I'm running wheezy and recently added a new graphics card (nvidia 980 Ti) and a new monitor (Dell 3440x1440 resolution). The connection is via DisplayPort. I would like to get this to work, though I don't necessarily need a lot of acceleration. At the moment the best I can do is 1024x768 (method 1 below), and most things (methods 2 and 3) produce a blank monitor. I'm also having some weird BIOS behavior (point 5 below).
Any advice about the best way to proceed? Should I be trying to make the vesa driver (if that's what I'm using) work by filling in modelines in xorg.conf? I'd have to make up a lot of the info they call for. Or perhaps I should try to manually build the driver from nvidia? But I suspect that may not work with the wheezy kernel. DETAILS 1. [Vanilla autodetect] X appears unable to get useful info from the monitor. It mentions the nouveau driver (which mentions specific device ids, none of which match my card), but the active section seems to be after [ 127.155] (II) VESA: driver for VESA chipsets: vesa [ 127.155] (II) FBDEV: driver for framebuffer: fbdev It assumes default sync and refresh rates, which don't line up well with the monitor specs. After several attempts it says [ 127.731] (WW) VESA(0): No valid modes left. Trying less strict filter... [ 127.731] (II) VESA(0): <default monitor>: Using hsync range of 31.50-48.00 kHz [ 127.731] (II) VESA(0): <default monitor>: Using vrefresh range of 50.00-70.00 Hz [ 127.731] (II) VESA(0): <default monitor>: Using maximum pixel clock of 65.00 MHz [ 127.731] (WW) VESA(0): Unable to estimate virtual size [ 127.731] (II) VESA(0): Not using built-in mode "1600x1200" (hsync out of range) [ 127.731] (II) VESA(0): Not using built-in mode "1280x1024" (hsync out of range) [ 127.731] (II) VESA(0): Not using built-in mode "1280x800" (hsync out of range) [ 127.731] (II) VESA(0): Not using built-in mode "640x400" (hsync out of range) [ 127.731] (II) VESA(0): Not using built-in mode "320x400" (hsync out of range) [ 127.731] (II) VESA(0): Not using built-in mode "320x240" (illegal horizontal timings) [ 127.731] (II) VESA(0): Not using built-in mode "320x200" (illegal horizontal timings) [ 127.731] (--) VESA(0): Virtual size is 1024x768 (pitch 1024) [ 127.731] (**) VESA(0): *Built-in mode "1024x768" [ 127.731] (**) VESA(0): *Built-in mode "800x600" [ 127.731] (**) VESA(0): *Built-in mode "640x480" [ 127.731] (==) VESA(0): DPI set to (96, 96) 2. [nVidia proprietary packed for Wheezy] I tried the proprietary driver following the instructions for https://wiki.debian.org/NvidiaGraphicsDrivers#Version_340.65_.28via_wheezy-backports.29 However, this produced a blank screen and the log showed the driver didn't recognize the card. I belatedly checked the list of supported cards, and mine wasn't on it (though the 980Ti is on https://wiki.debian.org/NvidiaGraphicsDrivers#Version_352.55_64bit_.28nvidia_site_installer.29 for Jessie/sid). So I purged everything from that step. 3. [nouveau in wheezy] I modified the xorg.conf that the nvidia utility produced in 2. so that it used the nouveau driver. I added the physical dimensions of the monitor and the refresh and sync rates from the monitor specs, but no specific resolutions. This produced a blank screen. I had thought 1. was using nouveau, but not I think it wasn't. I'd guess the nouveau driver is tied to specific device id's, and doesn't recognize newer hardware. BTW, the info I provided was Section "Monitor" Identifier "Monitor0" VendorName "Dell" ModelName "U3415W" HorizSync 30 - 89 VertRefresh 48 - 85 DisplaySize 798.20 334.80 Option "DPMS" EndSection The manual provides specific resolution and frequency combinations, though not anything that looks to me like syncstart or syncend values. 4. Dell's site doesn't seem to have an edid file for the monitor; some net resources mentioned using one if it was available. I downloaded their drivers on windows and expanded them to check. 5. I tried to install a fresh jessie system in some unused space, but I can't get into my BIOS to get it boot off USB. The BIOS setting for virtualization seems to have mysteriously turned off too. I realize I could run debootstrap, but since I'm not ready to migrate for real that seems a lot of work. Thanks. Ross Boylan
