hi Ship's Log, Lt. Paulo Henrique Baptista de Oliveira, Stardate 230199.0551: > Hi Debian users, > a friend of mine has a ess1688 sound card and cant configure it in > Linux. Anyone has a light? > Have a nice day, Paulo Henrique >
I have such a card running (well with some problems...) *OOPS* I just realized that I have a 1868 (according to the isapnp output ... But then again : cat /dev/sndstat [EMAIL PROTECTED](p1)[776|0]Sat-23-01-1999 OSS/Free:3.8s2++-971130 Load type: Driver loaded as a module Kernel: Linux Aleph 2.1.125 #1 Thu Dec 3 14:08:52 CET 1998 i586 Config options: 0 Installed drivers: Card config: Audio devices: 0: ESS ES1688 AudioDrive (rev 11) (3.1) hmm... well .. check if that's for you :) ok ... here is my config: - sound is compiled as a soundblaster kernel module - /etc/modutils/options (or an other fle there) : options sb io=0x220 irq=9 dma=1 dma16=-1 options mpu401 io=0x330 options opl3 io=0x388 - /etc/isapnp.conf as atached If someone finds what's wrong ( I get DMA/IRQ conflikts sometimes ) please note. Greetings -- Alexander N. Benner - irc: #Hosanna - secret service sig : Do u really scan? MAT 10:26 for there is nothing covered, that shall not be revealed; and hid, that shall not be known. HDGFHEGFGDCAGBHDHEHCGPGOGPGNHJCAHAHCGPHEGFGDHEGFGE Uran Libia (I love Israel) North Korea RAF Sprengstoff Islam Plutonium Bomb
# $Id: pnpdump.c,v 1.1.1.2 1998/01/07 05:17:47 fred Exp $ # This is free software, see the sources for details. # This software has NO WARRANTY, use at your OWN RISK # # For details of this file format, see isapnp.conf(5) # # For latest information on isapnp and pnpdump see: # http://www.roestock.demon.co.uk/isapnptools/ # # Compiler flags: -DREALTIME -DNEEDSETSCHEDULER -DNEEDNANOSLEEP # # Trying port address 0203 # Board 1 has serial identifier 42 41 48 7d c8 01 22 8b 11 # Board 2 has serial identifier 27 ff ff ff ff 68 18 73 16 # (DEBUG) (READPORT 0x0203) (ISOLATE) (IDENTIFY *) # Card 1: (serial identifier 42 41 48 7d c8 01 22 8b 11) # Vendor Id DLK2201, Serial Number 1095269832, checksum 0x42. # Version 1.0, Vendor version 0.0 # ANSI string -->D-Link DE-220P PnP ISA Card<-- # # Logical device id DLK2201 # Device support I/O range check register # # Edit the entries below to uncomment out the configuration required. # Note that only the first value of any range is given, this may be changed if required # Don't forget to uncomment the activate (ACT Y) when happy (CONFIGURE DLK2201/1095269832 (LD 0 # Compatible device id PNP80d6 # Logical device decodes 10 bit IO address lines # Minimum IO base address 0x0240 # Maximum IO base address 0x0380 # IO base alignment 32 bytes # Number of IO addresses required: 32 (IO 0 (BASE 0x0240)) # IRQ 3, 5, 9, 10, 11, 12 or 15. # High true, edge sensitive interrupt (INT 0 (IRQ 9 (MODE +E))) #(ACT Y) )) # End tag... Checksum 0x00 (OK) # Card 2: (serial identifier 27 ff ff ff ff 68 18 73 16) # Vendor Id ESS1868, No Serial Number (-1), checksum 0x27. # Version 1.0, Vendor version 1.0 # ANSI string -->ESS ES1868 Plug and Play AudioDrive<-- # # Logical device id ESS0000 # # Edit the entries below to uncomment out the configuration required. # Note that only the first value of any range is given, this may be changed if required # Don't forget to uncomment the activate (ACT Y) when happy (CONFIGURE ESS1868/-1 (LD 0 # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0800 # Maximum IO base address 0x0ff8 # IO base alignment 8 bytes # Number of IO addresses required: 8 (IO 0 (BASE 0x0800)) (ACT Y) )) # # Logical device id ESS1868 # # Edit the entries below to uncomment out the configuration required. # Note that only the first value of any range is given, this may be changed if required # Don't forget to uncomment the activate (ACT Y) when happy (CONFIGURE ESS1868/-1 (LD 1 # Multiple choice time, choose one only ! # Start dependent functions: priority preferred # First DMA channel 1. # 8 bit DMA only # Logical device is not a bus master # DMA may execute in count by byte mode # DMA may not execute in count by word mode # DMA channel speed in compatible mode # (DMA 0 (CHANNEL 1)) # Next DMA channel 0 or 3. # 8 bit DMA only # Logical device is not a bus master # DMA may execute in count by byte mode # DMA may not execute in count by word mode # DMA channel speed in compatible mode #(DMA 1 (CHANNEL 0)) # IRQ 5. # High true, edge sensitive interrupt (by default) #(INT 0 (IRQ 5 (MODE +E))) # Fixed IO base address 0x0220 # Number of IO addresses required: 16 #(IO 0 (BASE 0x0220)) # Fixed IO base address 0x0388 # Number of IO addresses required: 4 # (IO 1 (BASE 0x0388)) # Fixed IO base address 0x0330 # Number of IO addresses required: 2 # (IO 2 (BASE 0x0330)) # Start dependent functions: priority acceptable # First DMA channel 1. # 8 bit DMA only # Logical device is not a bus master # DMA may execute in count by byte mode # DMA may not execute in count by word mode # DMA channel speed in compatible mode (DMA 0 (CHANNEL 1)) # Next DMA channel 0 or 3. # 8 bit DMA only # Logical device is not a bus master # DMA may execute in count by byte mode # DMA may not execute in count by word mode # DMA channel speed in compatible mode (DMA 1 (CHANNEL 0)) # IRQ 5, 7, 9 or 10. # High true, edge sensitive interrupt (by default) (INT 0 (IRQ 9 (MODE +E))) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0220 # Maximum IO base address 0x0240 # IO base alignment 32 bytes # Number of IO addresses required: 16 (IO 0 (BASE 0x0220)) # Fixed IO base address 0x0388 # Number of IO addresses required: 4 (IO 1 (BASE 0x0388)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0300 # Maximum IO base address 0x0330 # IO base alignment 48 bytes # Number of IO addresses required: 2 # (IO 2 (BASE 0x0300)) # Start dependent functions: priority acceptable # First DMA channel 0, 1 or 3. # 8 bit DMA only # Logical device is not a bus master # DMA may execute in count by byte mode # DMA may not execute in count by word mode # DMA channel speed in compatible mode # (DMA 0 (CHANNEL 0)) # Next DMA channel 0, 1 or 3. # 8 bit DMA only # Logical device is not a bus master # DMA may execute in count by byte mode # DMA may not execute in count by word mode # DMA channel speed in compatible mode # (DMA 1 (CHANNEL 0)) # IRQ 5, 7, 9, 10, 11 or 12. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 5 (MODE +E))) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0220 # Maximum IO base address 0x0280 # IO base alignment 32 bytes # Number of IO addresses required: 16 # (IO 0 (BASE 0x0220)) # Fixed IO base address 0x0388 # Number of IO addresses required: 4 # (IO 1 (BASE 0x0388)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0300 # Maximum IO base address 0x0330 # IO base alignment 48 bytes # Number of IO addresses required: 2 # (IO 2 (BASE 0x0300)) # Start dependent functions: priority acceptable # First DMA channel 0, 1 or 3. # 8 bit DMA only # Logical device is not a bus master # DMA may execute in count by byte mode # DMA may not execute in count by word mode # DMA channel speed in compatible mode # (DMA 0 (CHANNEL 0)) # Next DMA channel 0, 1 or 3. # 8 bit DMA only # Logical device is not a bus master # DMA may execute in count by byte mode # DMA may not execute in count by word mode # DMA channel speed in compatible mode # (DMA 1 (CHANNEL 0)) # IRQ 5, 7, 9, 10, 11 or 12. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 5 (MODE +E))) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0220 # Maximum IO base address 0x0280 # IO base alignment 32 bytes # Number of IO addresses required: 16 # (IO 0 (BASE 0x0220)) # Fixed IO base address 0x0388 # Number of IO addresses required: 4 # (IO 1 (BASE 0x0388)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0800 # Maximum IO base address 0x0ffe # IO base alignment 2 bytes # Number of IO addresses required: 2 # (IO 2 (BASE 0x0800)) # Start dependent functions: priority functional # First DMA channel 0, 1 or 3. # 8 bit DMA only # Logical device is not a bus master # DMA may execute in count by byte mode # DMA may not execute in count by word mode # DMA channel speed in compatible mode # (DMA 0 (CHANNEL 0)) # Next DMA channel 0, 1 or 3. # 8 bit DMA only # Logical device is not a bus master # DMA may execute in count by byte mode # DMA may not execute in count by word mode # DMA channel speed in compatible mode # (DMA 1 (CHANNEL 0)) # IRQ 5, 7, 9, 10, 11 or 12. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 5 (MODE +E))) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0220 # Maximum IO base address 0x0280 # IO base alignment 32 bytes # Number of IO addresses required: 16 # (IO 0 (BASE 0x0220)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0800 # Maximum IO base address 0x0ffc # IO base alignment 4 bytes # Number of IO addresses required: 4 # (IO 1 (BASE 0x0800)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0800 # Maximum IO base address 0x0ffe # IO base alignment 2 bytes # Number of IO addresses required: 2 # (IO 2 (BASE 0x0800)) # End dependent functions (ACT Y) )) # # Logical device id ESS0001 # # Edit the entries below to uncomment out the configuration required. # Note that only the first value of any range is given, this may be changed if required # Don't forget to uncomment the activate (ACT Y) when happy (CONFIGURE ESS1868/-1 (LD 2 # Multiple choice time, choose one only ! # Start dependent functions: priority preferred # Fixed IO base address 0x0201 # Number of IO addresses required: 1 # (IO 0 (BASE 0x0201)) # Start dependent functions: priority acceptable # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0200 # Maximum IO base address 0x020f # IO base alignment 1 bytes # Number of IO addresses required: 1 (IO 0 (BASE 0x0200)) # End dependent functions # Compatible device id PNPb02f # (ACT Y) )) # # Logical device id ESS0002 # # Edit the entries below to uncomment out the configuration required. # Note that only the first value of any range is given, this may be changed if required # Don't forget to uncomment the activate (ACT Y) when happy (CONFIGURE ESS1868/-1 (LD 3 # Multiple choice time, choose one only ! # Start dependent functions: priority preferred # IRQ 12. # High true, edge sensitive interrupt (by default) (INT 0 (IRQ 12 (MODE +E))) # Fixed IO base address 0x0168 # Number of IO addresses required: 8 (IO 0 (BASE 0x0168)) # Fixed IO base address 0x036e # Number of IO addresses required: 2 # (IO 1 (BASE 0x036e)) # Start dependent functions: priority acceptable # IRQ 10 or 11. # High true, edge sensitive interrupt (by default) #(INT 0 (IRQ 10 (MODE +E))) # Fixed IO base address 0x0168 # Number of IO addresses required: 8 #(IO 0 (BASE 0x0168)) # Fixed IO base address 0x036e # Number of IO addresses required: 2 (IO 1 (BASE 0x036e)) # Start dependent functions: priority acceptable # IRQ 10, 11 or 12. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 10 (MODE +E))) # Fixed IO base address 0x01e8 # Number of IO addresses required: 8 # (IO 0 (BASE 0x01e8)) # Fixed IO base address 0x03ee # Number of IO addresses required: 2 # (IO 1 (BASE 0x03ee)) # Start dependent functions: priority functional # IRQ 10, 11 or 12. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 10 (MODE +E))) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0100 # Maximum IO base address 0x01f8 # IO base alignment 8 bytes # Number of IO addresses required: 8 # (IO 0 (BASE 0x0100)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0300 # Maximum IO base address 0x03fe # IO base alignment 2 bytes # Number of IO addresses required: 2 # (IO 1 (BASE 0x0300)) # End dependent functions # Compatible device id PNP0600 # (ACT Y) )) # End tag... Checksum 0x00 (OK) # Returns all cards to the "Wait for Key" state #(DEBUG) (WAITFORKEY)
