SCSI emulation for IDE CD-writer

[Steve Doerr]

I just installed and burned a cd per the cd writing howto, but now I can't find what to mount to read it.

It's not at scd0 or scsi0 and I'm not sure how to find it.

Does anyone know how to find it or see anything wrong with how I set this up?

Thanks for any input,
Steve

relevant info:

kern.log (ver 2.4.17)
Dec 28 12:42:04 debian kernel: ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Dec 28 12:42:04 debian kernel: VP_IDE: IDE controller on PCI bus 00 dev 39
Dec 28 12:42:04 debian kernel: VP_IDE: chipset revision 16
Dec 28 12:42:04 debian kernel: VP_IDE: not 100%% native mode: will probe irqs later
Dec 28 12:42:04 debian kernel: ide0: BM-DMA at 0xa000-0xa007, BIOS settings: hda:DMA, hdb:DMA
Dec 28 12:42:04 debian kernel: ide1: BM-DMA at 0xa008-0xa00f, BIOS settings: hdc:DMA, hdd:DMA
Dec 28 12:42:04 debian kernel: hda: Maxtor 51536H2, ATA DISK drive
Dec 28 12:42:04 debian kernel: hdb: LITE-ON LTR-48246S, ATAPI CD/DVD-ROM drive
Dec 28 12:42:04 debian kernel: hdc: MAXTOR 6L080J4, ATA DISK drive
Dec 28 12:42:04 debian kernel: hdd: CD-ROM Drive/F5A, ATAPI CD/DVD-ROM drive
Dec 28 12:42:04 debian kernel: ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Dec 28 12:42:04 debian kernel: ide1 at 0x170-0x177,0x376 on irq 15
Dec 28 12:42:04 debian kernel: hda: 30015216 sectors (15368 MB) w/2048KiB Cache, CHS=1868/255/63
Dec 28 12:42:04 debian kernel: hdc: 156355584 sectors (80054 MB) w/1819KiB Cache, CHS=155114/16/63
Dec 28 12:42:04 debian kernel: Partition check:
Dec 28 12:42:04 debian kernel: hda: hda1 hda2 hda3
Dec 28 12:42:04 debian kernel: hdc: hdc1 hdc2 hdc3
cut********************************
Dec 28 12:42:04 debian kernel: SCSI subsystem driver Revision: 1.00
Dec 28 12:42:04 debian kernel: scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Dec 28 12:42:04 debian kernel: Vendor: LITE-ON Model: LTR-48246S Rev: SS06
Dec 28 12:42:04 debian kernel: Type: CD-ROM ANSI SCSI revision: 02
Dec 28 12:42:04 debian kernel: Vendor: CD-ROM Model: Drive/F5A Rev: B1.4
Dec 28 12:42:04 debian kernel: Type: CD-ROM ANSI SCSI revision: 02

lilo.conf
append="hdb=ide-scsi hdd=ide-scsi"

modules.conf
### update-modules: start processing /etc/modutils/cdr
options ide-cd ignore='hdb hdd'
pre-install sg modprobe ide-scsi
### update-modules: end processing /etc/modutils/cdr


--
To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]