Da mit diesem Brenner, warum auch immer, nur cdrdao RWs brauchbar löscht und
dies jahrelang, aber sehr selten verwendet, funktioniert, hat, habe ich zur
Zeit ein Syntax-Problem, bei dem ich anstehe. Wie spreche ich den Brenner mit
"IDs" an und nicht mit hdx?
uname -r
2.6.15-1-686
/usr/local/bin/cdrecord-prodvd -s -scanbus dev=ATA
Cdrecord-ProDVD-Clone 2.01b31 (i686-pc-linux-gnu) Copyright (C) 1995-2004 J�g
Schilling
Unlocked features:
Limited features:
scsidev: 'ATA'
devname: 'ATA'
scsibus: -2 target: -2 lun: -2
Warning: Using badly designed ATAPI via /dev/hd* interface.
Linux sg driver version: 3.5.27
Using libscg version 'schily-0.8'.
...
scsibus1:
1,0,0 100) 'ATAPI ' 'CD-RW 48XMax ' '180D' Removable CD-ROM
1,1,0 101) *
1,2,0 102) *
1,3,0 103) *
1,4,0 104) *
1,5,0 105) *
1,6,0 106) *
1,7,0 107) *
/usr/bin/cdrdao blank --device ATA:1,0,0 --driver generic-mmc --blank-mode
full
Cdrdao version 1.1.9 - (C) Andreas Mueller <[EMAIL PROTECTED]>
SCSI interface library - (C) Joerg Schilling
Paranoia DAE library - (C) Monty
Check http://cdrdao.sourceforge.net/drives.html#dt for current driver tables.
ERROR: Cannot open SCSI device 'ATA:1,0,0': Cannot open '/dev/hda'
Supported SCSI transports for this platform:
Transport name: sg
Transport descr.: Generic transport independent SCSI
Transp. layer ind.:
Target specifier: bus,target,lun
Target example: 1,2,0
SCSI Bus scanning: supported
Open via UNIX device: not supported
Transport name: pg
Transport descr.: SCSI transport for ATAPI over Parallel Port
Transp. layer ind.:
Target specifier: bus,target,lun
Target example: 1,2,0
SCSI Bus scanning: supported
Open via UNIX device: not supported
Transport name: ATA
Transport descr.: ATA Packet specific SCSI transport
Transp. layer ind.: ATAPI:
Target specifier: bus,target,lun
Target example: ATAPI:1,2,0
SCSI Bus scanning: supported
Open via UNIX device: not supported
Transport name: ATA
Transport descr.: ATA Packet specific SCSI transport using sg interface
Transp. layer ind.: ATA:
Target specifier: bus,target,lun
Target example: 1,2,0
SCSI Bus scanning: supported
Open via UNIX device: not supported
ERROR: Please use option '--device [proto:]bus,id,lun', e.g. --device 0,6,0 or
--device ATAPI:0,0,0
ERROR: Cannot setup device ATA:1,0,0.
/usr/bin/cdrdao blank --device ATAPI:1,0,0 --driver generic-mmc --blank-mode
full
Cdrdao version 1.1.9 - (C) Andreas Mueller <[EMAIL PROTECTED]>
SCSI interface library - (C) Joerg Schilling
Paranoia DAE library - (C) Monty
Check http://cdrdao.sourceforge.net/drives.html#dt for current driver tables.
Using libscg version 'schily-0.8'
ATAPI:1,0,0: ATAPI CD-RW 48XMax Rev: 180D
Using driver: Generic SCSI-3/MMC - Version 2.0 (options 0x0000)
Blanking disk...
ERROR: Cannot erase CD-RW.
ERROR: Blanking failed.
/usr/bin/cdrdao blank --device /dev/hdc --driver generic-mmc --blank-mode full
Cdrdao version 1.1.9 - (C) Andreas Mueller <[EMAIL PROTECTED]>
SCSI interface library - (C) Joerg Schilling
Paranoia DAE library - (C) Monty
Check http://cdrdao.sourceforge.net/drives.html#dt for current driver tables.
Using libscg version 'schily-0.8'
/dev/hdc: ATAPI CD-RW 48XMax Rev: 180D
Using driver: Generic SCSI-3/MMC - Version 2.0 (options 0x0000)
Blanking disk...
Blanking time: 434 seconds
Al
