-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 - From Matt Harrison on Sat Dec 12:
> The other CD-DVD writer works like a charm, but this one does not, > whatever the interface. I had mainly tried with GNOME's built-in's > burning tool, but it explains me that I should try burning the CD/DVD > at a lower speed. I tried, but even in 1x speed (!) it still fails > after ~2 sec of burning. > > Any idea? > > Thanks. > -- > Merciadri Luca > See http://www.student.montefiore.ulg.ac.be/~merciadri/ > -- > To UNSUBSCRIBE, email to debian-user-requ...@lists.debian.org > with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org I just tried with gnomebaker (I did not know it). Really bad news. Writing a DVD-R (I never use DVD+R, and they should be `less well' supported by my DVD writer): == Executing 'genisoimage -gui -V GnomeBaker data disk -A GnomeBaker -p Luca Merciadri -iso-level 3 -l -r -hide-rr-moved -J -joliet-long -graft-points --path-list /tmp/GnomeBaker-merciadriluca/gnomebaker-DPJ84U | builtin_dd of=/dev/sr0 obs=32k seek=0' I: -input-charset not specified, using utf-8 (detected in locale settings) /dev/sr0: "Current Write Speed" is 1.0x1352KBps. :-[ wr...@lba=0h failed with SK=5h/CANNOT WRITE MEDIUM - INCOMPATIBLE FORMAT]: Wrong medium type :-( media is not formatted or unsupported. :-( write failed: Wrong medium type == Writing a CD-R: == wodim: No write mode specified. wodim: Asuming -tao mode. wodim: Future versions of wodim may have different drive dependent defaults. wodim: Operation not permitted. Warning: Cannot raise RLIMIT_MEMLOCK limits.scsidev: '/dev/sr0' devname: '/dev/sr0' scsibus: -2 target: -2 lun: -2 Linux sg driver version: 3.5.27 Wodim version: 1.1.9 SCSI buffer size: 64512 Beginning DMA speed test. Set CDR_NODMATEST environment variable if device communication breaks or freezes immediately after that. TOC Type: 3 = CD-ROM XA mode 2 Device type : Removable CD-ROM Version : 5 Response Format: 2 Capabilities : Vendor_info : '_NEC ' Identification : 'DVD_RW ND-2500A ' Revision : '1.06' Device seems to be: Generic mmc2 DVD-R/DVD-RW. Current: 0x0009 (CD-R) Profile: 0x001B (DVD+R) Profile: 0x001A (DVD+RW) Profile: 0x0014 (DVD-RW sequential recording) Profile: 0x0013 (DVD-RW restricted overwrite) Profile: 0x0011 (DVD-R sequential recording) Profile: 0x0010 (DVD-ROM) Profile: 0x000A (CD-RW) Profile: 0x0009 (CD-R) (current) Profile: 0x0008 (CD-ROM) (current) Using generic SCSI-3/mmc CD-R/CD-RW driver (mmc_cdr). Driver flags : MMC-3 SWABAUDIO BURNFREE Supported modes: TAO PACKET SAO SAO/R96R RAW/R96R Drive buf size : 1343488 = 1312 KB FIFO size : 12582912 = 12288 KB Speed set to 5645 KB/s 4 seconds. 3 seconds. 2 seconds. 1 seconds. 0 seconds. Operation starts. Waiting for reader process to fill input buffer ... input buffer ready. Performing OPC... Starting new track at sector: 0 Errno: 5 (Input/output error), write_g1 scsi sendcmd: no error CDB: 2A 00 00 00 35 E3 00 00 1F 00 status: 0x2 (CHECK CONDITION) Sense Bytes: 70 00 04 00 00 00 00 0A 00 00 00 00 08 03 00 00 Sense Key: 0x4 Hardware Error, Segment 0 Sense Code: 0x08 Qual 0x03 (logical unit communication crc error (ultra-dma/32)) Fru 0x0 Sense flags: Blk 0 (not valid) cmd finished after 0.026s timeout 40s wodim: A write error occured. wodim: Please properly read the error message above. write track data: error after 28252160 bytes Writing time: 22.643s Average write speed 238.9x. Min drive buffer fill was 100% Fixating... Fixating time: 22.904s BURN-Free was 1 times used. wodim: fifo had 637 puts and 446 gets. wodim: fifo was 0 times empty and 418 times full, min fill was 96%. == The problem is actually the == Errno: 5 (Input/output error), write_g1 scsi sendcmd: no error CDB: 2A 00 00 00 35 E3 00 00 1F 00 status: 0x2 (CHECK CONDITION) Sense Bytes: 70 00 04 00 00 00 00 0A 00 00 00 00 08 03 00 00 Sense Key: 0x4 Hardware Error, Segment 0 Sense Code: 0x08 Qual 0x03 (logical unit communication crc error (ultra-dma/32)) Fru 0x0 Sense flags: Blk 0 (not valid) cmd finished after 0.026s timeout 40s wodim: A write error occured. wodim: Please properly read the error message above. write track data: error after 28252160 bytes == It looks like a hardware error, as stated before by the log, but why? I am sure this is linked with the fact that it is done through IDE, but Windows does not complain about this. Thanks. - -- Merciadri Luca See http://www.student.montefiore.ulg.ac.be/~merciadri/ -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.4.9 (GNU/Linux) Comment: Processed by Mailcrypt 3.5.8 <http://mailcrypt.sourceforge.net/> iEYEARECAAYFAksjoJoACgkQM0LLzLt8MhzdlQCcC+7f6SK9mEf19Nf4pTLPjPwE kOMAnjkqYzR7wb0Bh8RACN4seWC5r8M+ =Gpi5 -----END PGP SIGNATURE----- -- To UNSUBSCRIBE, email to debian-user-requ...@lists.debian.org with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org