Marcelo, On Thursday 20 July 2006 10:42, Marcelo Luiz de Laia wrote: > Ola, > > Eu fiz a instalacao do lm-sensors via apt-get e ele esta rodando legal. > > No entanto, ele nao esta pegando as temperaturas e velocidades dos fans > de maneira correta. > > Alguem que usa essa mesma placa que eu poderia me dar umas dicas de onde > mexer nos arquivos de configuracoes para poder ajustar o meu sistema? > > Inclusive, ele mostra 5 temperaturas diferentes, sendo duas delas para a > CPU: uma para intel e outra para AMD. No entanto, eu so tenho AMD. Onde > estaria o pulo do gato?
eu tenho uma A7V600-X e tive que fazer algumas alterações na configuração do meu lm-sensors. Não pude conferir tudo, pq minha BIOS não mostra os alores pra -12V e -5V. Além disso, a minha usa o módulo it87, que é diferente da sua. Mesmo assim, deixo as minhas modificações para referência. Segue meu /etc/sensors.conf. Para detalhes, o man é seu amigo. abraços FF --- # A7V600-X chip "it87-*" "it8712-*" #set beep_enable 1 # Voltage monitors as advised in the It8705 data sheet label in0 "VCore 1" label in1 "VCore 2" label in2 "+3.3V" label in3 "+5V" label in4 "+12V" label in5 "-12V" label in6 "-5V" label in7 "Stdby" label in8 "VBat" # vid is not monitored by IT8705F # ignore vid # Only one core ignore in1 # Not -12V and -5V ignore in5 ignore in6 #The Core voltage is shifted for .13 volt, so correcting compute in0 -0.13+@ , @+0.13 # Same as original compute in3 ((6.8/10)+1)*@ , @/((6.8/10)+1) compute in4 ((30/10) +1)*@ , @/((30/10) +1) compute in7 ((6.8/10)+1)*@ , @/((6.8/10)+1) set in0_min 1.6 * 0.95 set in0_max 1.6 * 1.05 set in1_min 2.4 set in1_max 2.6 set in2_min 3.3 * 0.95 set in2_max 3.3 * 1.05 set in3_min 5.0 * 0.95 set in3_max 5.0 * 1.05 set in4_min 12 * 0.95 set in4_max 12 * 1.05 # -12V and -5V can't be checked, but they stay here anyway set in5_max -12 * 0.95 set in5_min -12 * 1.05 set in6_max -5 * 0.95 set in6_min -5 * 1.05 set in7_min 5 * 0.95 set in7_max 5 * 1.05 #the chip does not support in8 min/max # Temperature # # 2 = thermistor; 3 = thermal diode; 0 = unused set sensor1 2 set sensor2 2 set sensor3 0 label temp1 "CPU Temp" set temp1_over 45 set temp1_low 15 label temp2 "M/B Temp" set temp2_over 40 set temp2_low 15 ignore temp3 # Fans # CPU Fan compute fan1 -200 +@, @+200 set fan1_min 3000 # Case Fan set fan2_min 3000 ignore fan2 ignore fan3 --- -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]