Hi, Meunier, Julien
> -----Original Message-----
> From: dev [mailto:dev-boun...@dpdk.org] On Behalf Of Meunier, Julien
> (Nokia - FR/Paris-Saclay)
> Sent: Monday, January 7, 2019 11:53 PM
> To: Zhang, Qi Z <qi.z.zh...@intel.com>; Ananyev, Konstantin
> <konstantin.anan...@intel.com>; Lu, Wenzhuo <wenzhuo...@intel.com>
> Cc: dev@dpdk.org
> Subject: Re: [dpdk-dev] [PATCH] net/ixgbe: add support of loopback for
> X540/X550
>
> Hi,
>
> Mmm, you're right. However, as like for the 82599, the pmd skips the link
> configuration, so, it should not enable the autoneg.
>
> During my tests, I had a 10G connectivity, and I didn't notice any problem. I
> used the DPDK application "test", with the test pmd_perf_autotest.
It seems you are right, autoneg is done in function of
ixgbe_setup_link()->........ ()
which call function ixgbe_setup_phy_link_speed_generic()->ixgbe_setup_phy_link
()->
ixgbe_setup_phy_link_generic (), do the work for Auto-Negotiation, but pmd
code skip it.
But the bit C of Address 7.0 is initialized as 1 by default in datasheet, what
pmd code skip is just the
Process of Auto-Negotiation, because we skip code of bellow In
ixgbe_setup_phy_link_generic (), not disable bit 7.0.c.
So, you had better disable 7.0.c bit when mac loopback is enable.
"
/* Restart PHY auto-negotiation. */
hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_CONTROL,
IXGBE_MDIO_AUTO_NEG_DEV_TYPE, &autoneg_reg);
autoneg_reg |= IXGBE_MII_RESTART;
hw->phy.ops.write_reg(hw, IXGBE_MDIO_AUTO_NEG_CONTROL,
IXGBE_MDIO_AUTO_NEG_DEV_TYPE, autoneg_reg);
"
>
> Should I need to modify my code to be sure that autoneg is disabled (and
> force it to 10G) ?
>
> Thanks,
> Best regards,
> Julien Meunier
>
> On 07/01/2019 07:53, Zhang, Qi Z wrote:
> >
> >
> >> -----Original Message-----
> >> From: dev [mailto:dev-boun...@dpdk.org] On Behalf Of Julien Meunier
> >> Sent: Thursday, January 3, 2019 12:01 AM
> >> To: Ananyev, Konstantin <konstantin.anan...@intel.com>; Lu, Wenzhuo
> >> <wenzhuo...@intel.com>
> >> Cc: dev@dpdk.org
> >> Subject: [dpdk-dev] [PATCH] net/ixgbe: add support of loopback for
> >> X540/X550
> >>
> >> Loopback mode is also supported on X540 and X550 NICs, according to
> >> their datasheet (section 15.2). The way to set it up is a little different
> >> of
> the 82599.
> >
> > Thanks for enable this.
> >
> > one question is, Datasheet also mentioned that auto negotiation should
> > be disabled but I didn't see any related change with it.
> >
> > Would you share more insight on this?
> >
> >>
> >> Signed-off-by: Julien Meunier <julien.meun...@nokia.com>
> >> ---
> >> drivers/net/ixgbe/ixgbe_ethdev.c | 10 ++++++---
> >> drivers/net/ixgbe/ixgbe_ethdev.h | 5 ++---
> >> drivers/net/ixgbe/ixgbe_rxtx.c | 47
> >> ++++++++++++++++++++++++++++++++++------
> >> 3 files changed, 49 insertions(+), 13 deletions(-)
> >>
> >> diff --git a/drivers/net/ixgbe/ixgbe_ethdev.c
> >> b/drivers/net/ixgbe/ixgbe_ethdev.c
> >> index 7493110..7eb3303 100644
> >> --- a/drivers/net/ixgbe/ixgbe_ethdev.c
> >> +++ b/drivers/net/ixgbe/ixgbe_ethdev.c
> >> @@ -2652,9 +2652,13 @@ ixgbe_dev_start(struct rte_eth_dev *dev)
> >> goto error;
> >> }
> >>
> >> - /* Skip link setup if loopback mode is enabled for 82599. */
> >> - if (hw->mac.type == ixgbe_mac_82599EB &&
> >> - dev->data->dev_conf.lpbk_mode ==
> IXGBE_LPBK_82599_TX_RX)
> >> + /* Skip link setup if loopback mode is enabled. */
> >> + if ((hw->mac.type == ixgbe_mac_82599EB ||
> >> + hw->mac.type == ixgbe_mac_X540 ||
> >> + hw->mac.type == ixgbe_mac_X550 ||
> >> + hw->mac.type == ixgbe_mac_X550EM_x ||
> >> + hw->mac.type == ixgbe_mac_X550EM_a) &&
> >> + dev->data->dev_conf.lpbk_mode ==
> IXGBE_LPBK_TX_RX)
> >> goto skip_link_setup;
> >>
> >> if (ixgbe_is_sfp(hw) && hw->phy.multispeed_fiber) { diff --git
> >> a/drivers/net/ixgbe/ixgbe_ethdev.h
> b/drivers/net/ixgbe/ixgbe_ethdev.h
> >> index 565c69c..c60a697 100644
> >> --- a/drivers/net/ixgbe/ixgbe_ethdev.h
> >> +++ b/drivers/net/ixgbe/ixgbe_ethdev.h
> >> @@ -65,9 +65,8 @@
> >> #define IXGBE_QUEUE_ITR_INTERVAL_DEFAULT 500 /* 500us */
> >>
> >> /* Loopback operation modes */
> >> -/* 82599 specific loopback operation types */
> >> -#define IXGBE_LPBK_82599_NONE 0x0 /* Default value. Loopback is
> disabled.
> >> */
> >> -#define IXGBE_LPBK_82599_TX_RX 0x1 /* Tx->Rx loopback operation is
> >> enabled. */
> >> +#define IXGBE_LPBK_NONE 0x0 /* Default value. Loopback is disabled.
> */
> >> +#define IXGBE_LPBK_TX_RX 0x1 /* Tx->Rx loopback operation is
> enabled.
> >> +*/
> >>
> >> #define IXGBE_MAX_JUMBO_FRAME_SIZE 0x2600 /* Maximum
> Jumbo
> >> frame size. */
> >>
> >> diff --git a/drivers/net/ixgbe/ixgbe_rxtx.c
> >> b/drivers/net/ixgbe/ixgbe_rxtx.c index 9a79d18..0ef7fdf 100644
> >> --- a/drivers/net/ixgbe/ixgbe_rxtx.c
> >> +++ b/drivers/net/ixgbe/ixgbe_rxtx.c
> >> @@ -4879,10 +4879,14 @@ ixgbe_dev_rx_init(struct rte_eth_dev *dev)
> >> hlreg0 &= ~IXGBE_HLREG0_JUMBOEN;
> >>
> >> /*
> >> - * If loopback mode is configured for 82599, set LPBK bit.
> >> + * If loopback mode is configured, set LPBK bit.
> >> */
> >> - if (hw->mac.type == ixgbe_mac_82599EB &&
> >> - dev->data->dev_conf.lpbk_mode ==
> IXGBE_LPBK_82599_TX_RX)
> >> + if ((hw->mac.type == ixgbe_mac_82599EB ||
> >> + hw->mac.type == ixgbe_mac_X540 ||
> >> + hw->mac.type == ixgbe_mac_X550 ||
> >> + hw->mac.type == ixgbe_mac_X550EM_x ||
> >> + hw->mac.type == ixgbe_mac_X550EM_a) &&
> >> + dev->data->dev_conf.lpbk_mode ==
> IXGBE_LPBK_TX_RX)
> >> hlreg0 |= IXGBE_HLREG0_LPBK;
> >> else
> >> hlreg0 &= ~IXGBE_HLREG0_LPBK;
> >> @@ -5088,6 +5092,29 @@ ixgbe_setup_loopback_link_82599(struct
> >> ixgbe_hw
> >> *hw)
> >> msec_delay(50);
> >> }
> >>
> >> +/*
> >> + * Set up link loopback for X540 / X550 mode Tx->Rx.
> >> + */
> >> +static inline void __attribute__((cold))
> >> +ixgbe_setup_loopback_link_x540_x550(struct ixgbe_hw *hw) {
> >> + uint32_t macc;
> >> + PMD_INIT_FUNC_TRACE();
> >> +
> >> + /* datasheet 15.2.1: MACC.FLU = 1 (force link up) */
> >> + macc = IXGBE_READ_REG(hw, IXGBE_MACC);
> >> + macc |= IXGBE_MACC_FLU;
> >> + IXGBE_WRITE_REG(hw, IXGBE_MACC, macc);
> >> +
> >> + /* Restart link */
> >> + IXGBE_WRITE_REG(hw,
> >> + IXGBE_AUTOC,
> >> + IXGBE_AUTOC_LMS_10G_LINK_NO_AN |
> IXGBE_AUTOC_FLU);
> >> +
> >> + hw->mac.ops.release_swfw_sync(hw, IXGBE_GSSR_MAC_CSR_SM);
> >> + msec_delay(50);
> >> +}
> >> +
> >>
> >> /*
> >> * Start Transmit and Receive Units.
> >> @@ -5148,10 +5175,16 @@ ixgbe_dev_rxtx_start(struct rte_eth_dev
> *dev)
> >> rxctrl |= IXGBE_RXCTRL_RXEN;
> >> hw->mac.ops.enable_rx_dma(hw, rxctrl);
> >>
> >> - /* If loopback mode is enabled for 82599, set up the link accordingly
> */
> >> - if (hw->mac.type == ixgbe_mac_82599EB &&
> >> - dev->data->dev_conf.lpbk_mode ==
> IXGBE_LPBK_82599_TX_RX)
> >> - ixgbe_setup_loopback_link_82599(hw);
> >> + /* If loopback mode is enabled, set up the link accordingly */
> >> + if (dev->data->dev_conf.lpbk_mode == IXGBE_LPBK_TX_RX) {
> >> + if (hw->mac.type == ixgbe_mac_82599EB)
> >> + ixgbe_setup_loopback_link_82599(hw);
> >> + else if (hw->mac.type == ixgbe_mac_X540 ||
> >> + hw->mac.type == ixgbe_mac_X550 ||
> >> + hw->mac.type == ixgbe_mac_X550EM_x ||
> >> + hw->mac.type == ixgbe_mac_X550EM_a)
> >> + ixgbe_setup_loopback_link_x540_x550(hw);
> >> + }
> >>
> >> #ifdef RTE_LIBRTE_SECURITY
> >> if ((dev->data->dev_conf.rxmode.offloads &
> >> --
> >> 2.10.2
> >
