Sven Hartge wrote:
> Claus Malter <[EMAIL PROTECTED]> wrote:
>
>
>>Sep 28 17:33:37 distributor kernel: hdb: dma_intr: status=0x51 { DriveReady
>>SeekComplete Error }
>>Sep 28 17:33:38 distributor kernel: hdb: dma_intr: error=0x40 {
>>UncorrectableError }, LBAsect=61603928, sector=61603928
>
>
> Selbst wenn du meinst, das jetzt alles OK sei: eine Platte, die auch nur
> _einmal_ einen solchen Fehler lieferte, wird von mir dem Händler
> persönlich um die Ohren gehauen, alternativ via RMA an den Hersteller
> geschickt. Bisher hat sich noch niemand geweigert, mir die Platte zu
> tauschen (wenn noch Garantie bestand natürlich).Garantie besteht leider keine mehr. > > Was sagt "smartctl -a" zu der Platte? Poste bitte die _komplette_ > Ausgabe. Bei mittlerweile drei Festplatten hat smartctl Fehler gefunden. Beim Ausführen von smartctl habe ich auch wieder Fehlermeldungen im Syslog gefunden. Hier der gesamte Output von smartctl -a /dev/hdx, der mir leider nicht all zu viel sagt. Bin mal gespannt, was man daraus erkennen kann. ############ # /dev/hdb # ############ smartctl version 5.32 Copyright (C) 2002-4 Bruce Allen Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Device Model: Maxtor 6Y120L0 Serial Number: Y40MV53E Firmware Version: YAR41VW0 Device is: In smartctl database [for details use: -P show] ATA Version is: 7 ATA Standard is: ATA/ATAPI-7 T13 1532D revision 0 Local Time is: Sat Oct 1 09:05:08 2005 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 242) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. No General Purpose Logging support. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 63) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 3 Spin_Up_Time 0x0027 204 200 063 Pre-fail Always - 5514 4 Start_Stop_Count 0x0032 253 253 000 Old_age Always - 27 5 Reallocated_Sector_Ct 0x0033 252 246 063 Pre-fail Always - 13 6 Read_Channel_Margin 0x0001 253 253 100 Pre-fail Offline - 0 7 Seek_Error_Rate 0x000a 253 252 000 Old_age Always - 0 8 Seek_Time_Performance 0x0027 253 250 187 Pre-fail Always - 40918 9 Power_On_Minutes 0x0032 237 237 000 Old_age Always - 243h+30m 10 Spin_Retry_Count 0x002b 253 252 157 Pre-fail Always - 0 11 Calibration_Retry_Count 0x002b 253 252 223 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 253 253 000 Old_age Always - 151 192 Power-Off_Retract_Count 0x0032 253 253 000 Old_age Always - 0 193 Load_Cycle_Count 0x0032 253 253 000 Old_age Always - 0 194 Temperature_Celsius 0x0032 253 253 000 Old_age Always - 55 195 Hardware_ECC_Recovered 0x000a 253 252 000 Old_age Always - 11578 196 Reallocated_Event_Count 0x0008 253 253 000 Old_age Offline - 0 197 Current_Pending_Sector 0x0008 253 247 000 Old_age Offline - 0 198 Offline_Uncorrectable 0x0008 253 253 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x0008 199 196 000 Old_age Offline - 5 200 Multi_Zone_Error_Rate 0x000a 253 252 000 Old_age Always - 0 201 Soft_Read_Error_Rate 0x000a 253 245 000 Old_age Always - 0 202 TA_Increase_Count 0x000a 253 250 000 Old_age Always - 0 203 Run_Out_Cancel 0x000b 253 252 180 Pre-fail Always - 10 204 Shock_Count_Write_Opern 0x000a 253 252 000 Old_age Always - 0 205 Shock_Rate_Write_Opern 0x000a 253 252 000 Old_age Always - 0 207 Spin_High_Current 0x002a 253 252 000 Old_age Always - 0 208 Spin_Buzz 0x002a 253 252 000 Old_age Always - 0 209 Offline_Seek_Performnce 0x0024 196 192 000 Old_age Offline - 0 99 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0 100 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0 101 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0 SMART Error Log Version: 1 Warning: ATA error count 5327 inconsistent with error log pointer 5 ATA Error Count: 5327 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 5327 occurred at disk power-on lifetime: 5335 hours (222 days + 7 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 08 97 00 00 f0 Error: UNC 8 sectors at LBA = 0x00000097 = 151 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 08 97 00 00 f0 08 5d+03:31:00.896 READ DMA ca 00 00 4f 0c 84 fd 08 5d+03:31:00.752 WRITE DMA ca 00 00 4f 0b 84 fd 08 5d+03:31:00.752 WRITE DMA ca 00 00 4f 0a 84 fd 08 5d+03:31:00.752 WRITE DMA ca 00 00 4f 09 84 fd 08 5d+03:31:00.736 WRITE DMA Error 5326 occurred at disk power-on lifetime: 5291 hours (220 days + 11 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 06 90 05 2c f3 Error: UNC 6 sectors at LBA = 0x032c0590 = 53216656 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 08 90 05 2c f3 08 3d+01:15:42.464 READ DMA c8 00 08 88 05 2c f3 08 3d+01:15:41.264 READ DMA c8 00 08 80 05 2c f3 08 3d+01:15:40.096 READ DMA c8 00 08 78 05 2c f3 08 3d+01:15:38.928 READ DMA c8 00 08 70 05 2c f3 08 3d+01:15:37.760 READ DMA Error 5325 occurred at disk power-on lifetime: 5291 hours (220 days + 11 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 07 88 05 2c f3 Error: UNC 7 sectors at LBA = 0x032c0588 = 53216648 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 08 88 05 2c f3 08 3d+01:15:41.264 READ DMA c8 00 08 80 05 2c f3 08 3d+01:15:40.096 READ DMA c8 00 08 78 05 2c f3 08 3d+01:15:38.928 READ DMA c8 00 08 70 05 2c f3 08 3d+01:15:37.760 READ DMA c8 00 08 68 05 2c f3 08 3d+01:15:36.576 READ DMA Error 5324 occurred at disk power-on lifetime: 5291 hours (220 days + 11 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 08 80 05 2c f3 Error: UNC 8 sectors at LBA = 0x032c0580 = 53216640 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 08 80 05 2c f3 08 3d+01:15:40.096 READ DMA c8 00 08 78 05 2c f3 08 3d+01:15:38.928 READ DMA c8 00 08 70 05 2c f3 08 3d+01:15:37.760 READ DMA c8 00 08 68 05 2c f3 08 3d+01:15:36.576 READ DMA c8 00 08 60 05 2c f3 08 3d+01:15:35.344 READ DMA Error 5323 occurred at disk power-on lifetime: 5291 hours (220 days + 11 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 08 78 05 2c f3 Error: UNC 8 sectors at LBA = 0x032c0578 = 53216632 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 08 78 05 2c f3 08 3d+01:15:38.928 READ DMA c8 00 08 70 05 2c f3 08 3d+01:15:37.760 READ DMA c8 00 08 68 05 2c f3 08 3d+01:15:36.576 READ DMA c8 00 08 60 05 2c f3 08 3d+01:15:35.344 READ DMA c8 00 08 58 05 2c f3 08 3d+01:15:33.904 READ DMA SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. ############ # /dev/hdf # ############ smartctl version 5.32 Copyright (C) 2002-4 Bruce Allen Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Device Model: Maxtor 4W060H4 Serial Number: W406RJXC Firmware Version: AAH41310 Device is: In smartctl database [for details use: -P show] ATA Version is: 6 ATA Standard is: ATA/ATAPI-6 T13 1410D revision 0 Local Time is: Sat Oct 1 09:03:16 2005 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 30) seconds. Offline data collection capabilities: (0x1b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. No General Purpose Logging support. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 47) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000a 252 252 000 Old_age Always - 0 3 Spin_Up_Time 0x0027 252 252 063 Pre-fail Always - 386 4 Start_Stop_Count 0x0032 253 253 000 Old_age Always - 3 5 Reallocated_Sector_Ct 0x0033 252 252 063 Pre-fail Always - 4 6 Read_Channel_Margin 0x0001 253 253 100 Pre-fail Offline - 0 7 Seek_Error_Rate 0x000a 252 252 000 Old_age Always - 0 8 Seek_Time_Performance 0x0027 249 248 187 Pre-fail Always - 3196 9 Power_On_Minutes 0x0032 246 246 000 Old_age Always - 296h+56m 10 Spin_Retry_Count 0x002b 252 252 223 Pre-fail Always - 0 11 Calibration_Retry_Count 0x002b 252 252 223 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 253 253 000 Old_age Always - 275 196 Reallocated_Event_Count 0x0008 253 253 000 Old_age Offline - 0 197 Current_Pending_Sector 0x0008 253 253 000 Old_age Offline - 0 198 Offline_Uncorrectable 0x0008 253 253 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x0008 253 253 000 Old_age Offline - 0 200 Multi_Zone_Error_Rate 0x000a 252 252 000 Old_age Always - 0 201 Soft_Read_Error_Rate 0x000a 252 252 000 Old_age Always - 2 202 TA_Increase_Count 0x000a 252 252 000 Old_age Always - 0 203 Run_Out_Cancel 0x000b 252 252 180 Pre-fail Always - 0 204 Shock_Count_Write_Opern 0x000a 252 252 000 Old_age Always - 0 205 Shock_Rate_Write_Opern 0x000a 252 252 000 Old_age Always - 0 207 Spin_High_Current 0x002a 252 252 000 Old_age Always - 0 208 Spin_Buzz 0x002a 252 252 000 Old_age Always - 0 209 Offline_Seek_Performnce 0x0024 253 253 000 Old_age Offline - 0 96 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0 97 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0 98 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0 99 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0 100 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0 101 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0 SMART Error Log Version: 1 Warning: ATA error count 247 inconsistent with error log pointer 5 ATA Error Count: 247 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 247 occurred at disk power-on lifetime: 2326 hours (96 days + 22 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 00 0b 4f c2 f0 Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- b0 da 00 00 4f c2 f0 08 5d+13:27:31.840 SMART RETURN STATUS ec 00 00 77 c1 49 f0 08 5d+13:27:31.824 IDENTIFY DEVICE c8 00 08 87 01 04 f2 08 5d+10:38:11.376 READ DMA c8 00 08 8f b4 6e f2 08 5d+10:38:11.376 READ DMA c8 00 08 27 ef 6b f2 08 5d+10:38:11.376 READ DMA Error 246 occurred at disk power-on lifetime: 2316 hours (96 days + 12 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 08 77 00 58 f2 Error: UNC 8 sectors at LBA = 0x02580077 = 39321719 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 08 77 00 58 f2 08 4d+21:39:20.512 READ DMA c8 00 08 77 00 10 f7 08 4d+21:39:20.496 READ DMA c8 00 38 07 4e ab f4 08 4d+21:40:12.800 READ DMA c8 00 60 9f 4d ab f4 08 4d+21:40:12.800 READ DMA c8 00 80 1f 4d ab f4 08 4d+21:40:12.800 READ DMA Error 245 occurred at disk power-on lifetime: 2316 hours (96 days + 12 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 08 77 00 38 f4 Error: UNC 8 sectors at LBA = 0x04380077 = 70778999 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 08 77 00 38 f4 08 4d+21:38:26.272 READ DMA c8 00 08 7f 10 28 f4 08 4d+21:38:26.272 READ DMA c8 00 78 bf 77 0b f7 08 4d+21:38:26.224 READ DMA c8 00 80 3f 77 0b f7 08 4d+21:38:26.224 READ DMA c8 00 80 bf 76 0b f7 08 4d+21:38:26.208 READ DMA Error 244 occurred at disk power-on lifetime: 2316 hours (96 days + 12 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 08 77 00 38 f4 Error: UNC 8 sectors at LBA = 0x04380077 = 70778999 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 08 77 00 38 f4 08 4d+21:25:08.736 READ DMA c8 00 08 77 10 30 f4 08 4d+21:25:08.720 READ DMA c8 00 08 77 00 30 f4 08 4d+21:25:08.720 READ DMA c8 00 08 97 10 20 f4 08 4d+21:25:08.656 READ DMA c8 00 38 57 29 22 f1 08 4d+21:25:08.624 READ DMA Error 243 occurred at disk power-on lifetime: 2316 hours (96 days + 12 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 08 77 00 58 f2 Error: UNC 8 sectors at LBA = 0x02580077 = 39321719 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 08 77 00 58 f2 08 4d+21:20:53.712 READ DMA c8 00 08 77 10 50 f2 08 4d+21:20:53.696 READ DMA c8 00 08 77 00 50 f2 08 4d+21:20:53.680 READ DMA c8 00 08 8f 10 40 f2 08 4d+21:20:53.664 READ DMA c8 00 30 8f a1 de f0 08 4d+21:20:53.648 READ DMA SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] Device does not support Selective Self Tests/Logging ############ # /dev/hdf # ############ smartctl version 5.32 Copyright (C) 2002-4 Bruce Allen Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Device Model: Maxtor 32049U3 Serial Number: N3H3NVNC Firmware Version: BAC51KJ0 Device is: In smartctl database [for details use: -P show] ATA Version is: 6 ATA Standard is: ATA/ATAPI-6 T13 1410D revision 0 Local Time is: Sat Oct 1 09:05:51 2005 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x1b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. No General Purpose Logging support. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 19) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000a 253 252 000 Old_age Always - 340651 3 Spin_Up_Time 0x0027 252 252 063 Pre-fail Always - 2 4 Start_Stop_Count 0x0032 253 253 000 Old_age Always - 2 5 Reallocated_Sector_Ct 0x0033 253 253 063 Pre-fail Always - 0 6 Read_Channel_Margin 0x0001 253 253 100 Pre-fail Offline - 0 7 Seek_Error_Rate 0x000a 253 252 000 Old_age Always - 66061 8 Seek_Time_Performance 0x0027 251 251 187 Pre-fail Always - 142992346561567 9 Power_On_Minutes 0x0032 227 227 000 Old_age Always - 9171h+27m 10 Spin_Retry_Count 0x002b 252 252 223 Pre-fail Always - 2 11 Calibration_Retry_Count 0x002b 252 252 223 Pre-fail Always - 4 12 Power_Cycle_Count 0x0032 251 251 000 Old_age Always - 848 196 Reallocated_Event_Count 0x0008 253 253 000 Old_age Offline - 0 197 Current_Pending_Sector 0x0008 253 253 000 Old_age Offline - 0 198 Offline_Uncorrectable 0x0008 253 253 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x0008 199 199 000 Old_age Offline - 17157 200 Multi_Zone_Error_Rate 0x000a 253 252 000 Old_age Always - 273430 201 Soft_Read_Error_Rate 0x000a 253 252 000 Old_age Always - 34360079019 202 TA_Increase_Count 0x000a 253 252 000 Old_age Always - 340651 203 Run_Out_Cancel 0x000b 253 252 180 Pre-fail Always - 340651 204 Shock_Count_Write_Opern 0x000a 253 252 000 Old_age Always - 340651 205 Shock_Rate_Write_Opern 0x000a 253 252 000 Old_age Always - 340651 207 Spin_High_Current 0x002a 252 252 000 Old_age Always - 2 208 Spin_Buzz 0x002a 252 252 000 Old_age Always - 2 209 Offline_Seek_Performnce 0x0024 253 253 000 Old_age Offline - 0 96 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0 97 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0 98 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0 99 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0 100 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0 101 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0 SMART Error Log Version: 1 Warning: ATA error count 2108 inconsistent with error log pointer 5 ATA Error Count: 2108 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 2108 occurred at disk power-on lifetime: 2304 hours (96 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 00 0b 4f c2 f0 Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- b0 da 00 01 4f c2 f0 08 5d+13:43:37.168 SMART RETURN STATUS ec 00 00 39 29 ce f0 08 5d+13:43:37.152 IDENTIFY DEVICE c8 00 08 31 29 ce f0 08 5d+10:49:06.544 READ DMA c8 00 08 c9 7f c1 f1 08 5d+10:49:06.544 READ DMA c8 00 08 c1 7f c1 f1 08 5d+10:49:06.528 READ DMA Error 2107 occurred at disk power-on lifetime: 8530 hours (355 days + 10 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 05 01 00 00 b0 Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- a1 00 05 01 00 00 b0 08 00:08:45.216 IDENTIFY PACKET DEVICE Error 2106 occurred at disk power-on lifetime: 2237 hours (93 days + 5 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 05 01 00 00 b0 Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- a1 00 05 01 00 00 b0 00 00:04:32.400 IDENTIFY PACKET DEVICE Error 2105 occurred at disk power-on lifetime: 8530 hours (355 days + 10 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 05 01 00 00 b0 Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- a1 00 05 01 00 00 b0 08 00:08:32.816 IDENTIFY PACKET DEVICE c8 00 04 01 00 00 f0 08 00:04:54.640 READ DMA c8 00 02 01 9f 62 f2 08 00:04:54.608 READ DMA c8 00 08 00 00 00 f0 08 00:04:54.352 READ DMA c8 00 08 00 ae 62 f2 08 00:04:54.336 READ DMA Error 2104 occurred at disk power-on lifetime: 2237 hours (93 days + 5 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 05 01 00 00 b0 Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- a1 00 05 01 00 00 b0 00 00:04:32.400 IDENTIFY PACKET DEVICE SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] Device does not support Selective Self Tests/Logging > S° > Claus -- Haeufig gestellte Fragen und Antworten (FAQ): http://www.de.debian.org/debian-user-german-FAQ/ Zum AUSTRAGEN schicken Sie eine Mail an [EMAIL PROTECTED] mit dem Subject "unsubscribe". Probleme? Mail an [EMAIL PROTECTED] (engl)
