate ctr twofish_generic twofish_x86_64_3way twofish_x86_64 twofish_common camellia serpent blowfish_generic blowfish_x86_64 blowfish_common cast5 des_generic cbc aes_x86_64 aes_generic xcbc rmd160 sha512_generic sha256_generic sha1_ssse3 sha1_generic hmac crypto_null af_key fuse nfsd nfs nfs_acl auth_rpcgss fscache lockd sunrpc it87 hwmon_vid dm_crypt dm_mod snd_hda_codec_hdmi snd_hda_codec_realtek snd_hda_intel snd_hda_codec snd_hwdep snd_pcm_oss snd_mixer_oss snd_pcm snd_page_alloc snd_seq_midi i915 video drm_kms_helper snd_seq_midi_event drm snd_rawmidi snd_seq snd_seq_device iTCO_wdt snd_timer iTCO_vendor_support coretemp parport_pc i2c_algo_bit crc32c_intel snd parport evdev i2c_i801 i2c_core pcspkr mperf ghash_clmulni_intel processor cryptd soundcore thermal_sys button ext4 crc16 jbd2 mbcache btrfs crc32c libcrc32c zlib_deflate sg sr_mod cdrom sd_mod crc_t10dif usbhid hid ahci libahci ehci_hcd atl1c libata usbcore scsi_mod usb_common ** PCI devices: 00:00.0 Host bridge [0600]: Intel Corporation 2nd Generation Core Processor Family DRAM Controller [8086:0100] (rev 09) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 0 Capabilities: <access denied> Kernel driver in use: agpgart-intel 00:02.0 VGA compatible controller [0300]: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller [8086:0102] (rev 09) (prog-if 00 [VGA controller]) Subsystem: Giga-byte Technology Device [1458:d000] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 41 Region 0: Memory at fb800000 (64-bit, non-prefetchable) [size=4M] Region 2: Memory at e0000000 (64-bit, prefetchable) [size=256M] Region 4: I/O ports at ff00 [size=64] Expansion ROM at <unassigned> [disabled] Capabilities: <access denied> Kernel driver in use: i915 00:16.0 Communication controller [0780]: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 [8086:1c3a] (rev 04) Subsystem: Giga-byte Technology Device [1458:1c3a] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 10 Region 0: Memory at fbfff000 (64-bit, non-prefetchable) [size=16] Capabilities: <access denied> 00:1a.0 USB controller [0c03]: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 [8086:1c2d] (rev 05) (prog-if 20 [EHCI]) Subsystem: Giga-byte Technology Device [1458:5006] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin C routed to IRQ 18 Region 0: Memory at fbffe000 (32-bit, non-prefetchable) [size=1K] Capabilities: <access denied> Kernel driver in use: ehci_hcd 00:1b.0 Audio device [0403]: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller [8086:1c20] (rev 05) Subsystem: Giga-byte Technology Device [1458:a002] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 4 bytes Interrupt: pin A routed to IRQ 42 Region 0: Memory at fbff4000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: snd_hda_intel 00:1c.0 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 [8086:1c10] (rev b5) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 4 bytes Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 00002000-00002fff Memory behind bridge: dfa00000-dfbfffff Prefetchable memory behind bridge: 00000000dfc00000-00000000dfdfffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport 00:1c.1 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev b5) (prog-if 01 [Subtractive decode]) Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 4 bytes Bus: primary=00, secondary=02, subordinate=03, sec-latency=0 Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> 00:1c.4 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 5 [8086:1c18] (rev b5) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 4 bytes Bus: primary=00, secondary=04, subordinate=04, sec-latency=0 I/O behind bridge: 0000e000-0000efff Memory behind bridge: fbe00000-fbefffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport 00:1d.0 USB controller [0c03]: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 [8086:1c26] (rev 05) (prog-if 20 [EHCI]) Subsystem: Giga-byte Technology Device [1458:5006] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 23 Region 0: Memory at fbffd000 (32-bit, non-prefetchable) [size=1K] Capabilities: <access denied> Kernel driver in use: ehci_hcd 00:1f.0 ISA bridge [0601]: Intel Corporation H61 Express Chipset Family LPC Controller [8086:1c5c] (rev 05) Subsystem: Giga-byte Technology Device [1458:5001] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Capabilities: <access denied> 00:1f.2 SATA controller [0106]: Intel Corporation 6 Series/C200 Series Chipset Family SATA AHCI Controller [8086:1c02] (rev 05) (prog-if 01 [AHCI 1.0]) Subsystem: Giga-byte Technology Device [1458:b005] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 40 Region 0: I/O ports at fe00 [size=8] Region 1: I/O ports at fd00 [size=4] Region 2: I/O ports at fc00 [size=8] Region 3: I/O ports at fb00 [size=4] Region 4: I/O ports at fa00 [size=32] Region 5: Memory at fbffc000 (32-bit, non-prefetchable) [size=2K] Capabilities: <access denied> Kernel driver in use: ahci 00:1f.3 SMBus [0c05]: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller [8086:1c22] (rev 05) Subsystem: Giga-byte Technology Device [1458:5001] Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin C routed to IRQ 18 Region 0: Memory at fbffb000 (64-bit, non-prefetchable) [size=256] Region 4: I/O ports at 0500 [size=32] Kernel driver in use: i801_smbus 02:00.0 PCI bridge [0604]: Integrated Technology Express, Inc. Device [1283:8892] (rev 30) (prog-if 01 [Subtractive decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 4 bytes Bus: primary=02, secondary=03, subordinate=03, sec-latency=32 Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr+ DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> 04:00.0 Ethernet controller [0200]: Atheros Communications Inc. AR8151 v2.0 Gigabit Ethernet [1969:1083] (rev c0) Subsystem: Giga-byte Technology Device [1458:e000] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 4 bytes Interrupt: pin A routed to IRQ 43 Region 0: Memory at fbec0000 (64-bit, non-prefetchable) [size=256K] Region 2: I/O ports at ef00 [size=128] Capabilities: <access denied> Kernel driver in use: atl1c ** USB devices: Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 003: ID 046d:c06a Logitech, Inc. -- System Information: Debian Release: 7.0 APT prefers testing APT policy: (500, 'testing'), (500, 'stable') Architecture: amd64 (x86_64) Foreign Architectures: i386 Kernel: Linux 3.2.0-4-amd64 (SMP w/2 CPU cores) Locale: LANG=C, LC_CTYPE=C (charmap=ANSI_X3.4-1968) Shell: /bin/sh linked to /bin/dash Versions of packages linux-image-3.2.0-4-amd64 depends on: ii debconf [debconf-2.0] 1.5.49 ii initramfs-tools [linux-initramfs-tool] 0.109.1 ii kmod 9-2 ii linux-base 3.5 ii module-init-tools 9-2 Versions of packages linux-image-3.2.0-4-amd64 recommends: ii firmware-linux-free 3.2 Versions of packages linux-image-3.2.0-4-amd64 suggests: pn debian-kernel-handbook <none> ii grub-pc 1.99-27 pn linux-doc-3.2 <none> Versions of packages linux-image-3.2.0-4-amd64 is related to: pn firmware-atheros <none> pn firmware-bnx2 <none> pn firmware-bnx2x <none> pn firmware-brcm80211 <none> pn firmware-intelwimax <none> pn firmware-ipw2x00 <none> pn firmware-ivtv <none> pn firmware-iwlwifi <none> pn firmware-libertas <none> pn firmware-linux <none> ii firmware-linux-nonfree 0.36+wheezy.1 pn firmware-myricom <none> pn firmware-netxen <none> pn firmware-qlogic <none> pn firmware-ralink <none> pn firmware-realtek <none> pn xen-hypervisor <none> -- debconf information: linux-image-3.2.0-4-amd64/postinst/ignoring-ramdisk: linux-image-3.2.0-4-amd64/postinst/depmod-error-initrd-3.2.0-4-amd64: false linux-image-3.2.0-4-amd64/prerm/removing-running-kernel-3.2.0-4-amd64: true linux-image-3.2.0-4-amd64/postinst/missing-firmware-3.2.0-4-amd64: -- To UNSUBSCRIBE, email to debian-kernel-requ...@lists.debian.org with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org Archive: http://lists.debian.org/20130428190603.5115.41028.reportbug@localhost