One ought to reuse existing header structs in flow items.
This particular item contains non-header fields, so it's
important to keep the header fields in a separate struct.
Signed-off-by: Ivan Malov <ivan.ma...@oktetlabs.ru>
Reviewed-by: Andrew Rybchenko <andrew.rybche...@oktetlabs.ru>
Reviewed-by: Andy Moreton <amore...@xilinx.com>
---
lib/librte_ethdev/rte_flow.h | 44 ++++++++++++++++++++++--------------
1 file changed, 27 insertions(+), 17 deletions(-)
diff --git a/lib/librte_ethdev/rte_flow.h b/lib/librte_ethdev/rte_flow.h
index 669e677e9..96fd93ee1 100644
--- a/lib/librte_ethdev/rte_flow.h
+++ b/lib/librte_ethdev/rte_flow.h
@@ -728,22 +728,32 @@ static const struct rte_flow_item_raw
rte_flow_item_raw_mask = {
*
* Matches an Ethernet header.
*
- * The @p type field either stands for "EtherType" or "TPID" when followed
- * by so-called layer 2.5 pattern items such as RTE_FLOW_ITEM_TYPE_VLAN. In
- * the latter case, @p type refers to that of the outer header, with the
- * inner EtherType/TPID provided by the subsequent pattern item. This is the
- * same order as on the wire.
- * If the @p type field contains a TPID value, then only tagged packets with
the
- * specified TPID will match the pattern.
- * The field @p has_vlan can be used to match any type of tagged packets,
- * instead of using the @p type field.
- * If the @p type and @p has_vlan fields are not specified, then both tagged
- * and untagged packets will match the pattern.
+ * Inside @p hdr field, the sub-field @p ether_type stands either for EtherType
+ * or TPID, depending on whether the item is followed by a VLAN item or not. If
+ * two VLAN items follow, the sub-field refers to the outer one, which, in
turn,
+ * contains the inner TPID in the similar header field. The innermost VLAN item
+ * contains a layer-3 EtherType. All of that follows the order seen on the
wire.
+ *
+ * If the field in question contains a TPID value, only tagged packets with the
+ * specified TPID will match the pattern. Alternatively, it's possible to match
+ * any type of tagged packets by means of the field @p has_vlan rather than use
+ * the EtherType/TPID field. Also, it's possible to leave the two fields
unused.
+ * If this is the case, both tagged and untagged packets will match the
pattern.
*/
+RTE_STD_C11
struct rte_flow_item_eth {
- struct rte_ether_addr dst; /**< Destination MAC. */
- struct rte_ether_addr src; /**< Source MAC. */
- rte_be16_t type; /**< EtherType or TPID. */
+ union {
+ struct {
+ /*
+ * These fields are retained for compatibility.
+ * Please switch to the new header field below.
+ */
+ struct rte_ether_addr dst; /**< Destination MAC. */
+ struct rte_ether_addr src; /**< Source MAC. */
+ rte_be16_t type; /**< EtherType or TPID. */
+ };
+ struct rte_ether_hdr hdr;
+ };
uint32_t has_vlan:1; /**< Packet header contains at least one VLAN. */
uint32_t reserved:31; /**< Reserved, must be zero. */
};
@@ -751,9 +761,9 @@ struct rte_flow_item_eth {
/** Default mask for RTE_FLOW_ITEM_TYPE_ETH. */
#ifndef __cplusplus
static const struct rte_flow_item_eth rte_flow_item_eth_mask = {
- .dst.addr_bytes = "\xff\xff\xff\xff\xff\xff",
- .src.addr_bytes = "\xff\xff\xff\xff\xff\xff",
- .type = RTE_BE16(0x0000),
+ .hdr.d_addr.addr_bytes = "\xff\xff\xff\xff\xff\xff",
+ .hdr.s_addr.addr_bytes = "\xff\xff\xff\xff\xff\xff",
+ .hdr.ether_type = RTE_BE16(0x0000),
};
#endif
--
2.20.1
