please don't top post! :-) Answer at the end:
Anand Sivaram wrote: > This is not a kernel bug, but the way debian uses drivers. There are > two different drivers in the kernel now. > Old ide drivers and newer pata drivers. Old ide drivers are going to > get deprecated. > For some reason debian stock kernel is taking only ide drivers. I > have seen this with both my desktop (ide amd74xx used, pata_amd is not > at all compiled) and laptop (both ide piix and pata ata_pii modules > are compiled, but ide piix used) > Because of that my hard drive is shown as /dev/hda instead of /dev/sda > with the debian stock kernel. > > What I did was to compile a custom kernel by including only the pata drivers. > Now with this custom kernel everything is fine and consistent. > > 2010/4/28 Γιώργος Πάλλας <gp...@ccf.auth.gr>: > >> Hi to everybody! >> >> I just got a WD caviar blue, with the classic IDE interface and tried to >> connect it to my debian squeeze pc which already has a WD SATA device, where >> the OS lives. >> >> The problem is that 2.6.32-3 does not recognize the disk and although I'm >> not an expert, I tend to think that it is a kernel bug. I booted with >> 2.6.30-2-686 and it sees the disk: >> [ 1.560374] hda: WDC WD3200AAJB-56R1A0, ATA DISK drive >> >> About the IDE controller, here's what lspci -v says: >> >> on both 2.6.30 and 2.6.32 : >> >> 00:14.1 IDE interface: ATI Technologies Inc SB600 IDE (prog-if 8a [Master >> SecP PriP]) >> Subsystem: Giga-byte Technology Gigabyte GA-MA69G-S3H Motherboard >> Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 16 >> I/O ports at 01f0 [size=8] >> I/O ports at 03f4 [size=1] >> I/O ports at 0170 [size=8] >> I/O ports at 0374 [size=1] >> I/O ports at f900 [size=16] >> Kernel driver in use: >> ATIIXP_IDE >> The only differences between lspci -v for 2.6.30 and 2.6.32 are the >> following: >> # diff 2.6.30-2-lspci 2.6.32-3-lspci >> 23c23 >> < Kernel driver in use: pcieport-driver >> --- >> >>> Kernel driver in use: pcieport >>> >> 38c38 >> < Kernel driver in use: pcieport-driver >> --- >> >>> Kernel driver in use: pcieport >>> >> 95d94 >> < Kernel driver in use: piix4_smbus >> >> where the pcieport differences refer to >> 00:02.0 PCI bridge: ATI Technologies Inc RD790 PCI to PCI bridge (external >> gfx0 port A) (prog-if 00 [Normal decode]) >> and >> 00:0a.0 PCI bridge: ATI Technologies Inc RD790 PCI to PCI bridge (PCI >> express gpp port F) (prog-if 00 [Normal decode]) >> >> The lshw utility shows almost perfect match between 2.6.30 and 2.6.32 with >> the difference that under the ide section which is identical in both >> kernels: >> >> *-ide >> description: IDE interface >> product: SB600 IDE >> vendor: ATI Technologies Inc >> physical id: 14.1 >> bus info: p...@0000:00:14.1 >> version: 00 >> width: 32 bits >> clock: 66MHz >> capabilities: ide bus_master >> configuration: driver=ATIIXP_IDE latency=32 >> resources: irq:16 ioport:1f0(size=8) ioport:3f6 >> ioport:170(size=8) ioport:376 ioport:f900(size=16) >> *-ide >> description: IDE Channel 0 >> physical id: 0 >> bus info: i...@0 >> logical name: ide0 >> clock: 66MHz >> >> but in 2.6.32 nothing disk relevant follows, where with 2.6.30, the disk >> section follows: >> >> *-disk >> description: ATA Disk >> product: WDC WD3200AAJB-56R1A0 >> vendor: Western Digital >> physical id: 0 >> bus info: i...@0.0 >> logical name: /dev/hda >> version: 01.03E01 >> serial: WD-WCAV2H175667 >> size: 298GiB (320GB) >> capabilities: ata dma lba iordy smart security pm >> partitioned partitioned:dos >> configuration: mode=udma5 signature=08040000 smart=on >> >> bit strange, isn't it? >> >> Any ideas? >> >> As well as that, I can't report it via reportbug, because with: reportbug >> linux-image-2.6.32-3-686 >> I always get >> >> Querying Debian BTS for reports on linux-2.6 (source)... >> Unable to connect to Debian BTS; continue [y|N|?]? >> >> after a couple of minutes... >> >> Giorgos That means that there is no way to get the disk working by using the stock kernel? It is also strange that the drivers are there in the 2.6.32, but they do not seem to work: [ 1.256871] atiixp 0000:00:14.1: IDE controller (0x1002:0x438c rev 0x00) [ 1.256894] ATIIXP_IDE 0000:00:14.1: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 1.256909] atiixp 0000:00:14.1: not 100% native mode: will probe irqs later [ 1.256915] ide0: BM-DMA at 0xf900-0xf907 [ 1.256923] Probing IDE interface ide0... [ 1.265866] ide0: no devices on the port Any kernel expert to explain what exactly is happening here?
smime.p7s
Description: S/MIME Cryptographic Signature
