Matt Matt Fair wrote:
Yes I have ide-cd built into the kernel and ide-scsi a module installed. My lsmod:Module Size Used by sr_mod 13112 0 (autoclean) sg 27716 0 ide-scsi 7424 0 scsi_mod 88920 3 [sr_mod sg ide-scsi] parport_pc 11976 0 (unused) parport 15008 0 [parport_pc]My computer reconizes my two cd drives as scsi drives but my first drive (hdc -> scd0) only works When I try to access my second drive(hdd ->scd1) my kernel crashes.My log output is: kernel: Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0 kernel: Attached scsi CD-ROM sr1 at scsi0, channel 0, id 1, lun 0 kernel: sr0: scsi3-mmc drive: 48x/48x cd/rw xa/form2 cdda tray kernel: Uniform CD-ROM driver Revision: 3.12 kernel: sr1: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray kernel: VFS: Disk change detected on device sr(11,1)kernel: scsi : aborting command due to timeout : pid 17, scsi0, channel 0, id 1, lun 0 Read (10) 00 00 00 00 10 00 00 01 00kernel: hdd: timeout waiting for DMA kernel: ide_dmaproc: chipset supported ide_dma_timeout func only: 14kernel: hdd: status error: status=0x58 { DriveReady SeekComplete DataRequest }kernel: hdd: drive not ready for command kernel: hdd: status timeout: status=0xd0 { Busy }kernel: ide-scsi: Strange, packet command initiated yet DRQ isn't assertedkernel: hdd: ATAPI reset complete kernel: hdd: irq timeout: status=0x80 { Busy }I have had this working before, but I just recently cleared off my machine and now I don't remember what I did. When I do a cdrecord -scanbus I get :Cdrecord 1.10 (i686-pc-linux-gnu) Copyright (C) 1995-2001 J?rg Schilling Linux sg driver version: 3.1.2. Using libscg version 'schily-0.5' scsibus0:cdrecord: Warning: controller returns wrong size for CD capabilities page.0,0,0 0) 'Lite-On ' 'LTN486 48x Max ' 'YD01' Removable CD-ROM 0,1,0 1) 'HP ' 'CD-Writer+ 8100 ' '1.0g' Removable CD-ROM 0,2,0 2) * 0,3,0 3) * 0,4,0 4) * 0,5,0 5) * 0,6,0 6) * 0,7,0 7) *I can access by first drive (hdc -> scd0) but when I try accessing my second drive (hdd -> scd1) everything freezes up and my kernel crashes.By boot up goes like this: .. kernel: ide_setup: hdc=ide-scsi kernel: ide_setup: hdd=ide-scsi ... hdc: Lite-On LTN486 48x Max, ATAPI CD/DVD-ROM drive hdd: Hewlett-Packard CD-Writer Plus 8100, ATAPI CD/DVD-ROM drive ... SCSI subsystem driver Revision: 1.00 scsi0 : SCSI host adapter emulation for IDE ATAPI devices Vendor: Lite-On Model: LTN486 48x Max Rev: YD01 Type: CD-ROM ANSI SCSI revision: 02 Vendor: HP Model: CD-Writer+ 8100 Rev: 1.0g Type: CD-ROM ANSI SCSI revision: 02 Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0 Attached scsi CD-ROM sr1 at scsi0, channel 0, id 1, lun 0 sr0: scsi3-mmc drive: 48x/48x cd/rw xa/form2 cdda tray Uniform CD-ROM driver Revision: 3.12 sr1: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray ... If anyone has any ideas this I would greatly apreciate your help. Thanks in advance, Matt Marc Wilson wrote:Do you have both ide-cd and ide-scsi built into the kernel? On Mon, Nov 05, 2001 at 04:42:01PM -0600, Matt Fair wrote:I have an ide cdwriter that I want to use. I had this working under woody but downgraded to 2.2r4 Potato (just installed it via network yesterday). I had ide-scsii a module but I rebuilt it as part of the kernel. I have modules sg and sr_mod installed.In my /etc/fstab I have: /dev/scd0 /cdrom iso9660 user,noexec,nodev,nosuid,ro,noauto 0 0 /dev/scd1 /hpcd iso9660 user,noexec,nodev,nosuid,rw,noauto 0 0 They both get the same error when I do mount /cdrom or mount /hpcd.What is wrong here, I know they work because I have gotten it to work when I had woody installed.Any sugestions? Thanks, Matt --To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact listm[EMAIL PROTECTED]