* Hugo Graumann ([EMAIL PROTECTED]) wrote: > * On Fri, Feb 07, 2003 at 12:00:17AM +0100, mess-mate ([EMAIL PROTECTED]) wrote: > > Hi, > > > > On Tue, 4 Feb 2003 09:42:11 -0700 > > Hugo Graumann <[EMAIL PROTECTED]> wrote: > > > > | * On Mon, Feb 03, 2003 at 02:19:45PM -0500, karrottop ([EMAIL PROTECTED]) wrote: > > | > > > | > I am re-posting this because I was made aware I sent it as a reply to > > | > another post. Sorry about that, so without further adue here is my > > | > intended post now... > > | > > > | > > > | > I am having a great deal of trouble getting lm_sensors to work under > > | > debian. I am pretty sure that I am about 75% on the way to getting this > > | > started but none the less, if someone could give me a bit of a > > | > walk-through to getting things running I would appreciate it. My > > | > intention is mostly to monitor my hardware temp's etc, being that I am > > | > using a water cooled system, and I am a bit uneasy about not knowing the > > | > performance of my system, especially one that is overclocked. If it > > | > matters I am using sid, a soyo motherboard with a via chipset, and > > | > kernel 2.4.20 ( I have built in everything in the i2c portion of > > | > charcter devices ) > > | > > > | > > > | > > > | > -- > > | > To UNSUBSCRIBE, email to [EMAIL PROTECTED] > > | > with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED] > > | > > > | > > | Got hardware sensors working on a few motherboards here and even > > | took notes on how it was done. Perhaps these notes might be useful to you. > > | > > | Notes on Installing sensor support in a Debian system. > > | > > | 0) For the following, it is assumed that a new > > | 2.4.20 kernel was already compiled, installed and > > | working. It is also assumed that the kernel was compiled > > | using the debian kernel build system make-kpkg. The > > | kernel source should be in /usr/src/linux either directly > > | or by a symbolic link. > > | > > | 1) have a working 2.4 series kernel with module support > > | included. Make sure that i2o items are NOT compiled > > | in. Once this kernel is installed and working, the modules > > | are ready to be included. Make sure you are running > > | the kernel to which the modules are to be added. This > > | seems to be the easiest way to make the module version > > | numbers consistent with the kernel version number. > > | > > | 2) obtain the debian packages: i2c-source,lm-sensors, > > | lm-sensors-source, and sensord. Optionally also > > | get other monitors like sensor-sweep-applet, > > | wmsensors or xsensors. The package xsensors is > > | not in woody but getting the source and building > > | it locally using apt-get source works fine. > > | > > | 3) Become root and change to the /usr/src directory. > > | In this directory there will be tar files named > > | i2c.tar.gz and lm-sensors.tar.gz. When these > > | tar files are expanded they write themselves > > | into the /usr/src/modules directory. This > > | directory may already exist if other modules > > | have already been installed in this kernel. > > | > > | 4) Extract the files by "tar zxf i2c.tar.gz" and > > | "tar zxf lm-sensors.tar.gz" > > | > > | 5) cd /usr/src/linux and run the command > > | "make-kpkg modules_image" > > | When the build has completed there will be > > | debian packages in /usr/src named > > | i2c-2.4.19_2.6.5-3+lb.custom.1.1_i386.deb > > | and > > | lm-sensors-2.4.19_2.6.4-3+lb.custom.1.1_i386.deb > > | > > | 6) install these packages with the commands > > | dpkg -i i2c-2.4.19_2.6.5-3+lb.custom.1.1_i386.deb > > | and > > | dpkg -i lm-sensors-2.4.19_2.6.4-3+lb.custom.1.1_i386.deb > > Sorry, this error messages appaers on the install of this i2c package : > > dpkg: dependency problems prevent configuration of i2c-2.4.20: > > i2c-2.4.20 depends on kernel-image-2.4.20; however: > > Package kernel-image-2.4.20 is not installed. > > dpkg: error processing i2c-2.4.20 (--install): > > dependency problems - leaving unconfigured > > Errors were encountered while processing: > > i2c-2.4.20 > > ?? This kernel is installed ! Compiled and installed by myself. > > (with the old method) > > What has I do other ? > > mess-mate > > If by old method you mean "make bzimage" etc, then I bet that is > why the package wont install. Looks like the i2c package wants to > see a 2.4.20 kernel installed as a Debian package before it is > satisfied. So even though you have a running 2.4.20 kernel, the > Debian package system doesn't know about it. I guess one fix > would be to make a kernel the Debian way with make-kpkg and > then install that kernel package (this is sort of implied in step 0). > After this you have a 2.4.20 kernel and the packaging system knows about > it as well so the dependencies will be correct. > > > > > | > > | 7) As root (as always) run the program sensors-detect. > > | This tool sweeps the smbus and determines the devices > > | that are on it. It then reports the chip types and > > | the relevant modules that need to be loaded to get the > > | hardware sensors system working. This program mostly > > | works but does not always work. See the last step for > > | suggestions if the modules were detected incorrectly. > > | > > | 8) Cut and paste the results from sensors-detect into > > | the relevant files as it requests. For one motherboard > > | as an example, > > | the lines: > > | # I2C adapter drivers > > | i2c-viapro > > | # I2C chip drivers > > | w83781d > > | have to be pasted into the file /etc/modules. > > | Then the command update-modules has to be run. > > | Then paste the lines > > | # I2C module options > > | alias char-major-89 i2c-dev > > | into the file /etc/modutils/local > > | > > | Then run the command /etc/init.d/modutils > > | > > | 9) After these steps are completed, the required > > | modules will be loaded. This can be checked by > > | the output of the lsmod command. The output for > > | this example is > > | Module Size Used by Tainted: P > > | w83781d 19224 0 (unused) > > | i2c-proc 6416 0 [w83781d] > > | i2c-viapro 3860 0 (unused) > > | i2c-core 15052 0 [w83781d i2c-proc i2c-viapro] > > | > > | 10) Then reboot the system. If the module system > > | is working correctly then after boot the loaded > > | modules should be identical to the previous output > > | of lsmod > > | > > | 11) To verify that the kernel interface is correctly tied > > | to the hardware run the command "sensors" > > | Typical output in this example is > > | w83782d-i2c-0-2d > > | Adapter: SMBus Via Pro adapter at e800 > > | Algorithm: Non-I2C SMBus adapter > > | VCore 1: +1.77 V (min = +1.74 V, max = +1.93 V) (beep) > > | VCore 2: +2.51 V (min = +1.74 V, max = +1.93 V) (beep) > > | +3.3V: +3.32 V (min = +3.13 V, max = +3.45 V) (beep) > > | +5V: +5.07 V (min = +4.72 V, max = +5.24 V) (beep) > > | +12V: +12.46 V (min = +10.79 V, max = +13.19 V) > > | -12V: -12.29 V (min = -13.21 V, max = -10.90 V) > > | -5V: -5.45 V (min = -5.26 V, max = -4.76 V) > > | V5SB: +0.13 V (min = +0.13 V, max = +0.13 V) > > | VBat: +0.08 V (min = +0.08 V, max = +0.08 V) > > | fan1: 0 RPM (min = 3000 RPM, div = 2) (beep) > > | fan2: 0 RPM (min = 187 RPM, div = 32) (beep) > > | fan3: 0 RPM (min = 3000 RPM, div = 2) > > | temp1: +32°C (limit = +60°C) sensor = thermistor > (beep) > > | temp2: +33.5°C (limit = +60°C, hysteresis = +50°C) sensor = thermistor > (beep) > > | temp3: +255.5°C (limit = +60°C, hysteresis = +50°C) sensor = 3904 >transistor > > | vid: +1.850 V > > | alarms: > > | beep_enable: > > | Sound alarm disabled > > | > > | It is pretty important to confirm these values by comparing > > | them to the readings that the BIOS reports. If the numbers > > | match all is well. If the numbers dont match then you have > > | problems. One possibility is that the sensors-detect > > | program detected the wrong kind of hardware. Confirm what the > > | detected hardware matches the motherboard type. If the hardware > > | is correct confirm that the correct hardware module type is > > | enabled in the file "/etc/sensors.conf". This file controls the > > | translation from hardware digital numbers to human readable > > | floating point numbers. This file is heavily documented and > > | modifying it should be self-explanatory. > > | > > | 12) At this point the hardware sensor system is operational > > | and higher level tools like xsensors can be run. If the > > | output is correct then the interface to /proc/sys/dev/sensors > > | is also working > > | > > | 13) The highest level routines like sensord, ksensors, wmsensors, or > > | sensor_sweep_applet can now be configured to run as desired. > > | > > | 14) One some (maybe many motherboards) the above is sufficient > > | to get things working. But I had a couple of motherboard > > | types that failed in different ways. > > | > > | On one motherboard sensors-detect correctly detected > > | the hardware but on this motherboard (Asus P5A) the smbus is > > | known to be broken but the isa bus works and the hardware can > > | be accessed from there. Googling for "lm sensors Asus P5A" > > | led right to the lm sensors documentation which explained > > | that the problem is known and the workaround is to use the > > | isa bus. No explanation given as to how to do that. More > > | searching and tinkering led to the answer of putting the module > > | i2c-isa into the /etc/modules file. Then things started working. > > | > > | On another motherboard, (Gigabyte 7ZMMH) sensors-detect reported > > | the wrong hardware. Here the solution was to determine the actual > > | hardware on the motherboard. I found the site > > | http://mbm.livewiredev.com/ > > | to be helpful here. Then googling for combinations of the motherboard > > | hardware chipset and lm sensors led to a page where someone > > | kindly listed the modules required for this to work. After making > > | this change everything started working > > | > > | HTH > > | Cheers > > | > > | > > | > > | -- > > | To UNSUBSCRIBE, email to [EMAIL PROTECTED] > > | with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED] > > | > > > > > > -- > > Computers are like air conditioners, they are useless when you open > > Windows. > > Regards > > > -- > To UNSUBSCRIBE, email to [EMAIL PROTECTED] > with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
Well another way is, you'll get the tarball from lm-sensors website and patch it up with your current kernel. You'll need to re-compile your current kernel though. Regards, Jsen --- http://arsha.is.dreaming.org http://www.m0sh.net Wanting To Die Is Your Reason To Live -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
