From the link that you so handily provided in your OP:
Configuring libtrash
Oddly enough, before you install libtrash, you must configure it. The
libtrash-1.8/libtrash.conf file comes preconfigured with default
settings. When libtrash is compiled, the /etc/libtrash.conf file is
created, but this file only reflects the default configuration of libtrash.
That doesn’t mean you can’t reconfigure libtrash. It just takes a little
extra work. There are two configurations available when libtrash is
activated:
* Systemwide configuration: This is used for all users. This
configuration is read from the /etc/libtrash.conf file.
* Personal configurations: Each user may use a separate
configuration. Separate configurations are enabled through settings read
from the .libtrash file in the home directory of each user.
Systemwide configuration
Systemwide settings are made through the /etc/libtrash.conf file. The
required settings must be made prior to compiling libtrash. Changing the
/etc/libtrash.conf file after compiling libtrash will not change the
default behavior of the program. To enforce the idea that this file
should never be edited, no users are given write permission to this
file. The /etc/libtrash.conf file is a read-only file for all users,
including root. Therefore, you’ll make changes to the
libtrash-1.8/libtrash.conf file prior to installation.
There are four entries in the libtrash.conf that are used as
environmental variables and cannot be changed by a user's personal
configuration settings when libtrash is run. These four settings are:
* DEBUG
* PERSONAL_CONF_FILE
* WARNING_STRING
* UNCOVER_DIRS
The next four settings allow libtrash to intercept the standard routines
Linux uses when files are unlinked or renamed. Your safest bet is to use
the defaults for all of these settings:
* INTERCEPT_UNLINK= YES
* INTERCEPT_RENAME = YES
* INTERCEPT_FOPEN
* INTERCEPT_OPEN
More options, more control
The rest of options give you more control over libtrash. These options are:
* TRASH_CAN = Trash
This entry sets the name for the subdirectory where deleted files
will be stored. The default name for this directory is Trash. Any name
may be used. To change the directory name, enter the new name without
any slashes.
* IN_CASE_OF- FAILURE =
This setting determines how libtrash reacts when there is a
failure. Setting this value to PROTECT prevents files from being deleted
by the standard Linux function. Setting the value to ALLOW_DESTRUCTION
overrides libtrash.
* SHOULD-WARN = YES
This setting enables a warning message for libtrash. It's
normally a good idea to remind users that their files will be
permanently deleted when libtrash is disabled. This is especially true
if users on the system are new to Linux or for users who assume libtrash
is always running.
* PROTECT_TRASH = YES
This setting protects files in the trash from being deleted.
Files placed in the user's trash represent a special case. Libtrash
functions by sending deleted files to a trashcan in the user's home
directory. When the user wants to delete files in the trashcan, the
default libtrash doesn't work.
* IGNORE_ENTENSIONS =
This setting allows you to specify files with specific extensions
that may be deleted without being copied to the trashcan. To specify
which types may be ignored by libtrash, create a semicolon delimited
separated list of the file extensions to be ignored. Do not include a
dot (.) before the extension. For example, to allow .o, .c, and log
files to be deleted without being moved to the trashcan, use this entry:
IGNORE_ENTENSIONS = o; c; log
* IGNORE_HIDDEN = YES
Hidden files and files inside hidden directories may be sent to
the trash. Setting this entry to YES allows Linux to delete hidden files
without moving them to the trash. Stick with the default value of YES
and override it if you must on a per-user basis.
* IGNORE_EDITOR_BACKUP = NO
This entry will ensure that backups of important files are always
sent to the trash. These are files that end with a tilde (~). The
default is yes. Changing this setting might be a good idea.
* IGNORE-EDITOR-TEMPORARY = YES
This entry concerns temporary files created by editors. Setting
this entry to YES allows these temporary files to be removed without
moving them to the trash. Set the entry to NO to allow libtrash to move
these files to the user's trash. Stick with the default and change this
setting on a per-user basis.
* LIBTRASH_CONFIG_FILE_UNREMOVEABLE = YES
This entry provides protection for the user's personal libtrash
configuration file. Removing your own configuration file will cause
unexpected actions from libtrash. Leave this setting alone.
* TRASH_SYSTEM_ROOT
The TRASH_SYSTEM_ROOT variable specifies the location of the
directory under the trash that will function as the root (/) of the file
system whenever the GLOBAL_PROTECTION variable is set to YES. If global
protection is not used, this variable is ignored. This variable always
uses a directory name with no slashes. The default setting is
TRASH_SYSTEM-ROOT = SYSTEM_ROOT.
* UNREMOVEABLE_DIRS=/bin;/boot;/dev;/etc;/lib;/sbin;/usr
Any directory on the system can be marked as an unremoveable
directory. All files in these directories are protected from deletion by
any user running libtrash. This may be the most important step in the
entire libtrash configuration process. By carefully establishing a list
of protected directories, the administrator can prevent users from
either accidentally or intentionally removing critical directories and
files. The default list is a commented line in the /libtrash.conf file.
To activate this list, remove the comment (#) from the beginning of the
line. To add additional directories, add a semicolon to the end of the
line, and then add the path to the directory you want protected. In the
example, the directory /usr/local/users has been added to the default
entry to protected programs.
* UNCOVER_DIRS =
Any directories listed as unremoveable may be temporarily removed
from the above list by adding the directory to the UNCOVER_DIRS list.
The default list is empty. Leave it empty. Any files that need to be
uncovered should be added to an UNCOVER_DIRS list in the user's personal
configuration file. This prevents all users from being able to remove
specified directories.
* USER_TEMPORATY_DIRS = temp
The USER_TEMPORARY_DIRS entry specifies a directory or list of
directories under the user's home directory where temporary files are
created. Files in these directories are always permanently deleted.
Leave this setting if you don't require this feature.
* REMOVEABLE_MEDIA_NMOUNT_POINTS
This setting prevents copies of removeable media from being
copied to the trashcan when global protection is used. The
REMOVEABLE_MEDIA_NMOUNT_POINTS setting is activated by default. This
setting is ignored when global protection is disabled.
* EXCEPTIONS
The EXCEPTIONS setting is used to remove protection from files
normally considered unremoveable. This allows essential actions by
programs, such as creating or deleting a lock file or
mounting/unmounting a drive, and may require some files in the
UNREMOVEABLE_DIRS setting to be created and deleted. The default entry
is EXCEPTIONS = /etc/mtab; /etc/resolv.conf; /etc/adjtime; /etc/upsstatus
Study these entries, and consider your system requirements. Once the
configuration settings are entered, the next step is to compile and
install libtrash.
Creating a personal configuration file
Personal configurations are created in each user's home directory. These
settings are identical to the ones in the libtrash.conf file mentioned
above, and, unless stated above, you should override the settings. For
example, you could create the file ~/.libtrash in your home directory
with these entries:
* GLOBAL_PROTECTION = NO
* IGNORE EXTENSIONS = bat; exe;com
These entries disable global protection, and allow any files with the
extension bat, exe, or com to be permanently deleted without moving them
to the trash.
On multiuser systems, the administrator will probably want all users or
groups of users to be able to use libtrash. On these systems, the root
user should create a standard libtrash configuration for each group of
users requiring a predefined configuration.
On 04/24/2011 05:54 PM, Jason Hsu wrote:
The files that I deleted or removed with "rm" didn't show up in the Trash
folder. I tried adding those commands to the /etc/profile file and the
/home/(username)/.bashrc files, but that didn't work.
What's the proper way to configure libtrash? Is it working on your computer? When you
delete a file in the GUI or remove it with the "rm" command, does it show up in
your Trash folder?
On Sun, 24 Apr 2011 17:41:52 -0500
Ron Johnson<ron.l.john...@cox.net> wrote:
Define "didn't work". Returned an error message?
Adding that code to /home/(username)/.bashrc didn't work either.
Has ANYONE successfully implemented libtrash?
Did you configure it properly?
--
"Neither the wisest constitution nor the wisest laws will secure
the liberty and happiness of a people whose manners are universally
corrupt."
Samuel Adams, essay in The Public Advertiser, 1749
--
To UNSUBSCRIBE, email to debian-user-requ...@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org
Archive: http://lists.debian.org/4db4b707.3090...@cox.net