> -----Original Message-----
> From: Ferruh Yigit <[email protected]>
> Sent: Thursday, October 20, 2022 22:45
> To: Guo, Junfeng <[email protected]>; Zhang, Qi Z
> <[email protected]>; Wu, Jingjing <[email protected]>; Xing,
> Beilei <[email protected]>
> Cc: [email protected]; Li, Xiaoyun <[email protected]>;
> [email protected]; Richardson, Bruce
> <[email protected]>; [email protected];
> [email protected]; Xia, Chenbo <[email protected]>;
> Zhang, Helin <[email protected]>
> Subject: Re: [PATCH v6 5/8] net/gve: add support for MTU setting
>
> On 10/20/2022 11:36 AM, Junfeng Guo wrote:
>
> >
> > Support dev_ops mtu_set.
> >
> > Signed-off-by: Xiaoyun Li <[email protected]>
> > Signed-off-by: Junfeng Guo <[email protected]>
> > ---
> > doc/guides/nics/features/gve.ini | 1 +
> > drivers/net/gve/gve_ethdev.c | 27 +++++++++++++++++++++++++++
> > 2 files changed, 28 insertions(+)
> >
> > diff --git a/doc/guides/nics/features/gve.ini
> b/doc/guides/nics/features/gve.ini
> > index ae466ad677..d1703d8dab 100644
> > --- a/doc/guides/nics/features/gve.ini
> > +++ b/doc/guides/nics/features/gve.ini
> > @@ -5,6 +5,7 @@
> > ;
> > [Features]
> > Link status = Y
> > +MTU update = Y
> > Linux = Y
> > x86-32 = Y
> > x86-64 = Y
> > diff --git a/drivers/net/gve/gve_ethdev.c
> b/drivers/net/gve/gve_ethdev.c
> > index ca4a467140..1968f38eb6 100644
> > --- a/drivers/net/gve/gve_ethdev.c
> > +++ b/drivers/net/gve/gve_ethdev.c
> > @@ -94,12 +94,39 @@ gve_dev_close(struct rte_eth_dev *dev)
> > return err;
> > }
> >
> > +static int
> > +gve_dev_mtu_set(struct rte_eth_dev *dev, uint16_t mtu)
> > +{
> > + struct gve_priv *priv = dev->data->dev_private;
> > + int err;
> > +
> > + if (mtu < RTE_ETHER_MIN_MTU || mtu > priv->max_mtu) {
> > + PMD_DRV_LOG(ERR, "MIN MTU is %u MAX MTU is %u",
> RTE_ETHER_MIN_MTU, priv->max_mtu);
>
> Although this is within new 100 column limit, it is easy to break it
> without sacrificing the readability, can you break it as something like:
>
> PMD_DRV_LOG(ERR, "MIN MTU is %u MAX MTU is %u",
> RTE_ETHER_MIN_MTU, priv->max_mtu);
Sure, will improve this. Thanks!
>
> > + return -EINVAL;
> > + }
> > +
> > + /* mtu setting is forbidden if port is start */
> > + if (dev->data->dev_started) {
> > + PMD_DRV_LOG(ERR, "Port must be stopped before
> configuration");
> > + return -EBUSY;
> > + }
> > +
> > + err = gve_adminq_set_mtu(priv, mtu);
> > + if (err) {
> > + PMD_DRV_LOG(ERR, "Failed to set mtu as %u err = %d", mtu,
> err);
> > + return err;
> > + }
> > +
> > + return 0;
> > +}
>
>
> configure() (gve_dev_configure()) also get 'mtu' as user config
> ('eth_conf->rxmode.mtu') which is ignored right now,
>
> since there is 'gve_adminq_set_mtu()' command already what do you
> think
> to use it within 'gve_dev_configure()'?
Do you mean to set the mtu with the user config value like:
'gve_dev_mtu_set(dev, dev->data->dev_conf.rxmode.mtu)'
within 'gve_dev_configure()'?
The ' dev->data->dev_conf.rxmode.mtu' I get at dev configure stage
is also 1500, which is lager than priv->max_mtu (1460). And this may
still cause the testpmd launch failed...
So I'll keep this part unchanged and do more investigations to figure
out the mtu issues we met. Thanks!
>
> > +
> > static const struct eth_dev_ops gve_eth_dev_ops = {
> > .dev_configure = gve_dev_configure,
> > .dev_start = gve_dev_start,
> > .dev_stop = gve_dev_stop,
> > .dev_close = gve_dev_close,
> > .link_update = gve_link_update,
> > + .mtu_set = gve_dev_mtu_set,
> > };
> >
> > static void
> > --
> > 2.34.1
> >
