Opa, desculpe pessoal. A luz ascende, mas na cor vermelha.
Rondineli Saad wrote:
Olá Pessoal, vejam se podem me ajudar. Estou tentando fazer o wireless
funcionar no meu notebook, mas nada acontece. A luz que indica o sinal
wireless não ascender (geralmente no ruindows ascende). Abaixo segue
os passos que segui para configurar a placa:
Notebook: hp pavillion dv 6000
Placa wireless:03:00.0 Network controller: Broadcom Corporation Dell
Wireless 1390 WLAN Mini-PCI Card (rev 01)
baixei o driver da fabricante hp correspondente
instalei o ndiswrapper e cabextract e o
bcm43xx-fwcutter_20060501-5_amd64.deb
descompactei o driver com o cabextract e instalei com o ndiswrapper -i
modelo.inf
rodei o comando
ndiswrapper -l
Installed ndis drivers:
bcmwl5 driver present, hardware present
rodei o comando
modprobe ndiswrapper
funcionou ok
a saida do comando lsmod
module size Used by
ndiswrapper 213352 0
comando iwconfig
wlan0 IEEE 802.11b/g ESSID:off/any Nickname:"Broadcom 4311"
Mode:Managed Frequency=2.484 GHz Access Point: Invalid
Bit Rate=1 Mb/s
RTS thr:off Fragment thr:off
Encryption key:off
Link Quality=0/100 Signal level=-256 dBm Noise level=-256 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
#ifconfig wlan0 up
#ifconfig
eth0 Link encap:Ethernet HWaddr 00:19:BB:EB:EB:A0
inet addr:10.100.10.22 Bcast:10.100.255.255 Mask:255.255.0.0
inet6 addr: fe80::219:bbff:feeb:eba0/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:509505 errors:0 dropped:0 overruns:0 frame:0
TX packets:274259 errors:3 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:285123458 (271.9 MiB) TX bytes:159956108 (152.5 MiB)
Interrupt:20 Base address:0xc000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:2022 errors:0 dropped:0 overruns:0 frame:0
TX packets:2022 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:62490 (61.0 KiB) TX bytes:62490 (61.0 KiB)
wlan0 Link encap:Ethernet HWaddr 00:14:A5:FB:54:A5
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:462 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:19404 (18.9 KiB)
Interrupt:255
#iwlist wlan0 scanning
#wlan0 No scan results (Geralmente, não demora 2 segundos já
aparece esta mensagem)
qualquer tentativa após isso não encontra a rede
Entrei em alguns tutoriais , efetuei os testes mas não consegui fazer
funcionar alguem pode me ajudar ?
--
To UNSUBSCRIBE, email to [EMAIL PROTECTED]
with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]