Hallo zusammen, ich habe mir ein RAIDI aufgesetzt. Allerdings habe ich jetzt das Problem, das der Rechner nur bootet, wenn beide Platten angeschlossen sind. Nehme ich eine der beiden Platten heraus fährt der Rechner nicht mehr richtig hoch, es füllt sich der Bildschirm nur noch mit "01"
Die howtows sowie http://www.dejanews.com brachten mich bis jetzt leider nicht auf den richtigen Weg, vielleicht hat hier jemand eine Idee? Danke schon mal im Voraus Patrick hier meine Plattenaufteilung: Disk /dev/sda: 255 heads, 63 sectors, 1106 cylinders Units = sectors of 1 * 512 bytes Device Boot Start End Blocks Id System /dev/sda1 * 63 48194 24066 fd Linux raid autodetect /dev/sda2 48195 1044224 498015 82 Linux swap /dev/sda3 1044225 13831964 6393870 5 Extended /dev/sda4 13831965 17767889 1967962+ fd Linux raid autodetect /dev/sda5 1044288 5960114 2457913+ fd Linux raid autodetect /dev/sda6 5960178 9896039 1967931 fd Linux raid autodetect /dev/sda7 9896103 13831964 1967931 fd Linux raid autodetect Disk /dev/sdb: 255 heads, 63 sectors, 1115 cylinders Units = sectors of 1 * 512 bytes Device Boot Start End Blocks Id System /dev/sdb1 * 63 48194 24066 fd Linux raid autodetect /dev/sdb2 48195 1028159 489982+ 82 Linux swap /dev/sdb3 1028160 13751639 6361740 5 Extended /dev/sdb4 13751640 17671499 1959930 fd Linux raid autodetect /dev/sdb5 1028223 5911919 2441848+ fd Linux raid autodetect /dev/sdb6 5911983 9831779 1959898+ fd Linux raid autodetect /dev/sdb7 9831843 13751639 1959898+ fd Linux raid autodetect chewbakka:/home/patrick# cat /proc/mdstat Personalities : [linear] [raid1] [multipath] read_ahead 1024 sectors md1 : active raid1 sdb1[0] sda1[1] 24000 blocks [2/2] [UU] md2 : active raid1 sdb5[0] sda5[1] 2441728 blocks [2/2] [UU] md3 : active raid1 sdb6[0] sda6[1] 1959808 blocks [2/2] [UU] md4 : active raid1 sdb7[0] sda7[1] 1959808 blocks [2/2] [UU] md0 : active raid1 sdb4[0] sda4[1] 1959808 blocks [2/2] [UU] unused devices: <none> lilo.conf (wurde mit "lilo -C /etc/lilo.conf" in den MBR von SDA geschrieben : # Support LBA for large hard disks. lba32 # Overrides the default mapping between harddisk names and the BIOS' # harddisk order. Use with caution. disk=/dev/md0 bios=0x80 partition=/dev/md1 boot=/dev/sda root=/dev/md0 install=/boot/boot-menu.b map=/boot/map delay=20 # single-key # delay=100 timeout=100 vga=normal default=Linux image=/vmlinuz label=Linux read-only # restricted # alias=1 image=/vmlinuz.old label=LinuxOLD read-only optional # restricted # alias=2 lilo.conf.sdb (wurde mit "lilo -C /etc/lilo.conf.sdb" in den MBR von SDB geschrieben: # Support LBA for large hard disks. lba32 # Overrides the default mapping between harddisk names and the BIOS' # harddisk order. Use with caution. disk=/dev/md0 bios=0x80 partition=/dev/md1 boot=/dev/sdb root=/dev/md0 install=/boot/boot-menu.b map=/boot/map delay=20 # single-key # delay=100 timeout=100 vga=normal default=Linux image=/vmlinuz label=Linux read-only # restricted # alias=1 image=/vmlinuz.old label=LinuxOLD read-only optional # restricted # alias=2 -- Häufig gestellte Fragen und Antworten (FAQ): http://www.de.debian.org/debian-user-german-FAQ/ Zum AUSTRAGEN schicken Sie eine Mail an [EMAIL PROTECTED] mit dem Subject "unsubscribe". Probleme? Mail an [EMAIL PROTECTED] (engl)