Ola a toda la lista!!
Tengo un problema con mi regrabadora. Es una IDE y al compilar el nucleo(
2.4.19), le puse la opcion de scsi emulation. Pues bien, ahora no puedo aceder
al cdrom. Ni como lectura ni menos, para grabar.
Al ejecutar un mount /cdrom me falla el comando: sistema de archivos
incorrecto.( could this be the IDE device where you in fact use ide-scsi so
taht sr0 or sda or sa is needed).
Alguien que sepa lo q se hace, me echa una manita, pa ver si solucionamos esto
y acabamos de montar mi makina sobre linux ( debian 3.0)?.
Por si os es de ayuda os mando dos ficheros:
- uno es la salida del dmesg
- otro es dmesg |grep scsi
Pues .........Gracias.
Saluzzzzzzzzzzzzzzzzzzzzzzz
Linux version 2.4.19 ([EMAIL PROTECTED]) (gcc version 2.95.4 20011002 (Debian
prerelease)) #2 SMP mar nov 19 20:16:25 CET 2002
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000007ff0000 (usable)
BIOS-e820: 0000000007ff0000 - 0000000007ff3000 (ACPI NVS)
BIOS-e820: 0000000007ff3000 - 0000000008000000 (ACPI data)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
127MB LOWMEM available.
Advanced speculative caching feature not present
On node 0 totalpages: 32752
zone(0): 4096 pages.
zone(1): 28656 pages.
zone(2): 0 pages.
Kernel command line: BOOT_IMAGE=Linux-2.4.19 ro root=306 hdc=ide-scsi
ide_setup: hdc=ide-scsi
Local APIC disabled by BIOS -- reenabling.
Found and enabled local APIC!
Initializing CPU#0
Detected 800.054 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 1595.80 BogoMIPS
Memory: 126348k/131008k available (1643k kernel code, 4272k reserved, 647k
data, 120k init, 0k highmem)
Dentry cache hash table entries: 16384 (order: 5, 131072 bytes)
Inode cache hash table entries: 8192 (order: 4, 65536 bytes)
Mount-cache hash table entries: 2048 (order: 2, 16384 bytes)
Buffer-cache hash table entries: 4096 (order: 2, 16384 bytes)
Page-cache hash table entries: 32768 (order: 5, 131072 bytes)
CPU: Before vendor init, caps: 0183fbff c1c7fbff 00000000, vendor = 2
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 64K (64 bytes/line)
CPU: After vendor init, caps: 0183fbff c1c7fbff 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0183fbff c1c7fbff 00000000 00000000
CPU: Common caps: 0183fbff c1c7fbff 00000000 00000000
Enabling fast FPU save and restore... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
CPU: Before vendor init, caps: 0183fbff c1c7fbff 00000000, vendor = 2
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 64K (64 bytes/line)
CPU: After vendor init, caps: 0183fbff c1c7fbff 00000000 00000000
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0183fbff c1c7fbff 00000000 00000000
CPU: Common caps: 0183fbff c1c7fbff 00000000 00000000
CPU0: AMD Duron(tm) Processor stepping 01
per-CPU timeslice cutoff: 182.79 usecs.
SMP motherboard not detected.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 800.0407 MHz.
..... host bus clock speed is 200.0102 MHz.
cpu: 0, clocks: 2000102, slice: 1000051
CPU0<T0:2000096,T1:1000032,D:13,S:1000051,C:2000102>
Waiting on wait_init_idle (map = 0x0)
All processors have done init_idle
PCI: PCI BIOS revision 2.10 entry at 0xfb370, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
Disabling VIA memory write queue (PCI ID 0305, rev 03): [55] 89 & 1f -> 09
Unknown bridge resource 0: assuming transparent
Unknown bridge resource 1: assuming transparent
Unknown bridge resource 2: assuming transparent
PCI: Using IRQ router VIA [1106/0686] at 00:07.0
PCI: Disabling Via external APIC routing
isapnp: Scanning for PnP cards...
isapnp: SB audio device quirk - increasing port range
isapnp: AWE32 quirk - adding two ports
isapnp: Card 'Creative SB AWE64 PnP'
isapnp: 1 Plug & Play card detected total
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
Journalled Block Device driver loaded
Installing knfsd (copyright (C) 1996 [EMAIL PROTECTED]).
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI
ISAPNP enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller on PCI bus 00 dev 39
VP_IDE: detected chipset, but driver not compiled in!
VP_IDE: chipset revision 16
VP_IDE: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xe000-0xe007, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xe008-0xe00f, BIOS settings: hdc:DMA, hdd:DMA
hda: ST340810A, ATA DISK drive
hdc: HL-DT-ST GCE-8160B, ATAPI CD/DVD-ROM drive
hdd: GCD-R580B, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: 78165360 sectors (40021 MB) w/2048KiB Cache, CHS=4865/255/63
hdd: ATAPI 8X CD-ROM drive, 128kB Cache
Uniform CD-ROM driver Revision: 3.12
Partition check:
hda: hda1 hda2 < hda5 hda6 >
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 94M
agpgart: Detected Via Apollo Pro KT133 chipset
agpgart: AGP aperture is 64M @ 0xd0000000
[drm] Initialized tdfx 1.0.0 20010216 on minor 0
[drm] AGP 0.99 on VIA Apollo KT133 @ 0xd0000000 64MB
[drm] Initialized radeon 1.1.1 20010405 on minor 1
SCSI subsystem driver Revision: 1.00
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: HL-DT-ST Model: CD-RW GCE-8160B Rev: 1.01
Type: CD-ROM ANSI SCSI revision: 02
es1370: version v0.37 time 20:06:06 Nov 19 2002
es1371: version v0.30 time 20:06:09 Nov 19 2002
Linux Kernel Card Services 3.1.22
options: [pci] [cardbus] [pm]
usb.c: registered new driver hub
uhci.c: USB Universal Host Controller Interface driver v1.1
PCI: Found IRQ 9 for device 00:07.2
PCI: Sharing IRQ 9 with 00:07.3
uhci.c: USB UHCI at I/O 0xe400, IRQ 9
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Found IRQ 9 for device 00:07.3
PCI: Sharing IRQ 9 with 00:07.2
uhci.c: USB UHCI at I/O 0xe800, IRQ 9
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
usb.c: registered new driver usblp
printer.c: v0.11: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 8192 bind 8192)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
ds: no socket drivers loaded!
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 120k freed
hub.c: USB new device connect on bus1/2, assigned device number 2
spurious 8259A interrupt: IRQ7.
printer.c: usblp0: USB Bidirectional printer dev 2 if 0 alt 0 proto 2 vid
0x03F0 pid 0x0904
Adding Swap: 401584k swap-space (priority -1)
ide-scsi: hdc: unsupported command in request queue (0)
end_request: I/O error, dev 16:00 (hdc), sector 64
isofs_read_super: bread failed, dev=16:00, iso_blknum=16, block=32
ide-scsi: hdc: unsupported command in request queue (0)
end_request: I/O error, dev 16:00 (hdc), sector 64
isofs_read_super: bread failed, dev=16:00, iso_blknum=16, block=32
ide-scsi: hdc: unsupported command in request queue (0)
end_request: I/O error, dev 16:00 (hdc), sector 64
isofs_read_super: bread failed, dev=16:00, iso_blknum=16, block=32
ide-scsi: hdc: unsupported command in request queue (0)
end_request: I/O error, dev 16:00 (hdc), sector 64
isofs_read_super: bread failed, dev=16:00, iso_blknum=16, block=32
ide-scsi: hdc: unsupported command in request queue (0)
end_request: I/O error, dev 16:00 (hdc), sector 64
isofs_read_super: bread failed, dev=16:00, iso_blknum=16, block=32
Kernel command line: BOOT_IMAGE=Linux-2.4.19 ro root=306 hdc=ide-scsi
ide_setup: hdc=ide-scsi
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
ide-scsi: hdc: unsupported command in request queue (0)
ide-scsi: hdc: unsupported command in request queue (0)
ide-scsi: hdc: unsupported command in request queue (0)
ide-scsi: hdc: unsupported command in request queue (0)
ide-scsi: hdc: unsupported command in request queue (0)
ide-scsi: hdc: unsupported command in request queue (0)
