On Sun, 2012-05-06 at 13:51 +0900, Osamu Aoki wrote: > Hi, > > On Sat, May 05, 2012 at 01:24:59AM +0200, Steven Post wrote: > > Hello list, > > > > I'm testing out a new system, the idea is to combine 6 hard drives into > > a single btrfs volume (raid10) (using subvolumes for /, /home, etc). I > > understand that it is now possible to also have /boot on btrfs > > (previously impossible because of GRUB). > > I tried to install sysyem with much simpler configuration: > / : a single btrfs on a partition /dev/sda1 > swap: a single swap on a separate partition /dev/sda2 > > It did not work due to missing fsck.btrfs in btrfs-tools. > http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=668832 > http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=567681
I've had the same problem, but I was aware of it from an earlier attempt using virtualbox and a separate ext4 /boot partition. This can be solved by changing /etc/fstab (booting from a live cd), look for the line with the btrfs system, then change last number on that line to a '0' (the 'pass' column). > > > Unfortunately the Debian installer (daily build for wheezy) is unable to > > create multi-device btrfs volumes. > > Yah.. but you probably can do this via shell screen. I don't think I'm able to do that from the rescue mode shell without using an existing installation, without the existing installation I get a 'Command not found' error on 'btrfs device scan', I assume this includes the whole btrfs command. > > > I tried the a normal install and then copy it over to a multi-device > > btrfs system, afterwards adding the remaining disk: > > 1) using a single drive to install using ext4 for /boot and btrfs for / > > 2) after (successful) installation boot from a live cd (ubuntu 12.04 in > > this case, but it shouldn't really matter) > > How successful? Did it boot? It boots, yes, but you still need to change /etc/fstab using a live cd because of the missing fsck tool. > > > 3) create partitions for btrfs on the other 5 drives using gdisk > > 4) create a multi-device btrfs filesystem with those partitions, with a > > subvolume for the root filesystem and for /home > > 5) copy all the data from the first disk to the new btrfs volume > > 6) chroot into the rootfs of the new volume, after mounting (-o > > bind) /dev, /proc and /sys into the mounted system > > 7) change fstab for the new drives and modify /etc/default/grub > > 8) run update-grub: this is where things start falling down, I get an > > error about / not being mounted so grub fails. > > > > This is apparently caused by a regression in GRUB [1] (Debian bug > > #538118). > > Well this is possibly another problem you are facing. Basically, you > should know what file to change imanually when copying files from one > partition to another. So this is really an expert trick which d-i > currently does not support for ordinry uses. But as I mention in the > above, most simple installation suffer major breakage for btrfs on > wheezy even if you manually adjust configuration files. > I'll have another look if my other attempts from within the d-i fails. Another thing I noticed during my tests is that the installer will recognize existing btrfs partitions and is able to use them, except when dealing with a multi-device file system. Using rescue mode you can trick d-i into using them properly by executing a shel in an existing installation, then issuing a btrfs device scan. Once the scan is done, you can exit the shell and go back to the partitioner. There I could select a device (partition) from the btrfs system and use it as /, now the mount works with the multi-device partition. Perhaps d-i should issue the 'btrfs device scan' command when starting the partitioner? Kind regards, Steven
signature.asc
Description: This is a digitally signed message part