Hallo Leute,
habe einen Promise Raid Controller PDC20276 (mit dem Bios vom TX2000) auf mein Mainboard (Gigabyte 845PE Ultra). Ich glaube, dass Knoppix diesen Controller erkannt hat. Hier ein Auszug von "dmsg":
PCI: Device 00:1f.1 not available because of resource collisions ICH4: BIOS setup was incomplete. ICH4: chipset revision 2 ICH4: not 100% native mode: will probe irqs later ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:pio HPT370: IDE controller on PCI bus 02 dev 10 HPT370: chipset revision 3 HPT370: not 100% native mode: will probe irqs later HPT370: using 33MHz PCI clock ide2: BM-DMA at 0xb000-0xb007, BIOS settings: hde:pio, hdf:pio ide3: BM-DMA at 0xb008-0xb00f, BIOS settings: hdg:pio, hdh:pio PDC20276: IDE controller on PCI bus 02 dev 60 PDC20276: chipset revision 1 PDC20276: not 100% native mode: will probe irqs later PDC20276: (U)DMA Burst Bit ENABLED Primary MASTER Mode Secondary MASTER Mode. ide4: BM-DMA at 0xc800-0xc807, BIOS settings: hdi:pio, hdj:pio ide5: BM-DMA at 0xc808-0xc80f, BIOS settings: hdk:pio, hdl:pio hda: IBM-DTTA-351680, ATA DISK drive hdb: IBM-DHEA-36481, ATA DISK drive hdc: PLEXTOR CD-R PX-W2410A, ATAPI CD/DVD-ROM drive hde: FUJITSU MPF3204AT FF, ATA DISK drive hdg: FUJITSU MPF3204AT FF, ATA DISK drive hdi: Maxtor 6Y080L0, ATA DISK drive hdk: Maxtor 6Y080L0, ATA DISK drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 ide1 at 0x170-0x177,0x376 on irq 15 ide2 at 0xa000-0xa007,0xa402 on irq 22 ide3 at 0xa800-0xa807,0xac02 on irq 22 ide4 at 0xb800-0xb807,0xbc02 on irq 18 ide5 at 0xc000-0xc007,0xc402 on irq 18
....
....
....
Partition check: hda: hda1 hdb: hdb1 hdb2 hde: [PTBL] [2491/255/63] hde1 hdg: [PTBL] [2491/255/63] hdg1 hdi: [PTBL] [9964/255/63] hdi1 hdi2 hdi3 < > hdk: unknown partition table Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 RAMDISK driver initialized: 16 RAM disks of 100000K size 1024 blocksize Cronyx Ltd, Synchronous PPP and CISCO HDLC (c) 1994 Linux port (c) 1998 Building Number Three Ltd & Jan "Yenya" Kasprzak. ataraid/d0: ataraid/d0p1 ataraid/d0p2 ataraid/d0p3 < ataraid/d0p5 ataraid/d0p6 ataraid/d0p7 ataraid/d0p8 > Drive 0 is 78167 Mb (56 / 0) Drive 1 is 78167 Mb (57 / 0) Raid0 array consists of 2 drives. Promise Fasttrak(tm) Softwareraid driver for linux version 0.03beta Highpoint HPT370 Softwareraid driver for linux version 0.01
....
....
....
Knoppix erkennt sogar das bereits bestehende Raid-Array (0). So weit glaube ich, ist alles ok. Nur, wie kann ich dieses Raid-Array mounten? In /dev habe ich alle Festplatten von hda bis hdg. Diese Platten kann ich auch alle ansprechen. Auch der Highpoint HPT370 Raid-Controller funktioniert mit und ohne Raid-Array einwandfrei. Nur die zwei Platten an dem Promise-Controller fehlen.
Wo ist das Raid-Array?
Bitte um Hilfe. Schonmal vielen Dank im Vorraus!!
Mit freundlichen Grüßen
Ciao John |