There is an alternate solution for 2.4.x that is simpler for me to offer. it could be argued that an abandoned project, deprecated in 2015, and entirely abandoned effective June 2021, is only supported with an explicit path to the pcre-config file, and that only pcre2-config would ever be searched for in future 2.4.x releases, whether we observe --with-pcre or establish a new --with-pcre2 config flag. It might not be a bad idea at this point, since there is no indication of a future httpd major or minor version bump, given the fierce resistance.
On Fri, Oct 21, 2022 at 5:18 PM William A Rowe Jr <wr...@rowe-clan.net> wrote: > > The error below is acknowledged, and I worked out how it escaped my radar > (when pcre2-config exists, the current logic tolerates a broken > --with-pcre=/path, > finds the system pcre2-config or pcre-config, and if another dependency picks > the same path, the "desired" pcre is used and httpd assumes it is the version > of the system located -config file.) > > I'd like to spend a moment setting fresh and realistic expectations of > the correct > behavior, and start by proposing to add a new --with-pcre2 to httpd 2.4.x. > These > two flags would interact as follows; > > --with-pcre2 (Default) --with-pcre (Default) > Search the system path for pcre2-config, then for legacy pcre-config scripts > > --with-pcre2 (Default) --without-pcre > Search the system path for ONLY pcre2-config script > > --without-pcre2 --with-pcre (Default) > Search the system path for ONLY legacy pcre-config script > > --without-pcre2 --without-pcre > Absolute failure to configure > > --with-pcre2 (Default) --with-pcre=/path > Search only /path-to-explicit-config, /path/bin/pcre2-config, > /path/pcre2-config, > /path/bin/pcre-config, and /path/pcre-config in that order. > Will not fall back from explicit path to system path. > > --with-pcre2=/path --without-pcre > *or* > --with-pcre2=/path --with-pcre (Default) > Search only /path-to-explicit-config, /path/bin/pcre2-config, and > /path/pcre2-config > Will not fall back from explicit path to system path. > > --without-pcre2 --with-pcre=/path > Search only /path-to-explicit-config, /path/bin/pcre-config, and > /path/pcre-config > (pre-2.4.53 behavior; however no longer falls back from explicit path > to system path.) > > --with-pcre2=/path --with-pcre=/path > Absolute failure to configure, can't have both. > > I need to determine if we can distinguish between default and explicit > specified --with toggles. If so, then we can handle... > > --with-pcre2 (Explicit) --with-pcre (Default) > Search the system path for ONLY pcre2-config scripts. > > --with-pcre2=/path --with-pcre (Explicit) > *or* > --with-pcre2 (Explicit) --with-pcre=/path > *or* > --with-pcre2 (Explicit) --with-pcre (Explicit) > Absolute failure to configure, can't have both. > > I'd propose if this is accepted after 2.4.next release feedback, that > all legacy pcre 8.x and early support is ripped out, and honor only the > --with-pcre2[=path] syntax and forcefully reject the --with-pcre option. > The suggestions above should provide a mostly painless transition > to move from 2.4.next to subsequent releases. > > Thoughts/comments/objections? > > Bill > > On Mon, Apr 25, 2022 at 5:59 AM Ruediger Pluem <rpl...@apache.org> wrote: > > > > See https://bz.apache.org/bugzilla/show_bug.cgi?id=66000 > > > > On 4/25/22 11:16 AM, Ganeshprasad MS wrote: > > > We have downloaded the Apache HTTPD source httpd-2.4.53.tar.gz > > > <https://dlcdn.apache.org/httpd/httpd-2.4.53.tar.gz> from Apache > > > software foundation and trying to compile/build the Apache binaries, but > > > we are facing the below error while configuring the > > > Apache HTTPD. > > > > Options: --prefix > > > /remote/users/gms/2.4.53/apache-pack/build/PKL-AWS-2.4.53.0/Release > > > --enable-proxy --enable-proxy-ajp > > > --enable-proxy-balancer --enable-proxy-http --enable-rewrite > > > --enable-info --enable-headers --enable-expires --enable-deflate > > > --enable-ssl > > > --with-ssl=/remote/users/gms/2.4.53/apache-pack/build/PKL-AWS-2.4.53.0/Release > > > --with-pcre=/remote/users/gms/2.4.53/apache-pack/build/pcre > > > --with-apr=/remote/users/gms/2.4.53/apache-pack/build/apr > > > --with-apr-util=/remote/users/gms/2.4.53/apache-pack/build/apr-util > > > --with-crypto > > > > checking for -pcre2-config... no > > > checking for -pcre-config... no > > > checking for pcre2-config... no > > > checking for pcre-config... pcre-config > > > configure: error: Did not find working script at pcre-config
