Am Samstag, den 10.09.2005, 16:59 +0200 schrieb Andreas Philipp: > Am Samstag, den 10.09.2005, 16:18 +0200 schrieb Christian Frommeyer: > > Am Samstag 10 September 2005 13:45 schrieb Andreas Philipp: > > > Das besagte Laufwerk (welches jetzt nicht mehr tut) haengt am 2.IDE > > > als Master, es taucht aber waehrend des gesamten boot-Vorgangs kein > > > "hdc" in den Meldungen mehr auf. > > > > Was sagt denn das BIOS? > > > > Gruß Chris > > Bios meldet das Laufwerk wie es sein soll. Es wird ja auch beim ersten > Installier-Boot-von-DVD benutzt. Unter suse (parallel-installation) > funzt es ohne Probleme (auch als Brenner). > > Gruesse, > Andreas
Mit hdc=ide-scsi in der grub kernelzeile geht es! Ich habe es mal beim Rechnerstart im grub-menu mit eingetragen und jetzt gibt es auch ein /dev/hdc. Nur komisch, dass das beim Installieren nicht eingetragen wurde, oder? Danke an Chris, Andreas > > P.S. die dmesg meiner etwas ergrauten Wuchtwumme ;), hab ich beim ersten > mail noch vergessen: > > Linux version 2.6.8-2-k7 ([EMAIL PROTECTED]) (gcc > version 3.3.5 (Debian 1:3.3.5-12)) #1 Thu May 19 18:03:29 JST 2005 > BIOS-provided physical RAM map: > BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) > BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) > BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) > BIOS-e820: 0000000000100000 - 000000000ffec000 (usable) > BIOS-e820: 000000000ffec000 - 000000000ffef000 (ACPI data) > BIOS-e820: 000000000ffef000 - 000000000ffff000 (reserved) > BIOS-e820: 000000000ffff000 - 0000000010000000 (ACPI NVS) > BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved) > 0MB HIGHMEM available. > 255MB LOWMEM available. > On node 0 totalpages: 65516 > DMA zone: 4096 pages, LIFO batch:1 > Normal zone: 61420 pages, LIFO batch:14 > HighMem zone: 0 pages, LIFO batch:1 > DMI 2.3 present. > ACPI disabled because your bios is from 2000 and too old > You can enable it with acpi=force > Built 1 zonelists > Kernel command line: root=/dev/hda1 ro > Local APIC disabled by BIOS -- reenabling. > Found and enabled local APIC! > Initializing CPU#0 > PID hash table entries: 1024 (order 10: 8192 bytes) > Detected 700.297 MHz processor. > Using tsc for high-res timesource > Console: colour VGA+ 80x25 > Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) > Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) > Memory: 251756k/262064k available (1536k kernel code, 9588k reserved, > 697k data, 148k init, 0k highmem) > Checking if this processor honours the WP bit even in supervisor mode... > Ok. > Calibrating delay loop... 1376.25 BogoMIPS > Security Scaffold v1.0.0 initialized > Mount-cache hash table entries: 512 (order: 0, 4096 bytes) > CPU: After generic identify, caps: 0183fbff c1c7fbff 00000000 00000000 > CPU: After vendor identify, caps: 0183fbff c1c7fbff 00000000 00000000 > CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) > CPU: L2 Cache: 256K (64 bytes/line) > CPU: After all inits, caps: 0183fbff c1c7fbff 00000000 00000020 > Intel machine check architecture supported. > Intel machine check reporting enabled on CPU#0. > CPU: AMD Athlon(tm) Processor stepping 02 > Enabling fast FPU save and restore... done. > Checking 'hlt' instruction... OK. > enabled ExtINT on CPU#0 > ESR value before enabling vector: 00000000 > ESR value after enabling vector: 00000000 > Using local APIC timer interrupts. > calibrating APIC timer ... > ..... CPU clock speed is 699.0903 MHz. > ..... host bus clock speed is 199.0972 MHz. > checking if image is initramfs...it isn't (ungzip failed); looks like an > initrd > Freeing initrd memory: 4496k freed > NET: Registered protocol family 16 > PCI: PCI BIOS revision 2.10 entry at 0xf1010, last bus=1 > PCI: Using configuration type 1 > mtrr: v2.0 (20020519) > ACPI: Subsystem revision 20040326 > ACPI: Interpreter disabled. > Linux Plug and Play Support v0.97 (c) Adam Belay > PnPBIOS: Scanning system for PnP BIOS support... > PnPBIOS: Found PnP BIOS installation structure at 0xc00fc2b0 > PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xc2e0, dseg 0xf0000 > pnp: 00:12: ioport range 0x290-0x297 has been reserved > pnp: 00:12: ioport range 0xe400-0xe47f has been reserved > pnp: 00:12: ioport range 0xe800-0xe83f has been reserved > PnPBIOS: 16 nodes reported by PnP BIOS; 16 recorded by driver > PCI: Probing PCI hardware > PCI: Probing PCI hardware (bus 00) > PCI: Using IRQ router VIA [1106/0686] at 0000:00:04.0 > spurious 8259A interrupt: IRQ7. > VFS: Disk quotas dquot_6.5.1 > Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) > devfs: 2004-01-31 Richard Gooch ([EMAIL PROTECTED]) > devfs: boot_options: 0x0 > Initializing Cryptographic API > PCI: Disabling Via external APIC routing > isapnp: Scanning for PnP cards... > isapnp: No Plug & Play device found > Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing > enabled > ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A > ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A > RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize > serio: i8042 AUX port at 0x60,0x64 irq 12 > serio: i8042 KBD port at 0x60,0x64 irq 1 > input: AT Translated Set 2 keyboard on isa0060/serio0 > NET: Registered protocol family 2 > IP: routing cache hash table of 2048 buckets, 16Kbytes > TCP: Hash tables configured (established 16384 bind 32768) > NET: Registered protocol family 8 > NET: Registered protocol family 20 > RAMDISK: cramfs filesystem found at block 0 > RAMDISK: Loading 4496 blocks [1 disk] into ram disk... done. > VFS: Mounted root (cramfs filesystem) readonly. > Freeing unused kernel memory: 148k freed > vesafb: probe of vesafb0 failed with error -6 > NET: Registered protocol family 1 > Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 > ide: Assuming 33MHz system bus speed for PIO modes; override with > idebus=xx > VP_IDE: IDE controller at PCI slot 0000:00:04.1 > VP_IDE: chipset revision 16 > VP_IDE: not 100% native mode: will probe irqs later > VP_IDE: VIA vt82c686a (rev 22) IDE UDMA66 controller on pci0000:00:04.1 > ide0: BM-DMA at 0xb800-0xb807, BIOS settings: hda:DMA, hdb:DMA > ide1: BM-DMA at 0xb808-0xb80f, BIOS settings: hdc:DMA, hdd:DMA > hda: ST380011A, ATA DISK drive > hdb: WDC WD800BB-00CAA1, ATA DISK drive > Using anticipatory io scheduler > ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 > hda: max request size: 1024KiB > hda: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=16383/255/63, > UDMA(66) > /dev/ide/host0/bus0/target0/lun0: p1 p3 > hdb: max request size: 128KiB > hdb: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=65535/16/63, > UDMA(66) > /dev/ide/host0/bus0/target1/lun0: p1 p2 p3 > hdd: IC35L060AVER07-0, ATA DISK drive > ide1 at 0x170-0x177,0x376 on irq 15 > hdd: max request size: 128KiB > hdd: 120103200 sectors (61492 MB) w/1916KiB Cache, CHS=65535/16/63, > UDMA(66) > /dev/ide/host0/bus1/target1/lun0: p1 p2 > kjournald starting. Commit interval 5 seconds > EXT3-fs: mounted filesystem with ordered data mode. > Adding 923728k swap on /dev/hdb2. Priority:-1 extents:1 > EXT3 FS on hda1, internal journal > input: ImPS/2 Generic Wheel Mouse on isa0060/serio1 > Capability LSM initialized > mice: PS/2 mouse device common for all mice > ts: Compaq touchscreen protocol output > Linux agpgart interface v0.100 (c) Dave Jones > parport_pc: VIA 686A/8231 detected > parport_pc: probing current configuration > parport_pc: Current parallel port base: 0x378 > parport0: PC-style at 0x378 (0x778), irq 7, using FIFO > [PCSPP,TRISTATE,COMPAT,ECP] > parport_pc: VIA parallel port: io=0x378, irq=7 > Linux Tulip driver version 1.1.13 (May 11, 2002) > PCI: Found IRQ 5 for device 0000:00:0d.0 > PCI: Sharing IRQ 5 with 0000:00:04.2 > PCI: Sharing IRQ 5 with 0000:00:04.3 > PCI: Sharing IRQ 5 with 0000:00:09.0 > tulip0: MII transceiver #1 config 1000 status 786d advertising 05e1. > eth0: ADMtek Comet rev 17 at 0x9000, 00:50:BF:A0:EF:35, IRQ 5. > es1371: version v0.32 time 18:08:26 May 19 2005 > PCI: Found IRQ 5 for device 0000:00:09.0 > PCI: Sharing IRQ 5 with 0000:00:04.2 > PCI: Sharing IRQ 5 with 0000:00:04.3 > PCI: Sharing IRQ 5 with 0000:00:0d.0 > es1371: found chip, vendor id 0x1274 device id 0x1371 revision 0x08 > es1371: found es1371 rev 8 at io 0x9400 irq 5 joystick 0x0 > ac97_codec: AC97 Audio codec, id: CRY19 (Cirrus Logic CS4297A rev A) > usbcore: registered new driver usbfs > usbcore: registered new driver hub > USB Universal Host Controller Interface driver v2.2 > PCI: Found IRQ 5 for device 0000:00:04.2 > PCI: Sharing IRQ 5 with 0000:00:04.3 > PCI: Sharing IRQ 5 with 0000:00:09.0 > PCI: Sharing IRQ 5 with 0000:00:0d.0 > uhci_hcd 0000:00:04.2: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 > Controller > uhci_hcd 0000:00:04.2: irq 5, io base 0000b400 > uhci_hcd 0000:00:04.2: new USB bus registered, assigned bus number 1 > hub 1-0:1.0: USB hub found > hub 1-0:1.0: 2 ports detected > PCI: Found IRQ 5 for device 0000:00:04.3 > PCI: Sharing IRQ 5 with 0000:00:04.2 > PCI: Sharing IRQ 5 with 0000:00:09.0 > PCI: Sharing IRQ 5 with 0000:00:0d.0 > uhci_hcd 0000:00:04.3: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 > Controller (#2) > uhci_hcd 0000:00:04.3: irq 5, io base 0000b000 > uhci_hcd 0000:00:04.3: new USB bus registered, assigned bus number 2 > hub 2-0:1.0: USB hub found > hub 2-0:1.0: 2 ports detected > agpgart: Detected VIA Apollo Pro 133 chipset > agpgart: Maximum main memory to use for agp memory: 203M > agpgart: AGP aperture is 64M @ 0xe4000000 > cpci_hotplug: CompactPCI Hot Plug Core version: 0.2 > pci_hotplug: PCI Hot Plug PCI Core version: 0.5 > pciehp: acpi_pciehprm:get_device PCI ROOT HID fail=0x1001 > shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x1001 > inserting floppy driver for 2.6.8-2-k7 > Floppy drive(s): fd0 is 1.44M > FDC 0 is a post-1991 82077 > Real Time Clock Driver v1.12 > input: PC Speaker > NET: Registered protocol family 17 > eth0: Setting full-duplex based on MII#1 link partner capability of > 45e1. > NET: Registered protocol family 10 > Disabled Privacy Extensions on device c02fc1a0(lo) > IPv6 over IPv4 tunneling driver > [drm] Initialized radeon 1.11.0 20020828 on minor 0: ATI Technologies > Inc Radeon RV250 If [Radeon 9000] > agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0. > agpgart: Putting AGP V2 device at 0000:00:00.0 into 1x mode > agpgart: Putting AGP V2 device at 0000:01:00.0 into 1x mode > [drm] Loading R200 Microcode > eth0: no IPv6 routers present > >