From: Stephen Hemminger <shemm...@brocade.com> All the debug chatter messages in the system log causes complaints from users. Change the INFO messages to DEBUG for normal startup kind of stuff.
Signed-off-by: Stephen Hemminger <stephen at networkplumber.org> --- drivers/net/ixgbe/ixgbe_ethdev.c | 14 +++++++------- drivers/net/ixgbe/ixgbe_rxtx.c | 22 +++++++++++----------- 2 files changed, 18 insertions(+), 18 deletions(-) diff --git a/drivers/net/ixgbe/ixgbe_ethdev.c b/drivers/net/ixgbe/ixgbe_ethdev.c index b7a60b1..0ff9583 100644 --- a/drivers/net/ixgbe/ixgbe_ethdev.c +++ b/drivers/net/ixgbe/ixgbe_ethdev.c @@ -576,7 +576,7 @@ ixgbe_dev_queue_stats_mapping_set(struct rte_eth_dev *eth_dev, (hw->mac.type != ixgbe_mac_X550EM_x)) return -ENOSYS; - PMD_INIT_LOG(INFO, "Setting port %d, %s queue_id %d to stat index %d", + PMD_INIT_LOG(DEBUG, "Setting port %d, %s queue_id %d to stat index %d", (int)(eth_dev->data->port_id), is_rx ? "RX" : "TX", queue_id, stat_idx); @@ -602,20 +602,20 @@ ixgbe_dev_queue_stats_mapping_set(struct rte_eth_dev *eth_dev, else stat_mappings->rqsmr[n] |= qsmr_mask; - PMD_INIT_LOG(INFO, "Set port %d, %s queue_id %d to stat index %d", + PMD_INIT_LOG(DEBUG, "Set port %d, %s queue_id %d to stat index %d", (int)(eth_dev->data->port_id), is_rx ? "RX" : "TX", queue_id, stat_idx); - PMD_INIT_LOG(INFO, "%s[%d] = 0x%08x", is_rx ? "RQSMR" : "TQSM", n, + PMD_INIT_LOG(DEBUG, "%s[%d] = 0x%08x", is_rx ? "RQSMR" : "TQSM", n, is_rx ? stat_mappings->rqsmr[n] : stat_mappings->tqsm[n]); /* Now write the mapping in the appropriate register */ if (is_rx) { - PMD_INIT_LOG(INFO, "Write 0x%x to RX IXGBE stat mapping reg:%d", + PMD_INIT_LOG(DEBUG, "Write 0x%x to RX IXGBE stat mapping reg:%d", stat_mappings->rqsmr[n], n); IXGBE_WRITE_REG(hw, IXGBE_RQSMR(n), stat_mappings->rqsmr[n]); } else { - PMD_INIT_LOG(INFO, "Write 0x%x to TX IXGBE stat mapping reg:%d", + PMD_INIT_LOG(DEBUG, "Write 0x%x to TX IXGBE stat mapping reg:%d", stat_mappings->tqsm[n], n); IXGBE_WRITE_REG(hw, IXGBE_TQSM(n), stat_mappings->tqsm[n]); } @@ -2297,7 +2297,7 @@ ixgbe_dev_interrupt_get_status(struct rte_eth_dev *dev) /* read-on-clear nic registers here */ eicr = IXGBE_READ_REG(hw, IXGBE_EICR); - PMD_DRV_LOG(INFO, "eicr %x", eicr); + PMD_DRV_LOG(DEBUG, "eicr %x", eicr); intr->flags = 0; if (eicr & IXGBE_EICR_LSC) { @@ -2338,7 +2338,7 @@ ixgbe_dev_link_status_print(struct rte_eth_dev *dev) PMD_INIT_LOG(INFO, " Port %d: Link Down", (int)(dev->data->port_id)); } - PMD_INIT_LOG(INFO, "PCI Address: %04d:%02d:%02d:%d", + PMD_INIT_LOG(DEBUG, "PCI Address: %04d:%02d:%02d:%d", dev->pci_dev->addr.domain, dev->pci_dev->addr.bus, dev->pci_dev->addr.devid, diff --git a/drivers/net/ixgbe/ixgbe_rxtx.c b/drivers/net/ixgbe/ixgbe_rxtx.c index b1db57f..ecd2184 100644 --- a/drivers/net/ixgbe/ixgbe_rxtx.c +++ b/drivers/net/ixgbe/ixgbe_rxtx.c @@ -1,4 +1,4 @@ -/*- + /*- * BSD LICENSE * * Copyright(c) 2010-2015 Intel Corporation. All rights reserved. @@ -1874,23 +1874,23 @@ ixgbe_set_tx_function(struct rte_eth_dev *dev, struct ixgbe_tx_queue *txq) /* Use a simple Tx queue (no offloads, no multi segs) if possible */ if (((txq->txq_flags & IXGBE_SIMPLE_FLAGS) == IXGBE_SIMPLE_FLAGS) && (txq->tx_rs_thresh >= RTE_PMD_IXGBE_TX_MAX_BURST)) { - PMD_INIT_LOG(INFO, "Using simple tx code path"); + PMD_INIT_LOG(DEBUG, "Using simple tx code path"); #ifdef RTE_IXGBE_INC_VECTOR if (txq->tx_rs_thresh <= RTE_IXGBE_TX_MAX_FREE_BUF_SZ && (rte_eal_process_type() != RTE_PROC_PRIMARY || ixgbe_txq_vec_setup(txq) == 0)) { - PMD_INIT_LOG(INFO, "Vector tx enabled."); + PMD_INIT_LOG(DEBUG, "Vector tx enabled."); dev->tx_pkt_burst = ixgbe_xmit_pkts_vec; } else #endif dev->tx_pkt_burst = ixgbe_xmit_pkts_simple; } else { - PMD_INIT_LOG(INFO, "Using full-featured tx code path"); - PMD_INIT_LOG(INFO, + PMD_INIT_LOG(DEBUG, "Using full-featured tx code path"); + PMD_INIT_LOG(DEBUG, " - txq_flags = %lx " "[IXGBE_SIMPLE_FLAGS=%lx]", (unsigned long)txq->txq_flags, (unsigned long)IXGBE_SIMPLE_FLAGS); - PMD_INIT_LOG(INFO, + PMD_INIT_LOG(DEBUG, " - tx_rs_thresh = %lu " "[RTE_PMD_IXGBE_TX_MAX_BURST=%lu]", (unsigned long)txq->tx_rs_thresh, (unsigned long)RTE_PMD_IXGBE_TX_MAX_BURST); @@ -3766,11 +3766,11 @@ ixgbe_set_rx_function(struct rte_eth_dev *dev) */ if (dev->data->lro) { if (adapter->rx_bulk_alloc_allowed) { - PMD_INIT_LOG(INFO, "LRO is requested. Using a bulk " + PMD_INIT_LOG(DEBUG, "LRO is requested. Using a bulk " "allocation version"); dev->rx_pkt_burst = ixgbe_recv_pkts_lro_bulk_alloc; } else { - PMD_INIT_LOG(INFO, "LRO is requested. Using a single " + PMD_INIT_LOG(DEBUG, "LRO is requested. Using a single " "allocation version"); dev->rx_pkt_burst = ixgbe_recv_pkts_lro_single_alloc; } @@ -3786,7 +3786,7 @@ ixgbe_set_rx_function(struct rte_eth_dev *dev) dev->rx_pkt_burst = ixgbe_recv_scattered_pkts_vec; } else if (adapter->rx_bulk_alloc_allowed) { - PMD_INIT_LOG(INFO, "Using a Scattered with bulk " + PMD_INIT_LOG(DEBUG, "Using a Scattered with bulk " "allocation callback (port=%d).", dev->data->port_id); dev->rx_pkt_burst = ixgbe_recv_pkts_lro_bulk_alloc; @@ -3808,7 +3808,7 @@ ixgbe_set_rx_function(struct rte_eth_dev *dev) * - Single buffer allocation (the simplest one) */ } else if (adapter->rx_vec_allowed) { - PMD_INIT_LOG(INFO, "Vector rx enabled, please make sure RX " + PMD_INIT_LOG(DEBUG, "Vector rx enabled, please make sure RX " "burst size no less than 32."); dev->rx_pkt_burst = ixgbe_recv_pkts_vec; @@ -3966,7 +3966,7 @@ ixgbe_set_rsc(struct rte_eth_dev *dev) dev->data->lro = 1; - PMD_INIT_LOG(INFO, "enabling LRO mode"); + PMD_INIT_LOG(DEBUG, "enabling LRO mode"); return 0; } -- 2.1.4