If disable LSC when launching testpmd with X722, shown
link speed is 20G but not 10G. It's caused by wrongly
parsed link speed.
Correct it according to X722 datasheet.
Fixes: eef2daf2e199 ("net/i40e: fix link update no wait")
Cc: [email protected]
Signed-off-by: Beilei Xing <[email protected]>
---
drivers/net/i40e/i40e_ethdev.c | 45 +++++++++++++++++++++++++-----------------
1 file changed, 27 insertions(+), 18 deletions(-)
diff --git a/drivers/net/i40e/i40e_ethdev.c b/drivers/net/i40e/i40e_ethdev.c
index f6fc005..38d926b 100644
--- a/drivers/net/i40e/i40e_ethdev.c
+++ b/drivers/net/i40e/i40e_ethdev.c
@@ -2670,11 +2670,11 @@ update_link_reg(struct i40e_hw *hw, struct rte_eth_link
*link)
#define I40E_PRTMAC_MACC 0x001E24E0
#define I40E_REG_MACC_25GB 0x00020000
#define I40E_REG_SPEED_MASK 0x38000000
-#define I40E_REG_SPEED_100MB 0x00000000
-#define I40E_REG_SPEED_1GB 0x08000000
-#define I40E_REG_SPEED_10GB 0x10000000
-#define I40E_REG_SPEED_20GB 0x20000000
-#define I40E_REG_SPEED_25_40GB 0x18000000
+#define I40E_REG_SPEED_0 0x00000000
+#define I40E_REG_SPEED_1 0x08000000
+#define I40E_REG_SPEED_2 0x10000000
+#define I40E_REG_SPEED_3 0x18000000
+#define I40E_REG_SPEED_4 0x20000000
uint32_t link_speed;
uint32_t reg_val;
@@ -2688,26 +2688,35 @@ update_link_reg(struct i40e_hw *hw, struct rte_eth_link
*link)
/* Parse the link status */
switch (link_speed) {
- case I40E_REG_SPEED_100MB:
+ case I40E_REG_SPEED_0:
link->link_speed = ETH_SPEED_NUM_100M;
break;
- case I40E_REG_SPEED_1GB:
+ case I40E_REG_SPEED_1:
link->link_speed = ETH_SPEED_NUM_1G;
break;
- case I40E_REG_SPEED_10GB:
- link->link_speed = ETH_SPEED_NUM_10G;
- break;
- case I40E_REG_SPEED_20GB:
- link->link_speed = ETH_SPEED_NUM_20G;
+ case I40E_REG_SPEED_2:
+ if (hw->mac.type == I40E_MAC_X722)
+ link->link_speed = ETH_SPEED_NUM_2_5G;
+ else
+ link->link_speed = ETH_SPEED_NUM_10G;
break;
- case I40E_REG_SPEED_25_40GB:
- reg_val = I40E_READ_REG(hw, I40E_PRTMAC_MACC);
+ case I40E_REG_SPEED_3:
+ if (hw->mac.type == I40E_MAC_X722) {
+ link->link_speed = ETH_SPEED_NUM_5G;
+ } else {
+ reg_val = I40E_READ_REG(hw, I40E_PRTMAC_MACC);
- if (reg_val & I40E_REG_MACC_25GB)
- link->link_speed = ETH_SPEED_NUM_25G;
+ if (reg_val & I40E_REG_MACC_25GB)
+ link->link_speed = ETH_SPEED_NUM_25G;
+ else
+ link->link_speed = ETH_SPEED_NUM_40G;
+ }
+ break;
+ case I40E_REG_SPEED_4:
+ if (hw->mac.type == I40E_MAC_X722)
+ link->link_speed = ETH_SPEED_NUM_10G;
else
- link->link_speed = ETH_SPEED_NUM_40G;
-
+ link->link_speed = ETH_SPEED_NUM_20G;
break;
default:
PMD_DRV_LOG(ERR, "Unknown link speed info %u", link_speed);
--
2.5.5
