Wiem, ze to juz nudne, ale problem jest powazny, bo przez niego stoje w
miejscu. Powoli zaczyna mnie szlag trafiac, bo kombinowalem juz na
wszystkie strony, ostatnio probowalem tez make-kpkg. I co? I za kazdym
razem to samo - z nowym jadrem system nie laduje sie z kontrolera
HPT370. Jedyna rzecz, ktora nie daje mi spokoju, ale rowniez trzyma mnie
przy nadzei :-) to fakt, ze jadro z czasow instalacji Debiana z plytki
dziala. Przy ostatniej kompilacji juz sie zajaralem, bo poszlo MTRR,
rivafb i grafika juz przy starcie wygladala lepiej, ale znowu wylozyl
sie w standardowym miejscu. Moge Wam przeslac dowolna ilosc logow,
plikow konfiguracyjnych itd., ale blagam pomozcie, bo powoli przestaje
mi sie Debian podobac, a to bardzo zle objawy... :-( Ewentualnie ja
jeszcze widze takie mozliwosci:
1. ktos mi mowil zeby hpt370 zrobic jako modul, ale to chyba bzdura, bo
niby jak system wystartuje?
2. mozliwe, ze to niekoniecznie jadro - moze cos w lilo.conf?
wkompilowalem rowniez "boot off board devices" czy cos takiego
3. albo moze ktos wie jakie jeszcze rzeczy koniecznie trzeba wkompilowac?
Normalnie mowie Wam - konia z rzedem temu kto pomoze mi zrobic system na
nowym jadrze!
P.S. Na poczatek dorzucam lilo.conf. Co jeszcze powinienem?
--
http://www.miki.z.pl
[EMAIL PROTECTED]
Gadu-gadu: 2128279
Mobile: +48607345846
# /etc/lilo.conf - See: `lilo(8)' and `lilo.conf(5)',
# --------------- `install-mbr(8)', `/usr/share/doc/lilo/',
# and `/usr/share/doc/mbr/'.
# +---------------------------------------------------------------+
# | !! Reminder !! |
# | |
# | Don't forget to run `lilo' after you make changes to this |
# | conffile, `/boot/bootmess.txt', or install a new kernel. The |
# | computer will most likely fail to boot if a kernel-image |
# | post-install script or you don't remember to run `lilo'. |
# | |
# +---------------------------------------------------------------+
# Support LBA for large hard disks.
#
lba32
# Overrides the default mapping between harddisk names and the BIOS'
# harddisk order. Use with caution.
disk=/dev/hde
bios=0x80
# Specifies the boot device. This is where Lilo installs its boot
# block. It can be either a partition, or the raw device, in which
# case it installs in the MBR, and will overwrite the current MBR.
#
boot=/dev/hde
# Specifies the device that should be mounted as root. (`/')
#
root=/dev/hde1
# Enable map compaction:
# Tries to merge read requests for adjacent sectors into a single
# read request. This drastically reduces load time and keeps the
# map smaller. Using `compact' is especially recommended when
# booting from a floppy disk. It is disabled here by default
# because it doesn't always work.
#
# compact
# Installs the specified file as the new boot sector
# You have the choice between: bmp, compat, menu and text
# Look in /boot/ and in lilo.conf(5) manpage for details
#
install=/boot/boot-menu.b
# Specifies the location of the map file
#
map=/boot/map
# You can set a password here, and uncomment the `restricted' lines
# in the image definitions below to make it so that a password must
# be typed to boot anything but a default configuration. If a
# command line is given, other than one specified by an `append'
# statement in `lilo.conf', the password will be required, but a
# standard default boot will not require one.
#
# This will, for instance, prevent anyone with access to the
# console from booting with something like `Linux init=/bin/sh',
# and thus becoming `root' without proper authorization.
#
# Note that if you really need this type of security, you will
# likely also want to use `install-mbr' to reconfigure the MBR
# program, as well as set up your BIOS to disallow booting from
# removable disk or CD-ROM, then put a password on getting into the
# BIOS configuration as well. Please RTFM `install-mbr(8)'.
#
password=xxx
# Specifies the number of deciseconds (0.1 seconds) LILO should
# wait before booting the first image.
#
delay=1
# You can put a customized boot message up if you like. If you use
# `prompt', and this computer may need to reboot unattended, you
# must specify a `timeout', or it will sit there forever waiting
# for a keypress. `single-key' goes with the `alias' lines in the
# `image' configurations below. eg: You can press `1' to boot
# `Linux', `2' to boot `LinuxOLD', if you uncomment the `alias'.
#
# message=/boot/bootmess.txt
# prompt
# single-key
# delay=100
# timeout=100
# Specifies the VGA text mode at boot time. (normal, extended, ask, <mode>)
#
# vga=ask
# vga=9
#
vga=normal
# Kernel command line options that apply to all installed images go
# here. See: The `boot-prompt-HOWO' and `kernel-parameters.txt' in
# the Linux kernel `Documentation' directory.
#
append="hda=ide-scsi"
# Boot up Linux by default.
#
default=Linux
image=/vmlinuz
label=Linux
read-only
restricted
# alias=1
# If you have another OS on this machine to boot, you can uncomment the
# following lines, changing the device name on the `other' line to
# where your other OS' partition is.
#
# other=/dev/hda4
# label=HURD
# restricted
# alias=3