> >> May 21 13:15:07 muso pppd[1020]: rcvd [IPCP ConfReq id=0x6 <compress VJ 0f > >> 00> <addr 195.64.64.1>] > >> May 21 13:15:07 muso pppd[1020]: sent [IPCP ConfRej id=0x6 <addr > >> 195.64.64.1>] > >> May 21 13:15:07 muso pppd[1020]: rcvd [IPCP ConfReq id=0x7 <addrs > >> 195.64.64.1 195.64.69.173> <compress VJ 0f 00>] > >> May 21 13:15:07 muso pppd[1020]: sent [IPCP ConfRej id=0x7 <addrs > >> 195.64.64.1 195.64.69.173>] > >> May 21 13:15:07 muso pppd[1020]: rcvd [IPCP ConfReq id=0x8 <compress VJ 0f > >> 00>] > > Your machine does not like the other ends idea of ip addresses. See the > ConfRejs.
This I don't understand, as "stelo", the computer that does work, gets identical "Confreq": From the ppp session I'm using to send this email message: Mar 21 12:32:49 stelo pppd[260]: sent [IPCP ConfRej id=0x6 <addr 195.64.64.1>] Mar 21 12:32:49 stelo pppd[260]: rcvd [IPCP ConfReq id=0x7 <addrs 195.64.64.1 195.64.69.171> <compress VJ 0f 00>] Mar 21 12:32:49 stelo pppd[260]: sent [IPCP ConfRej id=0x7 <addrs 195.64.64.1 195.64.69.171>] Mar 21 12:32:50 stelo pppd[260]: rcvd [IPCP ConfReq id=0x8 <compress VJ 0f 00>] Mar 21 12:32:50 stelo pppd[260]: sent [IPCP ConfAck id=0x8 <compress VJ 0f 00>] > Are you using static or dynamic ips ? Check out the "noipdefault" option > for ppp. Dynamic. And, I've added the noipdefault option to /etc/ppp/options, but that only results in muso (the one that doesn't work) to give up even faster. Also, all pppd/dip config files on both stelo and muso are (were) identical (and unchanged from the debian defualts). The dip script I'm using is this one: # cistron.dip # Inbellen bij Cistron Internet Services met gebruik van DIP # # 1) Vergeet niet je eigen inbel nummer evt. aan te passen. # Dit is 8800999 of 880999 # Zie http://www.cistron.nl/ voor jouw inbel nummer. # 2) Vergeet niet je eigen login naam en password in te vullen. # #main: # Set Maximum Transfer Unit. # Many servers use either 1500 or # 1006; check with your network admins when in doubt. #get $mtu 1500 # Maak van de PPP route de default route. default # Initialiseer het modem op de juiste COM poort en snelheid print Initialiseert modem op COM2 (/dev/modem) op 115200 Baud... port ttyS3 if $errlvl != 0 goto bad_tty speed 57600 # Reset modem en seriele lijn. reset # Voorbereiden op inbellen echo on print Verstuur init string naar het modem... reinit: send ATZ\r wait OK 3 call_remote: print print Ik bel Cistron Internet Services (8800999), even geduld a.u.b. dial 8800999 if $errlvl == 1 goto login if $errlvl == 3 goto call_remote print error? goto reinit # Ok dan, modem opgenomen, nu door naar het inloggen login: print Connected! Ik probeer in te loggen wait ogin: if $errlvl != 0 goto error # Vergeet geen "P" voor de loginnaam te plaatsen om PPP direct te starten! # De \n moet gewoon blijven staan. send Pjoostje\n wait assword: if $errlvl != 0 goto error send Darwish0\n # Het inloggen is gelukt loggedin: # Proberen van het binnenhalen van het toegewezen IP nummer get $local remote if $errlvl != 0 goto call_remote # Proberen de juiste netmask binnen te halen # (normaal gesproken 255.255.255.255). get $mask 255.255.0.0 get $remote remote if $errlvl != 0 goto call_remote done: print print print CONNECTED to $remote at $rmtip (cistron.nl) print GATEWAY address $rmtip print LOCAL address $local mode PPP goto exit error: print PPP to $remote is niet gelukt. exit: ------------------------------- Thanks! [EMAIL PROTECTED] -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]