Hi Ricardo, I don't know if this is major problem but when i run #iwconifg msh0 it shows that the msh0 mode=repeater I am running firmware version 3107. if i try to iwconfig msh0 ap any or any other iwconfig command on msh0 it does not work. My eth0 is on ad-hoc mode. I tried unplugging the antenna and replugging it but when i do service network restart it never comes up.
Is that the right mode for eth0 and msh0. Is there a way to manually change the mode on msh0?? However, i can ping the internet through the antenna. Should i be able to do that on a repeater mode? P.S: I did manage to find the iwpriv msh0 fwt_list on the xo's and the laptop. best, Sulochan. On Wed, Feb 20, 2008 at 7:42 PM, Ricardo Carrano <[EMAIL PROTECTED]> wrote: > Hi Sulochan! > > Assuming it is your XO2 fwt_list, it should be populated with paths to > XO1 (via XO1) and XS (via XO1 or XS, depending whether the XS is in reach). > The way it is (empty) this means your XO has no path for any other XO. It > is lonely and sad ;-) > But, please keep in mind that these entries expiry (I don't recall how > long does it take - but it's not long), so you should check them during the > test. Is that the case? > > On Feb 20, 2008 9:20 AM, sulochan acharya <[EMAIL PROTECTED]> wrote: > > > Hi Ricardo, > > I have iwpriv showing > > NULL on all the fwt_list . > > What should it be set to? > > > > best, > > Sulochan. > > > > > > > > On Feb 19, 2008 5:41 PM, Ricardo Carrano <[EMAIL PROTECTED]> > > wrote: > > > > > Sulochan, > > > > > > You should check your forwarding (layer two) table with : iwpriv msh0 > > > fwt_list <index> (<index> is 0,1,2,...) > > > > > > Look for an entry that forwards the frames destined to the anycast mac > > > address of the server (c0:27:c0:27:c0:00) via the mac address of the first > > > XO. > > > > > > Traceroute/path will show you layer three (IP) routes. > > > > > > Regards, > > > Ricardo Carrano > > > > > > 2008/2/19 sulochan acharya <[EMAIL PROTECTED]>: > > > > > > > Folks, > > > > I can not hop from xo to xo to xs. > > > > Here is what I did: > > > > > > > > One XO closer to the server with active antenna.....and i can ping > > > > the server from this laptop. > > > > > > > > Another XO closer to the first laptop ( i can chat with this XO) but > > > > further away from the server. > > > > > > > > Now technically i should be able to ping the server through the > > > > first laptop, but I cant :( > > > > > > > > Is there some additional things i need to (like adding packages) go > > > > through to get this to work? > > > > > > > > Or is it just out of range? If so how it is different from one > > > > laptop talking to another laptop? > > > > > > > > Is there a way i can check that the packet is being relayed (other > > > > than doing trace rout ) ? > > > > > > > > Also, can i for test purposes change the mesh DHCP to give out ipv4 > > > > and not ipv6? Would this make > > > > some other features not work? > > > > > > > > best, > > > > -Sulochan > > > > > > > > _______________________________________________ > > > > Devel mailing list > > > > Devel@lists.laptop.org > > > > http://lists.laptop.org/listinfo/devel > > > > > > > > > > > > > >
_______________________________________________ Devel mailing list Devel@lists.laptop.org http://lists.laptop.org/listinfo/devel