Bonjour, J'ai installe etch, sur un PIII, avec carte scsi 29160 adaptec ( 3 DD de 9 Go en sus de 2 DD ide ), sur une carte mère msi 694T pro ! Quand je monte un DD en USB sa rame terrible, il tente d'utiliser la carte scsi ! Comment remedier au Probleme de la lenteur ? ( faut charger un autre module ?, je souhaite éviter une compile noyeau )
Merci Tous mes voeux ..... ( plein de bonnes choses ) Ptilou l'erreur dans le dmesg : Initializing USB Mass Storage driver... scsi1 : SCSI emulation for USB Mass Storage devices usbcore: registered new driver usb-storage USB Mass Storage support registered. usb-storage: device found at 2 usb-storage: waiting for device to settle before scanning sd 0:0:11:0: Attempting to queue an ABORT message CDB: 0x12 0x1 0x0 0x0 0xfe 0x0 sd 0:0:11:0: Command already completed aic7xxx_abort returns 0x2002 Vendor: HDS72808 Model: 0PLAT20 Rev: PF2O Type: Direct-Access ANSI SCSI revision: 00 SCSI device sdd: 160836479 512-byte hdwr sectors (82348 MB) sdd: Write Protect is off sdd: Mode Sense: 03 00 00 00 sdd: assuming drive cache: write through SCSI device sdd: 160836479 512-byte hdwr sectors (82348 MB) sdd: Write Protect is off sdd: Mode Sense: 03 00 00 00 sdd: assuming drive cache: write through sdd: sdd2 sd 1:0:0:0: Attached scsi disk sdd usb-storage: device scan complete sd 0:0:11:0: Attempting to queue an ABORT message CDB: 0x0 0x0 0x0 0x0 0x0 0x0 sd 0:0:11:0: Command already completed aic7xxx_abort returns 0x2002 sd 0:0:10:0: Attempting to queue an ABORT message CDB: 0x12 0x1 0x0 0x0 0xfe 0x0 sd 0:0:10:0: Command not found aic7xxx_abort returns 0x2002 sd 0:0:10:0: Attempting to queue an ABORT message CDB: 0x0 0x0 0x0 0x0 0x0 0x0 sd 0:0:10:0: Command already completed aic7xxx_abort returns 0x2002 sd 0:0:8:0: Attempting to queue an ABORT message CDB: 0x12 0x1 0x0 0x0 0xfe 0x0 sd 0:0:8:0: Command not found aic7xxx_abort returns 0x2002 sd 0:0:8:0: Attempting to queue an ABORT message CDB: 0x0 0x0 0x0 0x0 0x0 0x0 sd 0:0:8:0: Command already completed aic7xxx_abort returns 0x2002 sd 0:0:8:0: Attempting to queue a TARGET RESET message CDB: 0x12 0x1 0x0 0x0 0xfe 0x0 sd 0:0:8:0: Command not found aic7xxx_dev_reset returns 0x2002 sd 0:0:8:0: Attempting to queue an ABORT message CDB: 0x0 0x0 0x0 0x0 0x0 0x0 sd 0:0:8:0: Command already completed aic7xxx_abort returns 0x2002 sd 0:0:10:0: Attempting to queue a TARGET RESET message CDB: 0x12 0x1 0x0 0x0 0xfe 0x0 sd 0:0:10:0: Command not found aic7xxx_dev_reset returns 0x2002 sd 0:0:10:0: Attempting to queue an ABORT message CDB: 0x0 0x0 0x0 0x0 0x0 0x0 sd 0:0:10:0: Command already completed aic7xxx_abort returns 0x2002 sd 0:0:11:0: Attempting to queue a TARGET RESET message CDB: 0x12 0x1 0x0 0x0 0xfe 0x0 sd 0:0:11:0: Command not found aic7xxx_dev_reset returns 0x2002 sd 0:0:11:0: Attempting to queue an ABORT message CDB: 0x0 0x0 0x0 0x0 0x0 0x0 sd 0:0:11:0: Command already completed aic7xxx_abort returns 0x2002 sd 0:0:11:0: Attempting to queue an ABORT message CDB: 0x0 0x0 0x0 0x0 0x0 0x0 scsi0: At time of recovery, card was paused
Dump Card State Begins <<<<<<<<<<<<<<<<<
scsi0: Dumping Card State in Message-out phase, at SEQADDR 0x16c Card was paused ACCUM = 0xa0, SINDEX = 0x61, DINDEX = 0xe4, ARG_2 = 0x0 HCNT = 0x0 SCBPTR = 0x1 SCSIPHASE[0x4]:(MSG_OUT_PHASE) SCSISIGI[0xb6]:(REQI|BSYI|ATNI|MSGI|CDI) ERROR[0x0] SCSIBUSL[0xc0] LASTPHASE[0xa0]:(MSGI|CDI) SCSISEQ[0x12]:(ENAUTOATNP|ENRSELI) SBLKCTL[0xa]:(SELWIDE|SELBUSB) SCSIRATE[0x0] SEQCTL[0x10]:(FASTMODE) SEQ_FLAGS[0x40]:(NO_CDB_SENT) SSTAT0[0x2]:(SPIORDY) SSTAT1[0x1]:(REQINIT) SSTAT2[0x0] SSTAT3[0x0] SIMODE0[0x8]:(ENSWRAP) SIMODE1[0xac]:(ENSCSIPERR|ENBUSFREE|ENSCSIRST |ENSELTIMO) SXFRCTL0[0x88]:(SPIOEN|DFON) DFCNTRL[0x0] DFSTATUS[0x89]:(FIFOEMP|HDONE|PRELOAD_ AVAIL) STACK: 0xe2 0x0 0x164 0x179 SCB count = 8 Kernel NEXTQSCB = 7 Card NEXTQSCB = 7 QINFIFO entries: Waiting Queue entries: Disconnected Queue entries: QOUTFIFO entries: Sequencer Free SCB List: 2 0 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 2 2 23 24 25 26 27 28 29 30 31 Sequencer SCB Info: 0 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0xa7]:(TWIN_CHNLB) SCB_LUN[0x0] SCB_TAG[0xff] 1 SCB_CONTROL[0x60]:(TAG_ENB|DISCENB) SCB_SCSIID[0xb7]:(TWIN_CHNLB) SCB_LUN[0x0] SCB_TAG[0x2] 2 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0xb7]:(TWIN_CHNLB) SCB_LUN[0x0] SCB_TAG[0xff] 3 SCB_CONTROL[0xe0]:(TAG_ENB|DISCENB|TARGET_SCB) SCB_SCSIID[0xa7]:(TWIN_CHNLB) SCB_LUN[0x0] SCB_TAG[0xff] 4 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 5 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 6 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 7 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 8 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 9 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) SCB_LUN[0xff]:(SCB_XFERLEN_ODD|LID) SCB_TAG[0xff] 10 SCB_CONTROL[0x0] SCB_SCSIID[0xff]:(TWIN_CHNLB|OID|TWIN_TID) --More--(51%)