Based on the discussion under Declude JM, I'm also looking at adding invURIBL. However, I find the weighting system in the invurible.exe.config file very confusing. This is the total weight passed to Declude? I can't figure out what typical weight scores would be or how to adjust them.
Just for reference, we mark the subject line at 5, divert the messages into a separate folder at 10, and delete at 15 using Sniffer and Declude JM. Thanks, Ben ----- Original Message ----- From: "Kevin Bilbee" <[EMAIL PROTECTED]> To: <Declude.JunkMail@declude.com> Sent: Friday, April 07, 2006 9:34 AM Subject: RE: [Declude.JunkMail] invURIBL > I adjusted the weights to match my weight ranges > > INV-URIBL external weight "D:\IMail\declude\INVURIBL2.7\INVURIBL.exe > %WEIGHT% %REMOTEIP%" 0 0 > > The weights are assigned in the INVURIBL.exe.config not in declude's > GLOBAL.CFG > > Just look at each test and read the web site. Determine what will work for > your weigting system. Then adjust based on your false positive rate. > > > Kevin Bilbee > > > > > -----Original Message----- > > From: [EMAIL PROTECTED] > > [mailto:[EMAIL PROTECTED] Behalf Of Craig Edmonds > > Sent: Friday, April 07, 2006 8:46 AM > > To: Declude.JunkMail@declude.com > > Subject: RE: [Declude.JunkMail] invURIBL > > Importance: High > > > > > > Kevin, > > > > What weight did you give? > > > > Kindest Regards > > Craig Edmonds > > 123 Marbella Internet > > W: www.123marbella.com > > > > > > > > -----Original Message----- > > From: [EMAIL PROTECTED] > > [mailto:[EMAIL PROTECTED] On Behalf Of Kevin Bilbee > > Sent: Friday, April 07, 2006 5:35 PM > > To: Declude.JunkMail@declude.com > > Subject: RE: [Declude.JunkMail] invURIBL > > > > We had to change the DNS timeout. > > > > > > Kevin Bilbee > > > > > -----Original Message----- > > > From: [EMAIL PROTECTED] > > > [mailto:[EMAIL PROTECTED] On Behalf Of Todd Richards > > > Sent: Friday, April 07, 2006 8:18 AM > > > To: Declude.JunkMail@declude.com > > > Subject: [Declude.JunkMail] invURIBL > > > > > > > > > Per suggestions from others, I am looking to implement invURIBL on our > > > mail server (Imail 8.2x with Declude 4.0.9). > > > I wanted to give it a trial run first, but because of it's low cost > > > and recommendations from others, I will probably just implement it. > > > > > > I'm not much of a tweaker so I'm curious if anyone has any "must > > > tweaks" after installation, or any other recommendations for settings. > > > > > > Thanks for any tips. > > > > > > Todd > > > > > > > > > --- > > > This E-mail came from the Declude.JunkMail mailing list. To > > > unsubscribe, just send an E-mail to [EMAIL PROTECTED], and type > > > "unsubscribe Declude.JunkMail". The archives can be found at > > > http://www.mail-archive.com. > > > > > > > --- > > This E-mail came from the Declude.JunkMail mailing list. To unsubscribe, > > just send an E-mail to [EMAIL PROTECTED], and type "unsubscribe > > Declude.JunkMail". The archives can be found at > > http://www.mail-archive.com. > > [ This E-mail has been scanned for Spam and Viruses by Declude ] > > [ Thank You > > For Using 123 Marbella Internet ] > > > > > > > > > > [ This E-mail has been scanned for Spam and Viruses by Declude ] > > [ Thank You For Using 123 Marbella Internet ] > > > > --- > > This E-mail came from the Declude.JunkMail mailing list. To > > unsubscribe, just send an E-mail to [EMAIL PROTECTED], and > > type "unsubscribe Declude.JunkMail". The archives can be found > > at http://www.mail-archive.com. > > > > --- > This E-mail came from the Declude.JunkMail mailing list. To > unsubscribe, just send an E-mail to [EMAIL PROTECTED], and > type "unsubscribe Declude.JunkMail". The archives can be found > at http://www.mail-archive.com. > --- This E-mail came from the Declude.JunkMail mailing list. To unsubscribe, just send an E-mail to [EMAIL PROTECTED], and type "unsubscribe Declude.JunkMail". The archives can be found at http://www.mail-archive.com.