No we can add or remove only one vlan range at a time. On Apr 24, 2013, at 10:50 AM, Radhika Puthiyetath <radhika.puthiyet...@citrix.com> wrote:
> Can I add/ remove multiple vlan ranges ( vlan 500- 600, 200- 250; remove 100- > 150, 300-350) by using the API? > > -----Original Message----- > From: Bharat Kumar [mailto:bharat.ku...@citrix.com] > Sent: Thursday, March 14, 2013 1:55 PM > To: cloudstack-...@incubator.apache.org > Subject: Re: [Discuss] Support for non-contiguous vlan ranges. > > If the remove fails add will also fail. > > Bharat. > On Mar 13, 2013, at 11:26 AM, Chiradeep Vittal <chiradeep.vit...@citrix.com> > wrote: > >> If the remove fails, will the add still succeed? >> >> On 3/5/13 11:20 PM, "Bharat Kumar" <bharat.ku...@citrix.com> wrote: >> >>> The changes will be atomic. >>> before removing any range we need to check if any of the vlans in the >>> range are in use. The operation will fail if some vlans in the remove >>> range are in use. >>> i.e. if E=100-200 (existing) U(used)=101,121,131 and remove=100-201 >>> we do not remove this range as 101,121, and 131 are being used. >>> if the admin wants to remove the reset of the range leaving the used >>> ones he can say remove 100-100, 102-120, etc >>> >>> I will update this in the FS. >>> >>> Bharat. >>> >>> On Mar 6, 2013, at 6:11 AM, Chiradeep Vittal >>> <chiradeep.vit...@citrix.com> wrote: >>> >>>> Will the changes be atomic? All or nothing? >>>> >>>> Existing range E= 100-200, in use U=101,121,131 New request: >>>> add=201-301, remove=100-201 >>>> >>>> Or >>>> E = 100-200, U=110-120 >>>> A = 150-250, R=100-149 >>>> >>>> etc >>>> >>>> On 1/24/13 10:13 PM, "Bharat Kumar" <bharat.ku...@citrix.com> wrote: >>>> >>>>> Thank you Manan for pointing this out i intended to say multiple >>>>> Vlans not IPs. >>>>> I corrected it in the FS. >>>>> >>>>> Bharat >>>>> On Jan 25, 2013, at 4:25 AM, Manan Shah <manan.s...@citrix.com> wrote: >>>>> >>>>>> Bharat, I reviewed the FS and I have the following question. It >>>>>> states thatÅ >>>>>> >>>>>> Admin can update the vlan range after creation or can add multiple >>>>>> non contiguous vlan ranges while creating a zone. This can be done >>>>>> by changing the UpdatephysicalNetwork api. It allows only >>>>>> extending of the vlan. we plan to extend the api to update the >>>>>> vlan with multiple ip Ranges. >>>>>> >>>>>> What does it mean by "we plan to extend the API to update the VLAN >>>>>> with multiple IP Ranges". Specifically the "Multiple IP Ranges" >>>>>> part. >>>>>> >>>>>> Can you clarify? >>>>>> >>>>>> >>>>>> Regards, >>>>>> Manan Shah >>>>>> >>>>>> >>>>>> >>>>>> >>>>>> On 1/4/13 8:49 AM, "Manan Shah" <manan.s...@citrix.com> wrote: >>>>>> >>>>>>> Bharat, I have created a JIRA ticket as well as requirements page >>>>>>> for this requirement. Please leverage that. >>>>>>> >>>>>>> Regards, >>>>>>> Manan Shah >>>>>>> >>>>>>> >>>>>>> >>>>>>> >>>>>>> On 1/3/13 10:33 PM, "Prasanna Santhanam" <t...@apache.org> wrote: >>>>>>> >>>>>>>> On Fri, Jan 04, 2013 at 11:37:28AM +0530, Bharat Kumar wrote: >>>>>>>>> Hi all, >>>>>>>>> >>>>>>>>> In cloudstack we specify the vlan ranges in advanced zone. >>>>>>>>> These vlans are used while creating the guest networks. >>>>>>>>> Presently we can add only one continuos vlan range. There is no >>>>>>>>> way to add non contiguous vlan ranges. >>>>>>>>> >>>>>>>>> So we propose to add a feature to support adding multiple vlan >>>>>>>>> ranges. >>>>>>>>> >>>>>>>>> This feature will enable adding non contiguous vlan ranges. >>>>>>>>> >>>>>>>> >>>>>>>> Will it support extending the ranges in non-contiguous >>>>>>>> increments after the zone has been created? >>>>>>>> >>>>>>>> So I start with 100-200 and then later extend my switch and >>>>>>>> cloudstack to do 300-400, 492 and 50-80 say? >>>>>>>> >>>>>>>> -- >>>>>>>> Prasanna., >>>>>>> >>>>>> >>>>> >>>> >>> >> >