Package: src:linux Version: 3.16.7-ckt11-1 Severity: important Dear Maintainer,
my motherboard is a asus rampage 2 extreme it have a pci-e 2.0 and my graphics card is a geforce gtx 670, pci 3.0. since i have install this graphics card i have this warnings on my /var/log/messages May 19 09:52:26 debian kernel: [ 8.474107] ACPI Warning: SystemIO range 0x0000000000000828-0x000000000000082f conflicts with OpRegion 0x0000000000000800-0x000000000000084f (\PMRG) (20140424/utaddress-258) May 19 09:52:26 debian kernel: [ 8.474113] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver May 19 09:52:26 debian kernel: [ 8.474116] ACPI Warning: SystemIO range 0x0000000000000530-0x000000000000053f conflicts with OpRegion 0x0000000000000500-0x000000000000053f (\GPS0) (20140424/utaddress-258) May 19 09:52:26 debian kernel: [ 8.474118] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver May 19 09:52:26 debian kernel: [ 8.474119] ACPI Warning: SystemIO range 0x0000000000000500-0x000000000000052f conflicts with OpRegion 0x0000000000000500-0x000000000000050f (\SBG6) (20140424/utaddress-258) May 19 09:52:26 debian kernel: [ 8.474122] ACPI Warning: SystemIO range 0x0000000000000500-0x000000000000052f conflicts with OpRegion 0x0000000000000500-0x000000000000053f (\GPS0) (20140424/utaddress-258) May 19 09:52:26 debian kernel: [ 8.474124] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver May 19 09:52:26 debian kernel: [ 8.474125] lpc_ich: Resource conflict(s) found affecting gpio_ich May 19 09:52:26 debian kernel: [ 8.512924] EDAC MC: Ver: 3.0.0 -- Package-specific info: ** Version: Linux version 3.16.0-4-amd64 (debian-kernel@lists.debian.org) (gcc version 4.8.4 (Debian 4.8.4-1) ) #1 SMP Debian 3.16.7-ckt11-1 (2015-05-24) ** Command line: BOOT_IMAGE=/boot/vmlinuz-3.16.0-4-amd64 root=UUID=34225ba4-9b9f-4178-877d-43845ae20868 ro quiet ** Tainted: O (4096) * Out-of-tree module has been loaded. ** Kernel log: [ 9.937039] input: HDA Intel Line Out CLFE as /devices/pci0000:00/0000:00:1b.0/sound/card0/input13 [ 9.937123] input: HDA Intel Line Out Side as /devices/pci0000:00/0000:00:1b.0/sound/card0/input14 [ 9.937196] input: HDA Intel Front Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input15 [ 9.992159] b2c2-flexcop: ISL6421 successfully attached [ 10.046788] MXM: GUID detected in BIOS [ 10.047130] nouveau [ DEVICE][0000:02:00.0] BOOT0 : 0x0e4090a2 [ 10.047134] nouveau [ DEVICE][0000:02:00.0] Chipset: GK104 (NVE4) [ 10.047137] nouveau [ DEVICE][0000:02:00.0] Family : NVE0 [ 10.047195] nouveau [ VBIOS][0000:02:00.0] checking PRAMIN for image... [ 10.047201] nouveau [ VBIOS][0000:02:00.0] ... signature not found [ 10.047203] nouveau [ VBIOS][0000:02:00.0] checking PROM for image... [ 10.084302] nouveau [ VBIOS][0000:02:00.0] ... appears to be valid [ 10.084304] nouveau [ VBIOS][0000:02:00.0] using image from PROM [ 10.084407] nouveau [ VBIOS][0000:02:00.0] BIT signature found [ 10.084409] nouveau [ VBIOS][0000:02:00.0] version 80.04.4b.00.24 [ 10.084780] nouveau 0000:02:00.0: irq 70 for MSI/MSI-X [ 10.084788] nouveau [ PMC][0000:02:00.0] MSI interrupts enabled [ 10.084829] nouveau [ PFB][0000:02:00.0] RAM type: GDDR5 [ 10.084831] nouveau [ PFB][0000:02:00.0] RAM size: 2048 MiB [ 10.084832] nouveau [ PFB][0000:02:00.0] ZCOMP: 0 tags [ 10.084891] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro [ 10.089121] nouveau [ VOLT][0000:02:00.0] GPU voltage: 987500uv [ 10.117511] nouveau [ PTHERM][0000:02:00.0] FAN control: PWM [ 10.117521] nouveau [ PTHERM][0000:02:00.0] fan management: automatic [ 10.117533] nouveau [ PTHERM][0000:02:00.0] internal sensor: yes [ 10.117563] nouveau [ CLK][0000:02:00.0] 07: core 324 MHz memory 648 MHz [ 10.117595] nouveau [ CLK][0000:02:00.0] 0a: core 324-862 MHz memory 1620 MHz [ 10.117676] nouveau [ CLK][0000:02:00.0] 0d: core 540-1202 MHz memory 6008 MHz [ 10.117774] nouveau [ CLK][0000:02:00.0] 0f: core 540-1202 MHz memory 6008 MHz [ 10.117850] nouveau [ CLK][0000:02:00.0] --: core 324 MHz memory 648 MHz [ 10.136202] input: HDA NVidia HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:03.0/0000:02:00.1/sound/card1/input16 [ 10.136300] input: HDA NVidia HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:03.0/0000:02:00.1/sound/card1/input17 [ 10.136387] input: HDA NVidia HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:03.0/0000:02:00.1/sound/card1/input18 [ 10.136492] input: HDA NVidia HDMI/DP,pcm=9 as /devices/pci0000:00/0000:00:03.0/0000:02:00.1/sound/card1/input19 [ 10.191972] ITD1000: successfully identified (ID: 0) [ 10.210180] [TTM] Zone kernel: Available graphics memory: 3059660 kiB [ 10.210182] [TTM] Zone dma32: Available graphics memory: 2097152 kiB [ 10.210183] [TTM] Initializing pool allocator [ 10.210188] [TTM] Initializing DMA pool allocator [ 10.210199] nouveau [ DRM] VRAM: 2048 MiB [ 10.210200] nouveau [ DRM] GART: 1048576 MiB [ 10.210204] nouveau [ DRM] TMDS table version 2.0 [ 10.210205] nouveau [ DRM] DCB version 4.0 [ 10.210207] nouveau [ DRM] DCB outp 00: 01000f02 00020030 [ 10.210209] nouveau [ DRM] DCB outp 01: 02000f00 00000000 [ 10.210211] nouveau [ DRM] DCB outp 02: 08011f82 00020030 [ 10.210212] nouveau [ DRM] DCB outp 03: 02822f62 0f420010 [ 10.210213] nouveau [ DRM] DCB outp 05: 04833fb6 0f420010 [ 10.210214] nouveau [ DRM] DCB outp 06: 04033f72 00020010 [ 10.210216] nouveau [ DRM] DCB conn 00: 00001030 [ 10.210217] nouveau [ DRM] DCB conn 01: 00020131 [ 10.210219] nouveau [ DRM] DCB conn 02: 00002261 [ 10.210220] nouveau [ DRM] DCB conn 03: 00010346 [ 10.210221] nouveau [ DRM] DCB conn 04: 00000460 [ 10.211686] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 10.211688] [drm] Driver supports precise vblank timestamp query. [ 10.225821] b2c2-flexcop: ITD1000 successfully attached [ 10.225823] b2c2-flexcop: found 'Samsung S5H1420/PnpNetwork PN1010 DVB-S' . [ 10.225827] b2c2_flexcop_pci 0000:07:00.0: DVB: registering adapter 0 frontend 0 (Samsung S5H1420/PnpNetwork PN1010 DVB-S)... [ 10.225987] b2c2-flexcop: initialization of 'Sky2PC/SkyStar 2 DVB-S rev 2.7a/u' at the 'PCI' bus controlled by a 'FlexCopIIb' complete [ 10.228148] nouveau [ DRM] MM: using COPY for buffer copies [ 10.273307] systemd-journald[234]: Received request to flush runtime journal from PID 1 [ 10.302682] Adding 12564476k swap on /dev/sda5. Priority:-1 extents:1 across:12564476k FS [ 10.444366] nouveau [ DRM] allocated 1680x1050 fb: 0x80000, bo ffff8801b64d1c00 [ 10.444474] fbcon: nouveaufb (fb0) is primary device [ 10.682659] Console: switching to colour frame buffer device 210x65 [ 10.683437] nouveau 0000:02:00.0: fb0: nouveaufb frame buffer device [ 10.683437] nouveau 0000:02:00.0: registered panic notifier [ 10.692455] [drm] Initialized nouveau 1.1.2 20120801 for 0000:02:00.0 on minor 0 [ 11.104768] Bluetooth: Core ver 2.19 [ 11.104781] NET: Registered protocol family 31 [ 11.104782] Bluetooth: HCI device and connection manager initialized [ 11.104788] Bluetooth: HCI socket layer initialized [ 11.104790] Bluetooth: L2CAP socket layer initialized [ 11.104797] Bluetooth: SCO socket layer initialized [ 11.157499] usbcore: registered new interface driver btusb [ 12.430323] systemd-journald[234]: Received request to flush runtime journal from PID 1 [ 12.747176] RPC: Registered named UNIX socket transport module. [ 12.747179] RPC: Registered udp transport module. [ 12.747180] RPC: Registered tcp transport module. [ 12.747181] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 12.776217] FS-Cache: Loaded [ 12.829924] FS-Cache: Netfs 'nfs' registered for caching [ 12.846095] Installing knfsd (copyright (C) 1996 o...@monad.swb.de). [ 13.687516] input: PS/2 Generic Mouse as /devices/platform/i8042/serio1/input/input6 [ 13.934077] vboxdrv: Found 8 processor cores. [ 13.934399] vboxdrv: fAsync=0 offMin=0x200 offMax=0x5515 [ 13.934468] vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'. [ 13.934469] vboxdrv: Successfully loaded version 4.3.28_Debian (interface 0x001a000a). [ 14.713646] vboxpci: IOMMU not found (not registered) [ 17.386642] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 17.386644] Bluetooth: BNEP filters: protocol multicast [ 17.386651] Bluetooth: BNEP socket layer initialized [ 20.012689] sky2 0000:05:00.0 eth0: enabling interface [ 20.012763] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 22.322351] sky2 0000:05:00.0 eth0: Link is up at 1000 Mbps, full duplex, flow control both [ 22.322386] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 42.974636] Bluetooth: RFCOMM TTY layer initialized [ 42.974649] Bluetooth: RFCOMM socket layer initialized [ 42.974655] Bluetooth: RFCOMM ver 1.11 ** Model information sys_vendor: System manufacturer product_name: System Product Name product_version: System Version chassis_vendor: Chassis Manufacture chassis_version: Chassis Version bios_vendor: American Megatrends Inc. bios_version: 2101 board_vendor: ASUSTeK Computer INC. board_name: Rampage II Extreme board_version: Rev 2.xx ** Loaded modules: rfcomm binfmt_misc bnep pci_stub vboxpci(O) vboxnetadp(O) vboxnetflt(O) vboxdrv(O) nfsd auth_rpcgss oid_registry nfs_acl nfs lockd fscache sunrpc ecb btusb bluetooth 6lowpan_iphc rfkill itd1000 nouveau isl6421 snd_hda_codec_analog snd_hda_codec_generic snd_hda_codec_hdmi coretemp video b2c2_flexcop_pci kvm_intel b2c2_flexcop kvm snd_hda_intel s5h1420 cx24113 cx24123 dvb_core snd_hda_controller mxm_wmi evdev iTCO_wdt iTCO_vendor_support psmouse ttm serio_raw drm_kms_helper drm snd_hda_codec pcspkr i2c_algo_bit snd_hwdep snd_pcm snd_timer lpc_ich shpchp wmi i2c_i801 mfd_core i2c_core i7core_edac snd button edac_core soundcore asus_atk0110 acpi_cpufreq processor thermal_sys fuse parport_pc ppdev lp parport autofs4 ext4 crc16 mbcache jbd2 sg sd_mod crc_t10dif sr_mod crct10dif_generic cdrom crct10dif_common hid_generic usbhid hid firewire_ohci firewire_core crc32c_intel ahci libahci libata uhci_hcd ehci_pci ehci_hcd crc_itu_t scsi_mod sky2 usbcore usb_common floppy ** PCI devices: 00:00.0 Host bridge [0600]: Intel Corporation 5520/5500/X58 I/O Hub to ESI Port [8086:3405] (rev 13) Subsystem: ASUSTeK Computer Inc. Device [1043:836b] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Capabilities: <access denied> 00:01.0 PCI bridge [0604]: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 1 [8086:3408] (rev 13) (prog-if 00 [Normal decode]) Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 256 bytes Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport 00:03.0 PCI bridge [0604]: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 3 [8086:340a] (rev 13) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 256 bytes Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 I/O behind bridge: 0000c000-0000cfff Memory behind bridge: fa000000-fbcfffff Prefetchable memory behind bridge: 00000000d6000000-00000000dfffffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport 00:07.0 PCI bridge [0604]: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 7 [8086:340e] (rev 13) (prog-if 00 [Normal decode]) Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 256 bytes Bus: primary=00, secondary=03, subordinate=03, sec-latency=0 Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport 00:14.0 PIC [0800]: Intel Corporation 7500/5520/5500/X58 I/O Hub System Management Registers [8086:342e] (rev 13) (prog-if 00 [8259]) Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Capabilities: <access denied> Kernel driver in use: i7core_edac 00:14.1 PIC [0800]: Intel Corporation 7500/5520/5500/X58 I/O Hub GPIO and Scratch Pad Registers [8086:3422] (rev 13) (prog-if 00 [8259]) Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Capabilities: <access denied> 00:14.2 PIC [0800]: Intel Corporation 7500/5520/5500/X58 I/O Hub Control Status and RAS Registers [8086:3423] (rev 13) (prog-if 00 [8259]) Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Capabilities: <access denied> 00:14.3 PIC [0800]: Intel Corporation 7500/5520/5500/X58 I/O Hub Throttle Registers [8086:3438] (rev 13) (prog-if 00 [8259]) Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00:1a.0 USB controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #4 [8086:3a37] (prog-if 00 [UHCI]) Subsystem: ASUSTeK Computer Inc. P5Q Deluxe Motherboard [1043:82d4] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 4: I/O ports at b800 [size=32] Capabilities: <access denied> Kernel driver in use: uhci_hcd 00:1a.1 USB controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #5 [8086:3a38] (prog-if 00 [UHCI]) Subsystem: ASUSTeK Computer Inc. P5Q Deluxe Motherboard [1043:82d4] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 21 Region 4: I/O ports at b880 [size=32] Capabilities: <access denied> Kernel driver in use: uhci_hcd 00:1a.2 USB controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #6 [8086:3a39] (prog-if 00 [UHCI]) Subsystem: ASUSTeK Computer Inc. P5Q Deluxe Motherboard [1043:82d4] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin D routed to IRQ 19 Region 4: I/O ports at bc00 [size=32] Capabilities: <access denied> Kernel driver in use: uhci_hcd 00:1a.7 USB controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #2 [8086:3a3c] (prog-if 20 [EHCI]) Subsystem: ASUSTeK Computer Inc. P5Q Deluxe Motherboard [1043:82d4] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin C routed to IRQ 18 Region 0: Memory at f9fff000 (32-bit, non-prefetchable) [size=1K] Capabilities: <access denied> Kernel driver in use: ehci-pci 00:1b.0 Audio device [0403]: Intel Corporation 82801JI (ICH10 Family) HD Audio Controller [8086:3a3e] Subsystem: ASUSTeK Computer Inc. Device [1043:82ea] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 256 bytes Interrupt: pin A routed to IRQ 69 Region 0: Memory at f9ff8000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: snd_hda_intel 00:1c.0 PCI bridge [0604]: Intel Corporation 82801JI (ICH10 Family) PCI Express Root Port 1 [8086:3a40] (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 256 bytes Bus: primary=00, secondary=06, subordinate=06, sec-latency=0 I/O behind bridge: 00001000-00001fff Memory behind bridge: c0000000-c03fffff Prefetchable memory behind bridge: 00000000f8f00000-00000000f8ffffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport 00:1c.2 PCI bridge [0604]: Intel Corporation 82801JI (ICH10 Family) PCI Express Root Port 3 [8086:3a44] (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 256 bytes Bus: primary=00, secondary=05, subordinate=05, sec-latency=0 I/O behind bridge: 0000d000-0000dfff Memory behind bridge: fbd00000-fbdfffff Prefetchable memory behind bridge: 00000000c0400000-00000000c05fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport 00:1c.4 PCI bridge [0604]: Intel Corporation 82801JI (ICH10 Family) PCI Express Root Port 5 [8086:3a48] (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 256 bytes Bus: primary=00, secondary=04, subordinate=04, sec-latency=0 I/O behind bridge: 00002000-00002fff Memory behind bridge: c0600000-c09fffff Prefetchable memory behind bridge: 00000000f8e00000-00000000f8efffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport 00:1d.0 USB controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #1 [8086:3a34] (prog-if 00 [UHCI]) Subsystem: ASUSTeK Computer Inc. P5Q Deluxe Motherboard [1043:82d4] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 23 Region 4: I/O ports at b080 [size=32] Capabilities: <access denied> Kernel driver in use: uhci_hcd 00:1d.1 USB controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #2 [8086:3a35] (prog-if 00 [UHCI]) Subsystem: ASUSTeK Computer Inc. P5Q Deluxe Motherboard [1043:82d4] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 19 Region 4: I/O ports at b400 [size=32] Capabilities: <access denied> Kernel driver in use: uhci_hcd 00:1d.2 USB controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #3 [8086:3a36] (prog-if 00 [UHCI]) Subsystem: ASUSTeK Computer Inc. P5Q Deluxe Motherboard [1043:82d4] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin C routed to IRQ 18 Region 4: I/O ports at b480 [size=32] Capabilities: <access denied> Kernel driver in use: uhci_hcd 00:1d.7 USB controller [0c03]: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #1 [8086:3a3a] (prog-if 20 [EHCI]) Subsystem: ASUSTeK Computer Inc. P5Q Deluxe Motherboard [1043:82d4] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 23 Region 0: Memory at f9ffe000 (32-bit, non-prefetchable) [size=1K] Capabilities: <access denied> Kernel driver in use: ehci-pci 00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev 90) (prog-if 01 [Subtractive decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Bus: primary=00, secondary=07, subordinate=07, sec-latency=32 I/O behind bridge: 0000e000-0000efff Memory behind bridge: fbe00000-fbefffff Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> 00:1f.0 ISA bridge [0601]: Intel Corporation 82801JIR (ICH10R) LPC Interface Controller [8086:3a16] Subsystem: ASUSTeK Computer Inc. P5Q Deluxe Motherboard [1043:82d4] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Capabilities: <access denied> Kernel driver in use: lpc_ich 00:1f.2 SATA controller [0106]: Intel Corporation 82801JI (ICH10 Family) SATA AHCI Controller [8086:3a22] (prog-if 01 [AHCI 1.0]) Subsystem: ASUSTeK Computer Inc. P5Q Deluxe Motherboard [1043:82d4] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 68 Region 0: I/O ports at ac00 [size=8] Region 1: I/O ports at a880 [size=4] Region 2: I/O ports at a800 [size=8] Region 3: I/O ports at a480 [size=4] Region 4: I/O ports at a400 [size=32] Region 5: Memory at f9ffc000 (32-bit, non-prefetchable) [size=2K] Capabilities: <access denied> Kernel driver in use: ahci 00:1f.3 SMBus [0c05]: Intel Corporation 82801JI (ICH10 Family) SMBus Controller [8086:3a30] Subsystem: ASUSTeK Computer Inc. P5Q Deluxe Motherboard [1043:82d4] Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin C routed to IRQ 18 Region 0: Memory at f9ffd000 (64-bit, non-prefetchable) [size=256] Region 4: I/O ports at 0400 [size=32] 02:00.0 VGA compatible controller [0300]: NVIDIA Corporation GK104 [GeForce GTX 670] [10de:1189] (rev a1) (prog-if 00 [VGA controller]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 256 bytes Interrupt: pin A routed to IRQ 70 Region 0: Memory at fa000000 (32-bit, non-prefetchable) [size=16M] Region 1: Memory at d8000000 (64-bit, prefetchable) [size=128M] Region 3: Memory at d6000000 (64-bit, prefetchable) [size=32M] Region 5: I/O ports at cc00 [size=128] Expansion ROM at fbc00000 [disabled] [size=512K] Capabilities: <access denied> Kernel driver in use: nouveau 02:00.1 Audio device [0403]: NVIDIA Corporation GK104 HDMI Audio Controller [10de:0e0a] (rev a1) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 256 bytes Interrupt: pin B routed to IRQ 34 Region 0: Memory at fbcfc000 (32-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: snd_hda_intel 05:00.0 Ethernet controller [0200]: Marvell Technology Group Ltd. 88E8056 PCI-E Gigabit Ethernet Controller [11ab:4364] (rev 12) Subsystem: ASUSTeK Computer Inc. Motherboard [1043:81f8] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 256 bytes Interrupt: pin A routed to IRQ 67 Region 0: Memory at fbdfc000 (64-bit, non-prefetchable) [size=16K] Region 2: I/O ports at d800 [size=256] Expansion ROM at fbdc0000 [disabled] [size=128K] Capabilities: <access denied> Kernel driver in use: sky2 07:00.0 Network controller [0280]: Techsan Electronics Co Ltd B2C2 FlexCopII DVB chip / Technisat SkyStar2 DVB card [13d0:2103] (rev 02) Subsystem: Techsan Electronics Co Ltd B2C2 FlexCopII DVB chip / Technisat SkyStar2 DVB card [13d0:2103] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 Interrupt: pin A routed to IRQ 16 Region 0: Memory at fbef0000 (32-bit, non-prefetchable) [size=64K] Region 1: I/O ports at ec00 [size=32] Kernel driver in use: b2c2_flexcop_pci 07:02.0 FireWire (IEEE 1394) [0c00]: VIA Technologies, Inc. VT6306/7/8 [Fire II(M)] IEEE 1394 OHCI Controller [1106:3044] (rev c0) (prog-if 10 [OHCI]) Subsystem: ASUSTeK Computer Inc. Motherboard [1043:81fe] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 (8000ns max), Cache Line Size: 256 bytes Interrupt: pin A routed to IRQ 18 Region 0: Memory at fbeef000 (32-bit, non-prefetchable) [size=2K] Region 1: I/O ports at e880 [size=128] Capabilities: <access denied> Kernel driver in use: firewire_ohci ff:00.0 Host bridge [0600]: Intel Corporation Xeon 5500/Core i7 QuickPath Architecture Generic Non-Core Registers [8086:2c41] (rev 05) Subsystem: Intel Corporation Device [8086:8086] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 ff:00.1 Host bridge [0600]: Intel Corporation Xeon 5500/Core i7 QuickPath Architecture System Address Decoder [8086:2c01] (rev 05) Subsystem: Intel Corporation Device [8086:8086] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 ff:02.0 Host bridge [0600]: Intel Corporation Xeon 5500/Core i7 QPI Link 0 [8086:2c10] (rev 05) Subsystem: Intel Corporation Device [8086:8086] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 ff:02.1 Host bridge [0600]: Intel Corporation Xeon 5500/Core i7 QPI Physical 0 [8086:2c11] (rev 05) Subsystem: Intel Corporation Device [8086:8086] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 ff:03.0 Host bridge [0600]: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller [8086:2c18] (rev 05) Subsystem: Intel Corporation Device [8086:8086] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 ff:03.1 Host bridge [0600]: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Target Address Decoder [8086:2c19] (rev 05) Subsystem: Intel Corporation Device [8086:8086] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 ff:03.4 Host bridge [0600]: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Test Registers [8086:2c1c] (rev 05) Subsystem: Intel Corporation Device [8086:8086] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 ff:04.0 Host bridge [0600]: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Channel 0 Control Registers [8086:2c20] (rev 05) Subsystem: Intel Corporation Device [8086:8086] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 ff:04.1 Host bridge [0600]: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Channel 0 Address Registers [8086:2c21] (rev 05) Subsystem: Intel Corporation Device [8086:8086] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 ff:04.2 Host bridge [0600]: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Channel 0 Rank Registers [8086:2c22] (rev 05) Subsystem: Intel Corporation Device [8086:8086] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 ff:04.3 Host bridge [0600]: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Channel 0 Thermal Control Registers [8086:2c23] (rev 05) Subsystem: Intel Corporation Device [8086:8086] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 ff:05.0 Host bridge [0600]: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Channel 1 Control Registers [8086:2c28] (rev 05) Subsystem: Intel Corporation Device [8086:8086] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 ff:05.1 Host bridge [0600]: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Channel 1 Address Registers [8086:2c29] (rev 05) Subsystem: Intel Corporation Device [8086:8086] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 ff:05.2 Host bridge [0600]: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Channel 1 Rank Registers [8086:2c2a] (rev 05) Subsystem: Intel Corporation Device [8086:8086] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 ff:05.3 Host bridge [0600]: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Channel 1 Thermal Control Registers [8086:2c2b] (rev 05) Subsystem: Intel Corporation Device [8086:8086] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 ff:06.0 Host bridge [0600]: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Channel 2 Control Registers [8086:2c30] (rev 05) Subsystem: Intel Corporation Device [8086:8086] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 ff:06.1 Host bridge [0600]: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Channel 2 Address Registers [8086:2c31] (rev 05) Subsystem: Intel Corporation Device [8086:8086] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 ff:06.2 Host bridge [0600]: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Channel 2 Rank Registers [8086:2c32] (rev 05) Subsystem: Intel Corporation Device [8086:8086] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 ff:06.3 Host bridge [0600]: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Channel 2 Thermal Control Registers [8086:2c33] (rev 05) Subsystem: Intel Corporation Device [8086:8086] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 ** USB devices: Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 008 Device 002: ID 0b05:17cb ASUSTek Computer, Inc. Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 002: ID 046d:c05a Logitech, Inc. M90/M100 Optical Mouse Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub -- System Information: Debian Release: stretch/sid APT prefers testing-updates APT policy: (500, 'testing-updates'), (500, 'testing') Architecture: amd64 (x86_64) Foreign Architectures: i386 Kernel: Linux 3.16.0-4-amd64 (SMP w/8 CPU cores) Locale: LANG=de_DE.UTF-8, LC_CTYPE=de_DE.UTF-8 (charmap=UTF-8) Shell: /bin/sh linked to /bin/dash Init: systemd (via /run/systemd/system) Versions of packages linux-image-3.16.0-4-amd64 depends on: ii debconf [debconf-2.0] 1.5.56 ii initramfs-tools [linux-initramfs-tool] 0.120 ii kmod 20-1 ii linux-base 3.5 Versions of packages linux-image-3.16.0-4-amd64 recommends: pn firmware-linux-free <none> pn irqbalance <none> Versions of packages linux-image-3.16.0-4-amd64 suggests: pn debian-kernel-handbook <none> ii grub-pc 2.02~beta2-23 pn linux-doc-3.16 <none> Versions of packages linux-image-3.16.0-4-amd64 is related to: pn firmware-atheros <none> pn firmware-bnx2 <none> pn firmware-bnx2x <none> pn firmware-brcm80211 <none> pn firmware-intelwimax <none> pn firmware-ipw2x00 <none> pn firmware-ivtv <none> pn firmware-iwlwifi <none> pn firmware-libertas <none> pn firmware-linux <none> pn firmware-linux-nonfree <none> pn firmware-myricom <none> pn firmware-netxen <none> pn firmware-qlogic <none> pn firmware-ralink <none> pn firmware-realtek <none> pn xen-hypervisor <none> -- debconf information: linux-image-3.16.0-4-amd64/postinst/depmod-error-initrd-3.16.0-4-amd64: false linux-image-3.16.0-4-amd64/postinst/mips-initrd-3.16.0-4-amd64: linux-image-3.16.0-4-amd64/prerm/removing-running-kernel-3.16.0-4-amd64: true -- To UNSUBSCRIBE, email to debian-kernel-requ...@lists.debian.org with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org Archive: https://lists.debian.org/20150610080202.1926.46082.reportbug@debian