From: Maciej Czekaj <maciej.cze...@caviumnetworks.com> "flowgen" forwarding mode has fixed packet size (300). Let it re-use --txpkts option for specifying generated packet size.
Signed-off-by: Maciej Czekaj <maciej.czekaj at caviumnetworks.com> --- app/test-pmd/config.c | 2 +- app/test-pmd/flowgen.c | 3 +-- app/test-pmd/parameters.c | 3 ++- doc/guides/testpmd_app_ug/run_app.rst | 3 ++- doc/guides/testpmd_app_ug/testpmd_funcs.rst | 2 +- 5 files changed, 7 insertions(+), 6 deletions(-) diff --git a/app/test-pmd/config.c b/app/test-pmd/config.c index bfcbff9..db682bd 100644 --- a/app/test-pmd/config.c +++ b/app/test-pmd/config.c @@ -954,7 +954,7 @@ rxtx_config_display(void) rx_mode.hw_strip_crc ? "enabled" : "disabled", nb_pkt_per_burst); - if (cur_fwd_eng == &tx_only_engine) + if (cur_fwd_eng == &tx_only_engine || cur_fwd_eng == &flow_gen_engine) printf(" packet len=%u - nb packet segments=%d\n", (unsigned)tx_pkt_length, (int) tx_pkt_nb_segs); diff --git a/app/test-pmd/flowgen.c b/app/test-pmd/flowgen.c index a6abe91..e6b1ea2 100644 --- a/app/test-pmd/flowgen.c +++ b/app/test-pmd/flowgen.c @@ -74,7 +74,6 @@ /* hardcoded configuration (for now) */ static unsigned cfg_n_flows = 1024; -static unsigned cfg_pkt_size = 300; static uint32_t cfg_ip_src = IPv4(10, 254, 0, 0); static uint32_t cfg_ip_dst = IPv4(10, 253, 0, 0); static uint16_t cfg_udp_src = 1000; @@ -118,7 +117,7 @@ ip_sum(const unaligned_uint16_t *hdr, int hdr_len) static void pkt_burst_flow_gen(struct fwd_stream *fs) { - unsigned pkt_size = cfg_pkt_size - 4; /* Adjust FCS */ + unsigned pkt_size = tx_pkt_length - 4; /* Adjust FCS */ struct rte_mbuf *pkts_burst[MAX_PKT_BURST]; struct rte_mempool *mbp; struct rte_mbuf *pkt; diff --git a/app/test-pmd/parameters.c b/app/test-pmd/parameters.c index 8792c2c..c498b4b 100644 --- a/app/test-pmd/parameters.c +++ b/app/test-pmd/parameters.c @@ -191,7 +191,8 @@ usage(char* progname) "(0 <= mapping <= %d).\n", RTE_ETHDEV_QUEUE_STAT_CNTRS - 1); printf(" --no-flush-rx: Don't flush RX streams before forwarding." " Used mainly with PCAP drivers.\n"); - printf(" --txpkts=X[,Y]*: set TX segment sizes.\n"); + printf(" --txpkts=X[,Y]*: set TX segment sizes" + " or total packet length.\n"); printf(" --disable-link-check: disable check on link status when " "starting/stopping ports.\n"); } diff --git a/doc/guides/testpmd_app_ug/run_app.rst b/doc/guides/testpmd_app_ug/run_app.rst index 7712bd2..34bf924 100644 --- a/doc/guides/testpmd_app_ug/run_app.rst +++ b/doc/guides/testpmd_app_ug/run_app.rst @@ -450,7 +450,8 @@ The commandline options are: * ``--txpkts=X[,Y]`` - Set TX segment sizes. + Set TX segment sizes or total packet length. Valid for ``tx-only`` + and ``flowgen`` forwarding modes. * ``--disable-link-check`` diff --git a/doc/guides/testpmd_app_ug/testpmd_funcs.rst b/doc/guides/testpmd_app_ug/testpmd_funcs.rst index f87e0c2..c1868e6 100644 --- a/doc/guides/testpmd_app_ug/testpmd_funcs.rst +++ b/doc/guides/testpmd_app_ug/testpmd_funcs.rst @@ -405,7 +405,7 @@ When retry is enabled, the transmit delay time and number of retries can also be set txpkts ~~~~~~~~~~ -Set the length of each segment of the TX-ONLY packets:: +Set the length of each segment of the TX-ONLY packets or length of packet for FLOWGEN mode:: testpmd> set txpkts (x[,y]*) -- 2.7.4