Adding missing defconfig From: Thomas Axelsson <thomas.axels...@actia.se> Sent: den 20 februari 2020 12:24 To: dev@nuttx.apache.org Subject: IMXRT 1060 USB Device (copy of LPC43/LPC31 driver) - Set-up buffer problems
Hi, I'm trying to get the IMXRT1060-EVK working as a USB device using the USB OTG1 peripheral. By comparing reference manuals, I've figured that the USB peripheral seems to be identical to the one found in NXP LPC43xx (and LPC31xx). As such, I've copied lpc43_usb0dev.c, replaced all the registers with the IMX RT registers and tweaked the initialization. I have made some ugly copies (throwing in the PLL init in the driver) that will need to be cleaned up, once the driver is working. Also, it is currently full of small hacks, trying to get it to work. I have included the almost unmodified, copied LPC43 driver, in the patch as well, for comparison. The driver is almost working, but I've stumbled on a problem with reading the Set-up buffer in the EP0 Queue Head (g_qh[0].setup) (struct that resides in RAM). What I've found is that 1. The host sends Get Descriptor and the device responds correctly. (Green line in USB trace image) 2. The host sends Set Address (not visible in Linux usbmon trace!) but the device reads the old Get Descriptor packet from g_qh[0].setup and responds as if Get Descriptor was sent. (Blue line and following red text in USB trace image) When playing around with the code I have sometimes found .setup to be all zeroes, when the host does Get Descriptor, Reset, <something>. Meaning that the zeroes written by imxrt_usbreset() has not been overwritten by the USB controller. I have also at one time managed to read .setup repeatedly, after the ENDPTSETUPSTAT has been set, until the value changed and gotten the Set Address. However, I'm having a hard time to reproduce it. So it seems that the data in g_qh[0].setup is only filled correctly for the first setup package and not updated again, or sometimes updated with a large delay. I have tried sprinkling some volatile, in case the imxrt_readsetup() code would skip the memory access, without success. Any ideas on what might be going wrong or where to dig? I have included the current state of the driver (imxrt_usbdev.c) and a patch+defconfig if someone wants to play on an IMXRT EVK. The patch was generated against NuttX master branch. Here is a snippet from the console output on the device, showing how the device reacts to Get Descriptor followed by Set Address. Please note that ENTRY and EP0SETUP is doubly traced since I've duplicated the trace lines in the code. Interrupt decode 8: IMXRT_TRACEINTID_EP0SETUP 0001 Interrupt decode 8: IMXRT_TRACEINTID_EP0SETUP 0001 Interrupt decode 18: IMXRT_TRACEINTID_GETSETDESC 0000 Interrupt decode 5: IMXRT_TRACEINTID_DISPATCH 0000 ... Interrupt entry 1: ENTRY 0000 Interrupt entry 1: ENTRY 0081 Interrupt decode 8: IMXRT_TRACEINTID_EP0SETUP 0001 Interrupt decode 8: IMXRT_TRACEINTID_EP0SETUP 0001 Interrupt decode 18: IMXRT_TRACEINTID_GETSETDESC 0000 <<--- This should have been SETADDRESS! Interrupt decode 5: IMXRT_TRACEINTID_DISPATCH 0000 Testing the patch: git checkout 90839b41f92aa01f1b0b24d18ee62e6efa4077d5 # or current master apply the patch tools/configure.sh imxrt1060-evk:nsh cp downloads/defconfig defconfig make olddefconfig make Flash board Connect USBOTG1 (connector J9) to host. Press <enter> in nsh to see the usbtrace (I did not manage to use the USB Monitor with NSH). (I've found that I have to toggle the boot config to 0000 on SW7 and reset, to be able to flash with J-Link after starting this NuttX config. It does not happen in my dev code, so I'm ignoring that issue.) Thomas Axelsson SW Developer ACTIA Nordic AB (part of ACTIA Group) Mail: thomas.axels...@actia.se<mailto:thomas.axels...@actia.se> Web: www.actia.se<http://www.actia.se/> [cid:image001.png@01D5E7E9.029B3520]
