On Wed, Apr 24, 2002 at 06:42:09PM -0400, [EMAIL PROTECTED] wrote:
> I have a 1.5 Gbyte disk partitioned into 2 DOS drives, one 900 Mbyte
> (Windows), and the other 600 Mbyte. I want to use the 600 Mbyte for Linux.
> Using cfdisk in dbootstrap I configure two primary partitions in this drive,
> a Linux swap and a Linux native. I'd like to keep the Windows partition
> bootable, so it comes up by default, and I would like to boot linux from the
> floppy. Is this possible?
No problem. Just make a linux boot floppy. I think you are asked during the
installation process. And make sure you have the right boot priority in BIOS:
floppy before hard disk.
> Is there a better way?
Configure lilo so that it can boot both OSs and install it on the hard disk.
See man lilo. I attach my lilo.conf for your info.
HTH Joachim
--
Joachim Fahnenmüller
Lehrer für Mathematik und Physik
Herder-Gymnasium
Kattowitzer Straße 52
51065 Köln
# /etc/lilo.conf - See: `lilo(8)' and `lilo.conf(5)',
# --------------- `install-mbr(8)', `/usr/share/doc/lilo/',
# and `/usr/share/doc/mbr/'.
# +---------------------------------------------------------------+
# | !! Reminder !! |
# | |
# | Don't forget to run `lilo' after you make changes to this |
# | conffile, `/boot/bootmess.txt', or install a new kernel. The |
# | computer will most likely fail to boot if a kernel-image |
# | post-install script or you don't remember to run `lilo'. |
# | |
# +---------------------------------------------------------------+
# Support LBA for large hard disks.
#
lba32
# Specifies the boot device. This is where Lilo installs its boot
# block. It can be either a partition, or the raw device, in which
# case it installs in the MBR, and will overwrite the current MBR.
#
boot=/dev/hda
# Specifies the device that should be mounted as root. (`/')
#
root=/dev/hda4
# Enable map compaction:
# Tries to merge read requests for adjacent sectors into a single
# read request. This drastically reduces load time and keeps the
# map smaller. Using `compact' is especially recommended when
# booting from a floppy disk. It is disabled here by default
# because it doesn't always work.
#
# compact
# Installs the specified file as the new boot sector
#
install=/boot/boot.b
# Specifies the location of the map file
#
map=/boot/map
# You can set a password here, and uncomment the `restricted' lines
# in the image definitions below to make it so that a password must
# be typed to boot anything but a default configuration. If a
# command line is given, other than one specified by an `append'
# statement in `lilo.conf', the password will be required, but a
# standard default boot will not require one.
#
# This will, for instance, prevent anyone with access to the
# console from booting with something like `Linux init=/bin/sh',
# and thus becoming `root' without proper authorization.
#
# Note that if you really need this type of security, you will
# likely also want to use `install-mbr' to reconfigure the MBR
# program, as well as set up your BIOS to disallow booting from
# removable disk or CD-ROM, then put a password on getting into the
# BIOS configuration as well. Please RTFM `install-mbr(8)'.
#
# password=tatercounter2000
# Specifies the number of deciseconds (0.1 seconds) LILO should
# wait before booting the first image.
#
delay=20
# You can put a customized boot message up if you like. If you use
# `prompt', and this computer may need to reboot unattended, you
# must specify a `timeout', or it will sit there forever waiting
# for a keypress. `single-key' goes with the `alias' lines in the
# `image' configurations below. eg: You can press `1' to boot
# `Linux', `2' to boot `LinuxOLD', if you uncomment the `alias'.
#
message=/boot/bootmess.txt
prompt
# single-key
# delay=100
timeout=300
# Specifies the VGA text mode at boot time. (normal, extended, ask, <mode>)
#
# vga=ask
# vga=9
#
vga=normal
# Kernel command line options that apply to all installed images go
# here. See: The `boot-prompt-HOWO' and `kernel-parameters.txt' in
# the Linux kernel `Documentation' directory.
#
# append=""
# Boot up Linux by default.
#
default=Linux
image=/boot/vmlinuz
label=Linux
read-only
# restricted
alias=2
image=/boot/vmlinuz2
label=Linux2
read-only
optional
# restricted
alias=3
# If you have another OS on this machine to boot, you can uncomment the
# following lines, changing the device name on the `other' line to
# where your other OS' partition is.
#
other=/dev/hda1
label=Windows
# restricted
alias=1
table=/dev/hda