Mein Mailserver hatte 'nen Plattencrash; weiss nicht ob diese email versendet wurde ...
"A.C. Almeida" schrieb: > > Hi, > > OK, OK, habe ich wohl auch etwas mißverstanden ... > > Hier nun die Outputs: > > Bootvorgang, und siehe: da ist die karte > schnipp > ... > ne.c:v1.10 9/23/94 Donald Becker ([EMAIL PROTECTED]) > Last modified Nov 1, 2000 by Paul Gortmaker > NE*000 ethercard probe at 0x260: 52 54 40 28 e0 ac > eth0: NE2000 found at 0x260, using IRQ 4. > ... > NET4: Linux TCP/IP 1.0 for NET4.0 > IP Protocols: ICMP, UDP, TCP, IGMP > IP: routing cache hash table of 512 buckets, 4Kbytes > TCP: Hash tables configured (established 8192 bind 8192) > NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. > ... > schnipp > > ifconfig > > eth0 Link encap:Ethernet HWaddr 52:54:40:28:E0:AC > inet addr:192.168.1.5 Bcast:192.168.1.255 Mask:255.255.255.0 > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > RX packets:0 errors:0 dropped:0 overruns:0 frame:0 > TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:100 > RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) > Interrupt:4 Base address:0x260 > > lo Link encap:Local Loopback > inet addr:127.0.0.1 Mask:255.0.0.0 > UP LOOPBACK RUNNING MTU:16436 Metric:1 > RX packets:4 errors:0 dropped:0 overruns:0 frame:0 > TX packets:4 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:0 > RX bytes:518 (518.0 b) TX bytes:518 (518.0 b) > route> > Kernel IP routing table > Destination Gateway Genmask Flags Metric Ref Use Iface > localnet * 255.255.255.0 U 0 0 0 eth0 > default router 0.0.0.0 UG 0 0 0 eth0 > > und die config-Datei > # /etc/network/interfaces -- configuration file for ifup(8), ifdown(8) > # The loopback interface > auto lo > iface lo inet loopback > # > auto eth0 > iface eth0 inet static > address 192.168.1.5 > netmask 255.255.255.0 > network 192.168.1.0 > broadcast 192.168.1.255 > gateway 192.168.1.1 > > Also: Rechneradresse ist die 192.168.1.5; der Router hat die 192.168.1.1, soweit >alles > i.O. > > Ping liefert "time out"; modprobe -r eth0 liefert keine Fehlermeldung; ISA-Karte ist > IRQ=4 und IO=0x260 > > Tja und nun weiss ich nicht weiter ... :(( Das schlaue Linux-Buch von Marco Budde >hilft > mir auch nicht weiter. > > Gruß > > Antonio > > > > > Ach, ich glaube, hier wurde meine Frage falsch verstanden: Ich meinte, > > warum muss ich das Modul neu laden, damit ich die Netzwerkkarte nutzen > > kann, nicht warum ich die Frage beantworten muss... > > > > Gruß > > Holger > > > > -- > > Zum AUSTRAGEN schicken Sie eine Mail an [EMAIL PROTECTED] > > mit dem Subject "unsubscribe". Probleme? Mail an [EMAIL PROTECTED] (engl) -- Zum AUSTRAGEN schicken Sie eine Mail an [EMAIL PROTECTED] mit dem Subject "unsubscribe". Probleme? Mail an [EMAIL PROTECTED] (engl)