on XL710, performance number is far from the expectation on recent firmware versions, if promiscuous mode is disabled, or promiscuous mode is enabled and port MAC address is equal to the packet destination MAC address. The fix for this issue may not be integrated in the following firmware version. So the workaround in software driver is needed. It needs to modify the initial values of 2 internal only registers which is the same 2 of 3 registers of it did for X710. Note that the workaround can be removed when it is fixed in firmware in the future.
Signed-off-by: Helin Zhang <helin.zhang at intel.com> --- lib/librte_pmd_i40e/i40e_ethdev.c | 35 ++++++++++++++++++++++------------- 1 file changed, 22 insertions(+), 13 deletions(-) diff --git a/lib/librte_pmd_i40e/i40e_ethdev.c b/lib/librte_pmd_i40e/i40e_ethdev.c index b47a3d2..3bb75d8 100644 --- a/lib/librte_pmd_i40e/i40e_ethdev.c +++ b/lib/librte_pmd_i40e/i40e_ethdev.c @@ -5327,21 +5327,30 @@ i40e_debug_read_register(struct i40e_hw *hw, uint32_t addr, uint64_t *val) /* * On X710, performance number is far from the expectation on recent firmware - * versions. The fix for this issue may not be integrated in the following + * versions; on XL710, performance number is also far from the expectation on + * recent firmware versions, if promiscuous mode is disabled, or promiscuous + * mode is enabled and port MAC address is equal to the packet destination MAC + * address. The fix for this issue may not be integrated in the following * firmware version. So the workaround in software driver is needed. It needs - * to modify the initial values of 3 internal only registers. Note that the - * workaround can be removed when it is fixed in firmware in the future. + * to modify the initial values of 3 internal only registers for X710, and the + * same 2 internal registers for XL710. Note that the workaround can be removed + * when it is fixed in firmware in the future. */ -static void -i40e_configure_registers(struct i40e_hw *hw) -{ -#define I40E_GL_SWR_PRI_JOIN_MAP_0 0x26CE00 -#define I40E_GL_SWR_PRI_JOIN_MAP_2 0x26CE08 -#define I40E_GL_SWR_PM_UP_THR 0x269FBC + +/* For both X710 and XL710 */ #define I40E_GL_SWR_PRI_JOIN_MAP_0_VALUE 0x10000200 +#define I40E_GL_SWR_PRI_JOIN_MAP_0 0x26CE00 + #define I40E_GL_SWR_PRI_JOIN_MAP_2_VALUE 0x011f0200 +#define I40E_GL_SWR_PRI_JOIN_MAP_2 0x26CE08 + +/* For X710 only */ #define I40E_GL_SWR_PM_UP_THR_VALUE 0x03030303 +#define I40E_GL_SWR_PM_UP_THR 0x269FBC +static void +i40e_configure_registers(struct i40e_hw *hw) +{ static const struct { uint32_t addr; uint64_t val; @@ -5354,11 +5363,11 @@ i40e_configure_registers(struct i40e_hw *hw) uint32_t i; int ret; - /* Below fix is for X710 only */ - if (i40e_is_40G_device(hw->device_id)) - return; - for (i = 0; i < RTE_DIM(reg_table); i++) { + if ((i40e_is_40G_device(hw->device_id)) && + (reg_table[i].addr == I40E_GL_SWR_PM_UP_THR)) + continue; + ret = i40e_debug_read_register(hw, reg_table[i].addr, ®); if (ret < 0) { PMD_DRV_LOG(ERR, "Failed to read from 0x%"PRIx32, -- 1.9.3