Galera,
alguém tem uma idéia de como mapear/mountar automaticamente um memory
key, assim como desmontar?
A minha estação pessoal está com sarge instalado, e com o kernel 2.6.8.
Tenho também o udev e o hald instalado. Quando espeto o memory key,
aparecem as seguintes mensagens no /var/log/syslog:
-----------------------
May 8 22:31:34 localhost kernel: Initializing USB Mass Storage
driver...
May 8 22:31:34 localhost kernel: scsi0 : SCSI emulation for USB Mass
Storage devices
May 8 22:31:34 localhost kernel: Vendor: SanDisk Model: Cruzer
Mini Rev: 0.1
May 8 22:31:34 localhost kernel: Type: Direct-Access
ANSI SCSI revision: 02
May 8 22:31:34 localhost kernel: SCSI device sda: 250879 512-byte hdwr
sectors (128 MB)
May 8 22:31:34 localhost kernel: sda: assuming Write Enabled
May 8 22:31:34 localhost kernel: sda: assuming drive cache: write
through
May 8 22:31:34 localhost kernel: /dev/scsi/host0/bus0/target0/lun0: p1
May 8 22:31:34 localhost kernel: Attached scsi removable disk sda at
scsi0, channel 0, id 0, lun 0
May 8 22:31:34 localhost usb.agent[20640]: usb-storage: loaded
successfully
May 8 22:31:34 localhost kernel: USB Mass Storage device found at 3
May 8 22:31:34 localhost kernel: usbcore: registered new driver
usb-storage
May 8 22:31:34 localhost kernel: USB Mass Storage support registered.
May 8 22:31:34 localhost scsi.agent[20863]: sd_mod: loaded
sucessfully (for disk)
May 8 22:31:35 localhost udev[20835]: configured rule in
'/etc/udev/rules.d/z_hal-plugdev.rules[2]' applied, 'sda' becomes '%k'
May 8 22:31:35 localhost udev[20835]: creating device node '/dev/sda'
May 8 22:31:35 localhost udev[20883]: configured rule in
'/etc/udev/rules.d/z_hal-plugdev.rules[2]' applied, 'sda1' becomes '%k'
May 8 22:31:35 localhost udev[20883]: creating device node '/dev/sda1'
-----------------------
Executando lsusb -v 1:3, tenho:
-----------------------
Bus 001 Device 003: ID 0781:5150 SanDisk Corp. SDCZ2 Cruzer Mini Flash
Drive (thin)
Device Descriptor:
...
idVendor 0x0781 SanDisk Corp.
idProduct 0x5150 SDCZ2 Cruzer Mini Flash Drive (thin)
bcdDevice 0.10
iManufacturer 1 SanDisk Corporation
iProduct 2 Cruzer Mini
iSerial 3 SNDK4D3D7422E4701402
...
-----------------------
Será que tem algum jeito de reconhecer automaticamente o device
recém-plugado (talvez pelo idProduct e pelo iSerial) e montá-lo em algum
lugar (por exemplo, /media/memkeyN)?
Fuçando o syslog, o arquivo de configuração
'/etc/udev/rules.d/z_hal-plugdev.rules' me chamou a atenção, mas ele tem
só seguinte conteúdo:
-----------------------
# put removable IDE/SCSI devices into the hal group instead of 'disk'
BUS="scsi",KERNEL="sd[a-z]*", PROGRAM="/etc/udev/scripts/device-removable.sh
%k", RESULT="1", NAME="%k", MODE="0640", GROUP="hal"
# BUS="ide", KERNEL="hd[a-z]*", PROGRAM="/etc/udev/scripts/device-removable.sh
%k", RESULT="1", NAME="%k", MODE="0640", GROUP="hal"
BUS="usb", KERNEL="ub[a-z]*", NAME="%k", MODE="0640", GROUP="hal"
-----------------------
--
Feng <redbrick1 at terra dot com dot br>
--
To UNSUBSCRIBE, email to [EMAIL PROTECTED]
with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
