I found that my on-board 8139-C failed to receive packets if ACPI was compiled into the kernel; it might be worthwhile trying it without ACPI support if it's enabled, or tinkering with your in-kernel power management options.
~Tom White --------------------------------------------- http://www.oddquad.org/ --------------------------------------------- There's no future in time travel. On Mon, 4 Aug 2003, Robert Tilley wrote: > Date: Mon, 4 Aug 2003 16:20:59 -0400 > From: Robert Tilley <[EMAIL PROTECTED]> > To: [EMAIL PROTECTED] > Subject: RealTex 8139 Problem -- Dmesg output > Resent-Date: Sun, 3 Aug 2003 15:14:11 -0500 (CDT) > Resent-From: [EMAIL PROTECTED] > > I am including the entire output from dmesg in the hopes of successfully being > able to use my NIC. The relevant portions are highlighted. > > I am unable to use my D-Link RTL-8139 with any of kernel 2.4.19, 2.4.21, or > 2.6.0-test2 despite the Network Device explicitly being set to RTL-8139 with > make menuconfig. Dmesg reports that my NIC is found and the 8139too driver > loaded. But any attempt to load a web page resultcs in "Address not found". > Even a simple ping of 192.168.1.1 (address of my Linksys router) results in > Address Not Found. > > Any advice is most welcome. > > debian:/home/tilleyrw# cat dmesg.output > Linux version 2.4.21 ([EMAIL PROTECTED]) (gcc version 3.3.1 20030728 (Debian > prerelease)) #5 Mon Aug 4 15:30:10 EDT 2003 > BIOS-provided physical RAM map: > BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) > BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) > BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) > BIOS-e820: 0000000000100000 - 000000000c000000 (usable) > BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved) > 192MB LOWMEM available. > On node 0 totalpages: 49152 > zone(0): 4096 pages. > zone(1): 45056 pages. > zone(2): 0 pages. > Kernel command line: BOOT_IMAGE=Linux-stable ro root=301 > Initializing CPU#0 > Detected 601.380 MHz processor. > Console: colour VGA+ 80x25 > Calibrating delay loop... 1199.30 BogoMIPS > Memory: 191292k/196608k available (1838k kernel code, 4928k reserved, 638k > data, 108k init, 0k highmem) > Dentry cache hash table entries: 32768 (order: 6, 262144 bytes) > Inode cache hash table entries: 16384 (order: 5, 131072 bytes) > Mount cache hash table entries: 512 (order: 0, 4096 bytes) > Buffer-cache hash table entries: 16384 (order: 4, 65536 bytes) > Page-cache hash table entries: 65536 (order: 6, 262144 bytes) > CPU: L1 I cache: 16K, L1 D cache: 16K > CPU: L2 cache: 128K > Intel machine check architecture supported. > Intel machine check reporting enabled on CPU#0. > CPU: After generic, caps: 0383f9ff 00000000 00000000 00000000 > CPU: Common caps: 0383f9ff 00000000 00000000 00000000 > CPU: Intel Celeron (Coppermine) stepping 06 > Enabling fast FPU save and restore... done. > Enabling unmasked SIMD FPU exception support... done. > Checking 'hlt' instruction... OK. > POSIX conformance testing by UNIFIX > PCI: PCI BIOS revision 2.10 entry at 0xfb3b0, last bus=1 > PCI: Using configuration type 1 > PCI: Probing PCI hardware > PCI: Using IRQ router PIIX [8086/7110] at 00:07.0 > Limiting direct PCI/PCI transfers. > isapnp: Scanning for PnP cards... > isapnp: No Plug & Play device found > Linux NET4.0 for Linux 2.4 > Based upon Swansea University Computer Society NET3.039 > Initializing RT netlink socket > Starting kswapd > Journalled Block Device driver loaded > Installing knfsd (copyright (C) 1996 [EMAIL PROTECTED]). > parport0: PC-style at 0x378 [PCSPP(,...)] > pty: 256 Unix98 ptys configured > Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI > ISAPNP enabled > ttyS00 at 0x03f8 (irq = 4) is a 16550A > ttyS01 at 0x02f8 (irq = 3) is a 16550A > Real Time Clock Driver v1.10e > Floppy drive(s): fd0 is 1.44M > FDC 0 is a post-1991 82077 > 8139too Fast Ethernet driver 0.9.26 > PCI: Found IRQ 10 for device 00:0d.0 > *** > eth0: RealTek RTL8139 Fast Ethernet at 0xcc80d000, 00:50:ba:d1:73:9d, IRQ 10 > eth0: Identified 8139 chip type 'RTL-8139B' > *** > Linux agpgart interface v0.99 (c) Jeff Hartmann > agpgart: Maximum main memory to use for agp memory: 150M > agpgart: Detected Intel 440BX chipset > agpgart: AGP aperture is 64M @ 0xd0000000 > [drm] Initialized tdfx 1.0.0 20010216 on minor 0 > [drm] AGP 0.99 on Intel 440BX @ 0xd0000000 64MB > [drm] Initialized radeon 1.1.1 20010405 on minor 1 > [drm] AGP 0.99 on Intel 440BX @ 0xd0000000 64MB > [drm] Initialized i810 1.2.0 20010920 on minor 2 > Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4 > ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx > PIIX4: IDE controller at PCI slot 00:07.1 > PIIX4: chipset revision 1 > PIIX4: not 100% native mode: will probe irqs later > ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:pio > ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA > hda: Maxtor 90845D4, ATA DISK drive > blk: queue c03af800, I/O limit 4095Mb (mask 0xffffffff) > hdc: LITE-ON LTR-48125W, ATAPI CD/DVD-ROM drive > hdd: CD-202E, ATAPI CD/DVD-ROM drive > ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 > ide1 at 0x170-0x177,0x376 on irq 15 > hda: attached ide-disk driver. > hda: host protected area => 1 > hda: 16514064 sectors (8455 MB) w/256KiB Cache, CHS=16383/16/63, UDMA(33) > hdc: attached ide-cdrom driver. > hdc: ATAPI 48X CD-ROM CD-R/RW drive, 1984kB Cache, UDMA(33) > Uniform CD-ROM driver Revision: 3.12 > hdd: attached ide-cdrom driver. > hdd: ATAPI 12X CD-ROM drive, 120kB Cache, DMA > Partition check: > hda: hda1 hda2 hda3 hda4 > SCSI subsystem driver Revision: 1.00 > scsi0 : SCSI host adapter emulation for IDE ATAPI devices > Creative EMU10K1 PCI Audio Driver, version 0.20, 06:33:10 Jul 30 2003 > PCI: Found IRQ 11 for device 00:11.0 > PCI: Sharing IRQ 11 with 00:07.2 > emu10k1: EMU10K1 rev 5 model 0x21 found, IO at 0xe800-0xe81f, IRQ 11 > ac97_codec: AC97 codec, id: TRA35 (TriTech TR A5) > Linux Kernel Card Services 3.1.22 > options: [pci] [cardbus] [pm] > usb.c: registered new driver hub > host/uhci.c: USB Universal Host Controller Interface driver v1.1 > PCI: Found IRQ 11 for device 00:07.2 > PCI: Sharing IRQ 11 with 00:11.0 > host/uhci.c: USB UHCI at I/O 0xe000, IRQ 11 > usb.c: new USB bus registered, assigned bus number 1 > hub.c: USB hub found > hub.c: 2 ports detected > usb.c: registered new driver serial > usbserial.c: USB Serial Driver core v1.4 > usbserial.c: USB Serial support registered for Handspring Visor / Treo / Palm > 4.0 / Clié 4.x > usbserial.c: USB Serial support registered for Sony Clié 3.5 > visor.c: USB HandSpring Visor, Palm m50x, Treo, Sony Clié driver v1.7 > Initializing USB Mass Storage driver... > usb.c: registered new driver usb-storage > USB Mass Storage support registered. > NET4: Linux TCP/IP 1.0 for NET4.0 > IP Protocols: ICMP, UDP, TCP, IGMP > IP: routing cache hash table of 2048 buckets, 16Kbytes > TCP: Hash tables configured (established 16384 bind 32768) > NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. > ds: no socket drivers loaded! > VFS: Mounted root (ext2 filesystem) readonly. > Freeing unused kernel memory: 108k freed > Adding Swap: 374968k swap-space (priority -1) > eth0: Setting 100mbps full-duplex based on auto-negotiated partner ability > 41e1. > > -- > Comments are most appreciated, > > Robert Tilley > > > -- > To UNSUBSCRIBE, email to [EMAIL PROTECTED] > with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED] > > -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]