Added info in testpmd functions section for the following commands: - tunnel_filter add - tunnel_filter rm - rx_vxlan_port add - rx_vxlan_port rm - port stop/start queue - set port mac address filter (for VF) - tx_checksum set - tso set - tso show
Signed-off-by: Pablo de Lara <pablo.de.lara.guarch at intel.com> --- doc/guides/testpmd_app_ug/testpmd_funcs.rst | 79 +++++++++++++++++++++++++++ 1 files changed, 79 insertions(+), 0 deletions(-) diff --git a/doc/guides/testpmd_app_ug/testpmd_funcs.rst b/doc/guides/testpmd_app_ug/testpmd_funcs.rst index 5e62ff9..c010577 100644 --- a/doc/guides/testpmd_app_ug/testpmd_funcs.rst +++ b/doc/guides/testpmd_app_ug/testpmd_funcs.rst @@ -150,6 +150,15 @@ For example: filter on qinq(extend) off +show port rss reta +~~~~~~~~~~~~~~~~~~ + +Display the rss redirection table entry indicated by masks on port X: + +show port (port_id) rss reta (size) (mask0, mask1...) + +size is used to indicate the hardware supported reta size + show port rss-hash ~~~~~~~~~~~~~~~~~~ @@ -456,6 +465,36 @@ Set the outer VLAN TPID for packet filtering on a port: rx_vlan set tpid (value) (port_id) +tunnel_filter add +~~~~~~~~~~~~~~~~~ + +Add a tunnel filter on a port: + +tunnel_filter add (port_id) (outer_mac) (inner_mac) (ip_addr) (inner_vlan) + (tunnel_type) (filter_type) (tenant_id) (queue_id) + +tunnel_filter remove +~~~~~~~~~~~~~~~~~~~~ + +Remove a tunnel filter on a port: + +tunnel_filter rm (port_id) (outer_mac) (inner_mac) (ip_addr) (inner_vlan) + (tunnel_type) (filter_type) (tenant_id) (queue_id) + +rx_vxlan_port add +~~~~~~~~~~~~~~~~~ + +Add an UDP port for VXLAN packet filter on a port: + +rx_vxlan_port add (udp_port) (port_id) + +rx_vxlan_port remove +~~~~~~~~~~~~~~~~~~~~ + +Remove an UDP port for VXLAN packet filter on a port: + +rx_vxlan_port rm (udp_port) (port_id) + tx_vlan set ~~~~~~~~~~~ @@ -498,6 +537,29 @@ bit 3 - if set insert sctp checksum offload Check the NIC Datasheet for hardware limits. +tx_checksum show +~~~~~~~~~~~~~~~~ + +Display tx checksum offload configuration: + +tx_checksum show (port_id) + +tso set +~~~~~~~ + +Enable TCP Segmentation Offload in csum forward engine: + +tso set (segsize) (port_id) + +.. note:: + Please check the NIC datasheet for HW limits + +tso show +~~~~~~~~ + +Display the status of TCP Segmentation Offload: + +tso show (port_id) set fwd ~~~~~~~ @@ -635,6 +697,14 @@ Set VF receive/transmit from a port: set port (port_id) vf (vf_id) (rx|tx) (on|off) +set port - mac address filter (for VF) +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ + +Add/Remove unicast or multicast MAC addr filter for a VF: + +set port (port_id) vf (vf_id) (mac_addr) + (exact-mac|exact-mac-vlan|hashmac|hashmac-vlan) (on|off) + set port - rx mode(for VF) ~~~~~~~~~~~~~~~~~~~~~~~~~~ @@ -1061,6 +1131,15 @@ Close all ports or a specific port: port close (port_id|all) +port start/stop queue +~~~~~~~~~~~~~~~~~~~~~ + +Start/stop a rx/tx queue on a specific port: + +port (port_id) (rxq|txq) (queue_id) (start|stop) + +Only take effect when port is started. + port config - speed ~~~~~~~~~~~~~~~~~~~ -- 1.7.4.1